Table of Contents
Related Manuals for SOYO SY-5EH5/5EHM V1.2 Super 7
Summary of Contents for SOYO SY-5EH5/5EHM V1.2 Super 7
-
Page 1: Technical Reference
SY-5EH5/5EHM V1.2 Super 7™ Motherboard ************************************************ ® Pentium Class CPU supported ETEQ82C663 PCI/AGP Motherboard AT Form Factor ************************************************ User's Guide & Technical Reference... - Page 2 2000. The “SY-5EHM/5EH5: system is eligible to carry the NSTL :Year 2000 Certification” seal. The Year 2000 certification test has been done under the following system configuration: Company Name : SOYO COMPUTER INC. System Model Name : SY-5EHM/5EH5 Hardware Revision...
-
Page 3: Declaration Of Conformity
Monitor: SONY/AK8GDM17SE2T Printer: HP/DS17XU2225 Modem: ACEEX/IF AXDM1414 Keyboard: SILITED/GYUM99SK This declaration is given for the manufacturer SOYO COMPUTER INC. No.21, Wu-Kung 5 Rd., Hsing Chuang City, Taipei Hsien, Taiwan, R.O.C. The test was carried out by SPORTON INTERNATIONAL INC. 6F, No. 106, Hsin Tai Wu Rd., Sec. 1, His Chih,... -
Page 4: About This Guide
It is the policy of Soyo Computer Inc. to respect the valid patent rights of third parties and not to infringe upon or assist others to infringe upon such rights. -
Page 5: Table Of Contents
Table of Contents SY-5EHM/5EH5 V1.2 Table of Contents SY-5EHM/5EH5 V1.2 MOTHERBOARD LAYOUT....... 1 CHAPTER 1 INTRODUCTION............2 KEY FEATURES ............2 HANDLING THE MOTHERBOARD ....... 5 ELECTROSTATIC DISCHARGE PRECAUTIONS..5 CHAPTER 2 HARDWARE SETUP ............ 6 PREPARATIONS ............6 UNPACKING THE MOTHERBOARD ......7 INSTALLATION GUIDE..........8 CHAPTER 3 BIOS SETUP UTILITY .......... -
Page 6: Sy-5Ehm/5Eh5 V1.2 Motherboard Layout
Motherboard Features SY-5EHM/5EH5 V1.2 SY-5EHM/5EH5 V1.2 Motherboard Layout PS/2 Mouse Connector Connector Flash BIOS AT Power Lithium PRT 1 COM 2 Battery FDC37C669Q ATX Power USB1 JP44 COM 1 AGP Slot PCI Slot #3 PCI Slot #2 PCI Slot #1 IDE 1 IDE 2 ISA Slot #3 ETEQ... -
Page 7: Chapter 1 Introduction
Introduction SY-5EHM/5EH5 V1.2 Chapter 1 INTRODUCTION The SY-5EHM/5EH5 V1.2 AGP/PCI Motherboard is a high- performance AT form-factor system board. SY-5EHM/5EH5 V1.2 uses the ETEQ82C663 AGP/PCI Chipset technology and supports ® Pentium class processors. This Motherboard is fully compatible with industry standards and adds many technical enhancements. 1-1 KEY FEATURES Ø... -
Page 8: Memory Configuration
Introduction SY-5EHM/5EH5 V1.2 2 x 168-pin DIMM banks support 8/16/32/64/128/256 MB unbuffered DIMM modules Ø Support 2 strips of 72-pin FPM/EDO SIMM 2 x 72-pin SIMM banks support 8/16/32/64 MB SIMM modules Ø Memory configuration: System memory: 8MB to 640MB with EDO/SDRAM SY-5EHM/5EH5 V1.2 PLATFORM FEATURES Board Size 4-layer PCB, 22x23cm(8.7”x9.1”), AT Form Factor... - Page 9 Introduction SY-5EHM/5EH5 V1.2 5-pin Serial Infrared Device Connector Keylock 5-pin KeyLock Connector Reset 2-pin Reset Switch Connector Speaker 4-pin PC Speaker Connector TB_LED 2-pin Turbo LED Connector HDD_LED 2-pin IDE Device LED Connector PWRBT ATX Power On/Off Switch 2-pin Connector Single or Dual voltage selection Jumper CMOS Clear Jumper CPU bus clock frequency Jumper...
