Table of Contents
Advertisement
Advertisement
Chapters
Table of Contents
Summary of Contents for Bully Dog OutLook
- Page 1 INSTALLATION MANuAL Vehicle Application OutLook Part# OutLook Combo# ‘03-’05 Dodge 5.9L Cummins 40266 42500 ‘06 Dodge 5.9L Cummins 40166 41500 ‘03-’07 Ford 6.0 L Power Stroke 40166 41500 ‘01-’05 GM 6.6L Duramax 40366 43500 ‘06 GM 6.6L Duramax 40166 41500...
-
Page 2: Table Of Contents
Mounting Instructions ......................pg. 14 OPERATING INSTRUCTIONS ..............PGS. 15-23 Navigation/Joystick Operation ....................pg.15 Using the OutLook / Selecting the Correct Vehicle ............pg. 15 Vehicle Selection Details ......................pg. 16 ‘06 Dodge Sequence Test ....................... pg. 17 General Display .......................... pg. 18 Main menu / Menu Items .................... -
Page 3: Introduction
You have just purchased the most technologically advanced vehicle monitor available for diesel pickups manufactured by Bully Dog Technologies. The OutLook monitor comes with more user friendly features than any other vehicle monitor in the market place. The OutLook monitor also comes with free technical support, just call: 1-866-285-5936. -
Page 4: Harness Descriptions
Sub-Harness if your truck uses one. Also on the same end as the two green connectors, the OutLook Main harness has two sets of thermocouple wires labeled Pyro 1 and Pyro 2, which can connect to two different pyrometers. -
Page 5: 05 Gm Sub-Harness Installation
Engine Control Unit. On the other end of the ’01- ’05 GM Sub-Harness is a green plug which has male pins and female shell that is used to connect OutLook Main Harness with the female pins and male shell. -
Page 6: Quick Location Overview
OuTLOOK INSTALLATION DODGE HARNESS LOCATION OvERvIEw fire wall FORD HARNESS LOCATION OvERvIEw OutLook with Main Harness IMPORTANT: On FORD applications most of the install takes place inside the cab of the vehicle fire wall fuse box PYRO Harness (to exhaust manifold) - Page 7 OuTLOOK INSTALLATION INSTALLING THE ’01-’05 GM SUB-HARNESS IMPORTANT: Skip these steps if your vehicle is not a ’01-’05 GM In this step you will connect the GM Engine Harness to ‘01-’05 GM Sub-Harness, page 2 #2a. GM ENGINE HARNESS PLUG: 1.
-
Page 8: 05 Dodge Sub-Harness Installation
You may need to replace it when taking the vehicle in for service. 2. Plug the Bully Dog Data Link Plug (that is attached to the sub harness) into the truck’ s data plug receiver. Press the two plugs together until they snap into place. - Page 9 Bully Dog MAP Sensor Plug coming off the ’03-’05 Dodge Sub-Harness into the stock MAP Sensor Plug receiver until they snap together. 2. Plug the stock MAP Sensor Plug into the Bully Dog MAP Sensor Plug receiver on the ’03-’05 Dodge Sub-Har- ness until they snap together.
-
Page 10: Obd Ii Harness Installation
Make sure that the fuse jack is placed on the dead side of the fuse to ensure that the OutLook monitor is protected by the fuse as well. Use a volt meter to verify the dead side of the fuse. With the fuse pulled and the truck powered on but not started, the volt meter should read 0 volts on the fuse jack to ground. -
Page 11: Main Harness Installation
1. For a clean install, first peel-back the weather stripping next to the dash on the driver’ s side door. 2. Set the OutLook Monitor up on the driver’ s side dash and run the OutLook wires down behind the dash to conceal the wiring. -
Page 12: Pyrometer Installation
It is recommended that you mount both a Pre-turbo and a Post-turbo Pyrometer Probe if a vehicle is run- ning more than 50 horsepower over Stock. On the OutLook display screen, Pyro 1 temps are constantly shown in the bottom left quadrant (If you mount Pyro 1 in a Post-turbo location, the numbers in that quadrant will represent Post-turbo). - Page 13 2. Run the Pyro Cable up to engine bay so the end meets the end of Ford Exhaust Manifold the OutLook Main harness and use zip ties to secure the line. 3. Connect the Pyrometer to the OutLook Main harness: if you want...