-
Page 10: Handling The Motherboard
Introduction SY-5EHM/5EH5 V1.2 1-2 HANDLING THE MOTHERBOARD To avoid damage to your Motherboard, follow these simple rules while unpacking: Ø Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. Ø Remove the Motherboard from its anti-static packaging. Hold the Motherboard by the edges and avoid touching its components. -
Page 11: Chapter 2 Hardware Setup
Hardware Setup SY-5EHM/5EH5 V1.2 Chapter 2 HARDWARE SETUP Congratulations on your purchase of SY-5EHM/5EH5 V1.2 Super 7 Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti-static packaging until you have made the following preparations. -
Page 12: Unpacking The Motherboard
Hardware Setup SY-5EHM/5EH5 V1.2 2-2 Unpacking the Motherboard When unpacking the Motherboard, check for the following items: Ø The SY-5EHM/5EH5 V1.2 ETEQ82C663 PCI/AGP Motherboard Ø The Quick Start Guide * Ø The Installation CD-ROM * Ø The CPU Retention Set Ø... -
Page 13: Installation Guide
Hardware Setup SY-5EHM/5EH5 V1.2 2-3 Installation Guide We will now begin the installation of the Motherboard. Please follow the step-by-step procedure designed to lead you to a complete and correct installation. Step 1. CPU Installation ® Follow these instructions to install your Pentium class processor correctly. - Page 14 Hardware Setup SY-5EHM/5EH5 V1.2 Follow these steps to install the CPU in the Socket 7: Lift the socket handle up to a vertical position. Align the blunt edge of the CPU with the matching pin-hole distinctive edge on the socket. Seat the processor in the socket completely and without forcing.
- Page 15 Hardware Setup SY-5EHM/5EH5 V1.2 Step 3. CPU Voltage Setting (SW2,JP1) Single or Dual Voltage Selection CPU Voltage Please verify the correct voltage with your dealer before installation. Use the following tables to set SW2 to the proper "Voltage Value", according to the specifications marked on your CPU: This Motherboard comes with pre-configured setting of CPU voltage.
- Page 16 Hardware Setup SY-5EHM/5EH5 V1.2 markets. Therefore, always make sure you know the type of the CPU you are installing and adjust the settings on SW2 accordingly. This motherboard supports CPU core voltages from 2.0 to 3.5V in 0.1V increments. Use the following tables to set the CPU voltage jumpers SW2 to match the voltage value of your CPU: CPU Core Voltage Setting: SW2 Voltage Value...
- Page 17 Hardware Setup SY-5EHM/5EH5 V1.2 Voltage Settings for Various Processors Processor Voltage Value: SW2 Voltage Setting Single Voltage Intel P54C - P100 :3.3V Intel P54C - P133 :3.3V Single Voltage Intel P54C - P166 :3.5V Intel P54C - P200 :3.5V Dual Voltage Intel P55C - P166 :2.8V Intel P55C - P200...
- Page 18 Hardware Setup SY-5EHM/5EH5 V1.2 Voltage Settings for Various Processors (continued) Processor Voltage Value: SW2 Voltage Setting AMD K6-2 450 AMD K6-2 475 Dual Voltage AMD K6-2 500 :2.4V AMD K6-III 400 :3.3V AMD K6-III 450 The AMD K6-2 and K6-III come in several versions with different voltages.
- Page 19 Hardware Setup SY-5EHM/5EH5 V1.2 Step 4. CPU Frequency Setting (SW1) 1 2 3 4 5 6 Host Bus Frequency 1 2 3 4 5 6 Frequency Multiplier The SY-5EHM/5EH5 V1.2 Motherboard is designed to support most ® Pentium class processors currently on the market. Jumpers SW1 is used to configure the Motherboard frequency parameters to match the working frequency of your CPU.
- Page 20 Hardware Setup SY-5EHM/5EH5 V1.2 CPU FREQUENCY SETTING (SW1) Configure the SW1 jumpers to the settings that match your CPU speed. Refer to the following tables to set the Frequency Multiplier and Host Bus Frequency of your CPU: Frequency Multiplier Host Bus Frequency Host Bus Multiplier Frequency...
- Page 21 Hardware Setup SY-5EHM/5EH5 V1.2 Please refer to the following table that gives you the correct frequency settings for the specific brand and model of CPU you are installing on this Motherboard. ® Frequency Settings for Intel Processors Processor Frequency Ratio Frequency Setting Clock Clock...
-
Page 22: Hardware Setup
Hardware Setup SY-5EHM/5EH5 V1.2 Frequency Settings for AMD ™ Processors (Continued) Processor Frequency Ratio Frequency Setting Clock Clock Clock Setting: SW1 AMD K5 - PR166 2.5 x 66MHz 66MHz 33MHz 1 2 3 4 5 6 AMD K6 - 166 2.5 x 66MHz 66MHz 33MHz... - Page 23 Hardware Setup SY-5EHM/5EH5 V1.2 Frequency Settings for AMD ™ Processors (Continued) Processor Frequency Ratio Frequency Setting Clock Clock Clock Setting: SW1 AMD K6-2 380 4.0 x 95MHz 63.5MHz 31.75MHz 1 2 3 4 5 6 AMD K6-2 400 4.0 x 100MHz 66MHz 33MHz 1 2 3 4 5 6...
- Page 24 Hardware Setup SY-5EHM/5EH5 V1.2 Frequency Settings for Cyrix ™ Processors (Continued) Processor Rati Frequency Frequency Setting Clock Clock Clock Setting: SW1 Cyrix MX - PR200** 2.0 x 75MHz 75MHz 37.5MHz 1 2 3 4 5 6 Cyrix MX - PR233** 2.5 x 75MHz 75MHz 37.5MHz 1 2 3 4 5 6...
- Page 25 Hardware Setup SY-5EHM/5EH5 V1.2 Frequency Settings for IDT ™ Processors Processor Frequency Ratio Frequency Setting Clock Clock Clock Setting: SW1 IDT X86 CPU 2-233 3.5 x 66MHz 66MHz 33MHz 1 2 3 4 5 6 IDT X86 CPU 2-266 2.33 x 100MHz 66MHz 33MHz 1 2 3 4 5 6 IDT X86 CPU 2-300 2.5 x...
- Page 26 Hardware Setup SY-5EHM/5EH5 V1.2 Step 5. Set JP7,JP9,JP10 for SDRAM frequency JP7 is used to indicate the frequency of the CPU bus clock to the ETEQ chipset. JP9 and JP10 are used to determine that the SDRAM is running at the frequency of the CPU bus clock or the AGP clock.
- Page 27 Hardware Setup SY-5EHM/5EH5 V1.2 Step 6. DRAM Module Installation This Motherboard supports two strips of 72-pin 5V FPM/EDO DRAM (SIMM) from 4 to 64 MB and two strips 168-pin 3.3V/5V Unbuffered DIMM modules from 8 to 256 MB. The Motherboard requires SIMM modules of at least 70ns access time.
-
Page 28: Memory Configuration Table
Hardware Setup SY-5EHM/5EH5 V1.2 12ns or faster DIMM modules; for 83MHz host bus CPUs use 8ns modules. Memory Configuration Table MEMORY SIMM Bank DIMM Banks CONFIGURATION Bank 1,2 DIMM 1 DIMM 2 FPM/EDO/BEDO RAM Type EDO/SDRAM EDO/SDRAM Single RAM 4/8/16/32/64 8/16/32/64/128/256 8/16/32/64/128/256 Module Size (MB) - Page 29 Hardware Setup SY-5EHM/5EH5 V1.2 Step 9. Front Panel Connections Power Keylock Turbo Plug the computer case's front panel devices to the corresponding connectors on the Motherboard. 1. Power LED & KeyLock Plug the Power LED cable into the 5-pin Keylock connector. Some systems may feature a KeyLock function with a front panel switch for enabling or disabling the keyboard.
- Page 30 Hardware Setup SY-5EHM/5EH5 V1.2 3. Speaker Attach the 4-pin PC speaker cable from the case to the Speaker connector on the Motherboard. 4. Turbo LED Connecting the 2-pin Turbo LED cable to the corresponding Turbo LED connector will cause the LED to light whenever the system is in Turbo mode.
- Page 31 Hardware Setup SY-5EHM/5EH5 V1.2 Step 10. External Peripherals Connections External devices such as the keyboard, printer, PS/2 mouse, modem, USB can be connected to the Motherboard. Normally, you can not plug your devices directly onto the Motherboard, except for the keyboard that plugs directly into the back panel KB connector. For other parallel (PRT1) and serial devices (COM1, COM2), first install the external connectors that come with your Motherboard on the computer case, then plug the other end of the flat cable to their...
- Page 32 Hardware Setup SY-5EHM/5EH5 V1.2 1. Serial Ports COM1/COM2 External Devices that use the COM ports include serial mice and modems. The COM port connectors are located on 2 separate brackets panels, as shown on the figure below. Please plug their respective 10 pin flat cable connectors into the COM1 and COM 2 serial port connectors on the Motherboard.