- Page 14 5/8” wrench. 2. Run the Pyro Cable along the brim of the engine bay so the end meets the end of the OutLook Main Harness and use zip ties Dodge Post-turbo Mount to secure the pyro line. On the Ford Power Stroke & GM Duramax it is easier if you run the pyro cable through the fire wall from the engine bay.
-
Page 15: Mounting Instructions
IMPORTANT: This step is performed on all vehicles. OUTLOOK MONITOR MOUNTING INSTRUCTIONS Bully Dog offers three different options for mounting the OutLook monitor, each lo- cation option places the OutLook monitor in an easily accessed viewing area for the driver. WINDSHIELD MOUNT: 1. -
Page 16: Operating Instructions
One, scroll up and down in the general display to control the vehicle power level. Scroll between Stock, 25%, 50%, 75% and 100%. If using the OutLook with a Triple Dog Downloader, your settings will be Stock, Towing, Perfor- mance and Extreme. -
Page 17: Vehicle Selection Details
• ‘03-’07 6.0L FORD w/BULLy DOG MODULE: Used if you have a ‘03-’07 6.0L Ford Power Stroke along with a Bully Dog Rapid Power or Dyno Dominator plug-in module, a Power Pup Downloader, or Stock. -
Page 18: Dodge Sequence Test
‘06 DODGE CUMMINS: When using the OutLook on the ‘06 Dodge Cummins the first time the OutLook is installed, immediately after the vehicle is selected, the OutLook will undergo a vehicle sequence test. The screens below illustrate exactly what is seen during the test. -
Page 19: General Display
OPERATING INSTRuCTIONS GENERAL DISPLAY Once you have selected a vehicle upon initial use, the OutLook will then bring up the general display screen. Below is an example of the general display screen. It has four quadrants which display vehicle diagnostics and performance tests. - Page 20 SET TOP LEFT DISPLAy: Select this to enter a sub-menu with a list of OutLook Display Options that you select to view in the top left display quadrant of the OutLook Screen. All of the OutLook Display Options are listed in this instruction set with options specific to this make, model, and year of vehicle.
- Page 21 Exhaust Gas Temperatures (EGT’ s ) reach a level greater than or equal to the set level, the OutLook will automatically lower the horsepower and, in turn, bring EGT’ s back down to a safe level. This feature has been designed to save the integrity of an engine by preventing unsafe engine temperatures.
-
Page 22: Pyrometer Probe Defuel
CLEAR PEAK vALUES: This will enable you to erase the peak values that are saved in the OutLook and displayed when you select the View Peak Values main menu op- tion. Clearing the peak values will free up the OutLook to record new values lower than the previously saved peaks. -
Page 23: Outlook Display Options
17. Once you select to display one of the options below, it will be displayed either in the top left, top right, or bottom right quadrant of the OutLook monitor screen. -
Page 24: Injection Control Pressure
When bad starts occur and the test must be restarted, simply press left on the OutLook Joystick and the performance test will restart itself as well as refresh the screen instructions. 1⁄4 MILE TIME: This performance test will display and record how long it takes the vehicle to travel ¼... -
Page 25: Pyrometer Probe Calibration Procedure
IMPORTANT: This step is performed on all vehicles. PYROMETER CALIBRATION PROCEDURE BEFORE THIS STEP CAN BE COMPLETED, COMPLETELY INSTALL THE OUTLOOK AND ALL OF ITS COMPONENTS. 1. Vehicle must be set to Stock HP/TQ levels-meaning no HP/TQ modifications of any kind (downloader or plug-in modules). -
Page 26: Troubleshooting
EGTs Connections Incorrect Make sure that the Pyrometer Probe for the Pre-turbo probe is connected to the Pyro 1 wires on the OutLook Main Harness. The outlook records horsepower and torque from 1/4 mile Horse power & Torque times. -
Page 27: Warranty & Disclaimer
Never exceed recommended vehicle or tire top speed ratings. DISCLAIMER OF LIABILITY Bully Dog Technologies, LLC. Its distributors, jobbers, and dealers (hereafter Seller) shall be in no way responsible for the product’s proper use and service. THE BUYER HERBY WAIVES ALL LIABILITY CLAIMS. - Page 28 Bully Dog Technologies, LLC is a team built on integrity that is dedicated to leading the vehicle performance industry with an uncompromising code of ethics demonstrated in the soundness of its employees, excellent customer service and superior products. UNLEASH THE POWER...
Need help?
Do you have a question about the OutLook and is the answer not in the manual?
Questions and answers