- Page 33 Hardware Setup SY-5EHM/5EH5 V1.2 Parallel Port PRT1 This parallel port is used to connect the printer or other parallel devices. Your Motherboard comes with one 25-pin female external parallel connector with 25-pin flat cable. Plug the 25-pin end of the flat cable into the PRT1 parallel connector on the Motherboard, as shown in the figure below, then fix the bracket to one of the slots at the back of the computer case using a screw.
- Page 34 Hardware Setup SY-5EHM/5EH5 V1.2 PS/2 Mouse Attach the mouse cable to the 6-pin male PS/2 mouse connector on the Motherboard to enable PS/2 mouse function. PS/2 Mouse Connector Connector PRT 1 COM 2 COM 1 Universal Serial Bus (USB) This Motherboard provides a dual-row 10-pin header (one pin is empty) to support two USB ports for your additional devices.
- Page 35 Hardware Setup SY-5EHM/5EH5 V1.2 Step 11. Others Connector Wake-On-LAN (WOL) Attach the 3-pin connector from the LAN card which supports the Wake-On-LAN (WOL) function to the JP44 connector on the Motherboard. This WOL function lets users wake up the connected computer through the LAN card.
- Page 36 Hardware Setup SY-5EHM/5EH5 V1.2 Step 12. CPU Cooling Fan Installation After you have seated the CPU cooling fan properly on the processor, attach the 3-pin fan cable to the JP12 connector on the Motherboard. To avoid damage to the system, install according to the following pin assignment: CPU Cooling Fan: JP12 Step 13.
-
Page 37: Atx Power
Hardware Setup SY-5EHM/5EH5 V1.2 Warning: Follow these precautions to preserve your Motherboard from any remnant currents when connecting to ATX power supply: Turn off the power supply and unplug the power cord of the ATX power supply before connecting to ATX PW connector. - Page 38 Hardware Setup SY-5EHM/5EH5 V1.2 Step 15. CMOS Clearing (JP5) After you have turned off your computer, clear the CMOS memory by momentarily shorting pins 2-3 on jumper JP5, for a few seconds. Then restore JP5 to the initial 1-2 jumper setting in order to recover and retain the default settings.
- Page 39 Hardware Setup SY-5EHM/5EH5 V1.2 Step 17. MULTI I/O ADDRESSES Default settings for multi-I/O addresses are as follows: Port I/O Address Status LPT1 378H ECP + EPP COM1 3F8H COM2 2F8H Warning: If a default I/O address conflicts with other I/O cards such as sound card, you must change one of the I/O addresses to remedy to this address conflict.
- Page 40 Hardware Setup SY-5EHM/5EH5 V1.2 Step 19. Power On You have now completed the hardware installation of your Motherboard successfully. 1. Turn the power on 2. To enter the BIOS Setup Utility, press the <DEL> key while the system is performing the diagnostic checks, Note: If you have failed to enter the BIOS, wait until the boot up sequence is completed.
-
Page 41: Chapter 3 Bios Setup Utility
BIOS Setup Utility SY-5EHM/5EH5 V1.2 Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI/ISA BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. -
Page 42: Save And Exit Setup
BIOS Setup Utility SY-5EHM/5EH5 V1.2 Hot Keys: Function keys give you access to a group of commands throughout the BIOS utility. Function Command Description Help Gives the list of options available for each item. Color Change the color of the display window. Shift F2 Old values Restore the old values. -
Page 43: Standard Cmos Setup
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-1 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] key. ROM PCI/ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm:dd:yy) : Fri, May 29 1998 Time (hh:mm:ss) : 9 : 42 : 43 HARD DISKS TYPE... - Page 44 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-1.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary Setting Description Note (Secondary) Master & Slave Type Auto BIOS detects hard disk type Default automatically.
- Page 45 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-1.4 Video Select the video mode: EGA/VGA (Default), CGA 40, CGA 80, Mono (Monochrome). 3-1.5 Halt On When the BIOS detects system errors, this function will stop the system. Select which type of error will cause the system halt: All Errors (Default), No Errors, All But Diskette, All But Keyboard, All But Disk/Key.
-
Page 46: Bios Features Setup
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-2 BIOS FEATURES SETUP Select the [BIOS FEATURES SETUP] option from the Main Menu and press [Enter] key. ROM PCI/ISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE, INC. Virus Warning : Disabled Video BIOS Shadow : Enabled CPU Internal Cache : Enabled C8000-CBFFF Shadow... - Page 47 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-2.1 Virus Warning Setting Description Note Virus Warning Disabled Default Enabled Enable this option to protect the boot sectors and partition tables of your hard disk. Any attempt to write to them will the system to halt and display a warning message.
- Page 48 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-2.3 System Boot Control Settings System Boot Setting Description Note Control Settings Quick Power On Disabled Self Test Enabled Provides a fast POTS at Default boot-up. Boot Sequence A, C, SCSI Choose the boot sequence adapted to C, A, SCSI your needs, for example: C, CD-ROM, A...
- Page 49 BIOS Setup Utility SY-5EHM/5EH5 V1.2 System Boot Control Settings (continued) System Boot Setting Description Note Control Settings Gate A20 Option Normal Fast Allows RAM access Default above 1MB using the fast gate A20 line. Memory Parity Enabled This allows to perform a Default Check/ ECC redundancy check on the...
- Page 50 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-2.5 Other Control Options Other Control Setting Description Note Options Security Setup Use this feature to prevent Default Option Unauthorized system boot-up or use of BIOS Setup. “Setup”, If a password is set, the password prompt only appears if you attempt to enter the Setup program.
- Page 51 BIOS Setup Utility SY-5EHM/5EH5 V1.2 Other Control Options (Continued) Other Control Setting Description Note Options Video or Disabled Adapter BIOS Enabled Default Shadow The BIOS is shadowed in a 16K segment if it is enabled and if it has BIOS present. These 16 segments can be shadowed from ROM to RAM.
-
Page 52: Chipset Features Setup
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-3 CHIPSET FEATURES SETUP Caution: Change these settings only if you are already familiar with the Chipset. The [CHIPSET FEATURES SETUP] option changes the values of the chipset registers. These registers control the system options in the computer. - Page 53 BIOS Setup Utility SY-5EHM/5EH5 V1.2 CHIPSET FEATURES SETUP CHIPSET Setting Description Note FEATURES Bank 0/1 DRAM FP/EDO Use the default setting Default Timing 70ns Bank 2/3 DRAM Normal Choose DRAM Timing. Timing Medium Bank 4/5 DRAM Fast, Timing Turbo DRAM Read Disabled Pipeline Enabled...
- Page 54 BIOS Setup Utility SY-5EHM/5EH5 V1.2 CHIPSET FEATURES SETUP (Continued) CHIPSET Setting Description Note FEATURES AGP Aperture AGP could use the DRAM Default Size 4-256M as its video RAM. Choose the JDRAM size that you wish to allocate as video RAM. AGP-2X Mode Disabled Default...
-
Page 55: Power Management Setup
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-4 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions. ROM PCI/ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. Primary INTR : ON ACPI function : Disabled IRQ3 (COM2) : Primary Power Management : User Define IRQ4 (COM1) - Page 56 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-4.1 Power Management Controls Power Setting Description Note Management Controls ACPI Disabled Default function Enabled Enabled if you use Windows 98 and want to use ACPI Power User Define Lets you define the HDD and Management system power down times.
- Page 57 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-4.2 PM Timers PM Timers Setting Description Note HDD Power Disable Default Down Some older 1-15Min When the set time has model HDDs elapsed, BIOS sends a may not support command to the HDD to this advanced power down.
- Page 58 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-4.3 PM Events PM Events Setting Description Note Enabled the power managemnet. Default LPT & COM LPT/COM Enabled the power Default management timer. NONE HDD & FDD Enabled the power Default management timers when the event is detected on the Hard Disk Drive and Floppy Disk Drive device.
- Page 59 BIOS Setup Utility SY-5EHM/5EH5 V1.2 PM Events (Continued) PM Events Setting Description Note IRQ# Primary IRQ3(COM2), IRQ4(COM1), IRQ5(LPT2), IRQ6(Floppy Disk), IRQ7(LPT1), IRQ12(PS/2 mouse), IRQ13(Coprocessor), IRQ14(HardDsik) Secondary IRQ9(IRQ2 Redir), IRQ10( Reserved), IRQ11(Reserved) Disabled IRQ8 (RTC Alarm), IRQ15 (Reserved)
-
Page 60: Pnp/Pci Configuration Setup
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-5 PNP/PCI CONFIGURATION SETUP This option sets the Motherboard's PCI Slots. ROM PCI/ISA BIOS PNP/PCI CONFIGURATION SETUP AWARD SOFTWARE, INC. : No CPU to PCI Write Buffer : Enabled PNP OS Installed : Manual PCI Master Broken Timer : Disabled Resources Controlled By : Disabled... - Page 61 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-5.1 PNP/PCI Configuration Controls PNP/PCI Setting Description Note Controls PNP OS Use the default setting Disabled Installed Resources Manual BIOS does not manage PCI/ISA Controlled By PnP card IRQ assignment. Requires to assign IRQ-# and DMA-# to PCI or ISA PnP manually.
- Page 62 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-5.2 PNP/PCI Configuration Setup PNP/PCI Setting Description Note Setup If [Resources Controlled By] is set to [Manual] IRQ-3,4,5,7,9,10, IRQ-# and PCI/ISA PnP Choose IRQ-# and 11,12,14,15 DMA-# DMA-# assigned to DMA-0,1,3,5,6,7 assigned to: PCI/ISA PnP card. IRQ-3,4,5,7,9,10, Legacy ISA Choose IRQ-# and 11,12,14,15...
-
Page 63: Load Setup Defaults
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-6 LOAD SETUP DEFAULTS Select the [LOAD SETUP DEFAULTS] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values. -
Page 64: Integrated Peripherals
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-8 INTEGRATED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGRATED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer. The following screen shows default settings. - Page 65 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-8.1 IDE Device Controls IDE Controls Setting Description Note Onchip IDE Primary Disabled Use the On-board IDE Channel Channel Enabled Default Onchip IDE Second Disabled Turn off the On-board Channel IDE Channel Enabled Default IDE Prefetch Mode Disabled Enabled Enable to enhance...
- Page 66 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-8.2 FDC Controls FDC Controls Setting Description Note Onboard FDC Disabled Turn off the on-board controller floppy controller Enabled Use the on-board Default floppy controller 3-8.3 Onboard Serial Ports Onboard Serial Setting Description Note Ports Onboard UART 1 Disabled Onboard UART 2...
- Page 67 BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-8.4 Onboard Parallel Ports IR Pins Controls Setting Description Note IR Duplex mode Half Select the IR mode Default your IR module Full supports Use IR Pins IR-RX2TX2 Default IR-RX TX 3-8.5 Onboard Parallel Ports Onboard Parallel Setting Description...
-
Page 68: Supervisor Password
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-9 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [BIOS FEATURES SETUP] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a new password or disable the password: Choose [BIOS FEATURES SETUP] in the Main Menu and press [Enter]. -
Page 69: User Password
BIOS Setup Utility SY-5EHM/5EH5 V1.2 Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: Confirm Password: Re-enter your password and then press [Enter] to exit to the Main Menu. This diagram outlines the password selection procedure: ↔... -
Page 70: Ide Hdd Auto Detection
BIOS Setup Utility SY-5EHM/5EH5 V1.2 3-11 IDE HDD AUTO DETECTION This Main Menu function automatically detects the hard disk type and configures the STANDARD CMOS SETUP accordingly. ROM PCI/ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. HARD DISKS TYPE SIZE CYLS HEAD PRECOMP... -
Page 71: Chapter 4 Drivers Installation
HTML format with information on SOYO Motherboards and other products. Step 1. Insert the SOYO CD into the CD-ROM drive The SOYO CD will auto-run, and the SOYO CD Start Up Menu will be shown as below. (SOYO CD Start Up Program Menu) - Page 72 586 boards: 5EH V1.2 Back (Manual Selection Menu) The user's manual files included on the SOYO CD are in PDF (Postscript Document) format. In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system.
- Page 73 After installation of windows, you will need to install the ETEQ drivers. Follow the instruction below. Click the Enter SOYO CD button to display the list of drivers that can be installed on your Motherboard. The start-up program displays the drivers available for the 5EHM/5EH5 V1.2 and the...
- Page 74 (Driver Installation Menu) However, to display the list of all drivers software available with SOYO Motherboards, click the Display all drivers on the SOYO CD button. Please make sure to install only the drivers adapted to your system, or otherwise this may cause system malfunctions.
- Page 75 Note: When the installation is complete, most drivers require to restart your system before they can become active. If you want to see all the drivers available on the SOYO –CD, click the Display all drivers on the SOYO CD button. Do NOT install drivers that are not suitable for your board, otherwise your system may crash.
- Page 76 SOYO-CD and install the next driver. Note: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation program. When the installation is complete, most drivers require to restart your system...
Need help?
Do you have a question about the SY-5EH5/5EHM V1.2 Super 7 and is the answer not in the manual?
Questions and answers