The award-winning Comfee Seat is an innovative, supportive and practical seating system designed specifically for leisure time in the home, school or in respite care. It comes in 3 sizes, with adjustable back height, seat depth and an innovative seat...
6 Safety Information 5. Product Training Record 1. Intended Use The Comfee Seat comes in 3 size options (Clients & Carers) catering for the needs of children and adults Your Leckey product is a prescribed Class with disabilities. As a guide, size 1 is for 1 Medical Device and as such Leckey children aged 4 –...
How to unpack and 6.17 The product is designed for indoor use and when not in use should be stored in a dry place that is not subjected to extremes of temperature. The safe assemble operating temperature range of the product is +5°...
7.1 Attaching the head 7.2 Attaching the 7.3 Attaching the 4 point 7.4 Attaching the tray support with or without Flipaway Chest Laterals pelvic belt speakers Loosen the soft touch knob at top rear Remove top backrest cushion by pulling Remove seatbase cushion by pulling tabs Before you insert the tray, make sure the tray or seat (a).
Page 6
7.7 Attaching the Pommel Cover Slide tray cover on from the rear and snap Put the Comfee Seat into full recline and tilt, Move the calf support into the 90˚position the 2 poppers underneath the tray to secure the armrest in minimum width and maximum for ease of access.
Page 7
7.8 Attaching the Calf 7.9 Attaching the Padded 7.10 Attaching the Support Laterals Footplate Padded Footstraps Remove calf support cushion for ease of For size 1 and 2, slide the centre footplate Unzip the padded footplate cover for ease of access.
Page 8
Fitting 8.1 Fitting the Head 8.2 Fitting the Back Support Cushion with or Support Cushions without Speakers Slide the headrest cover over the headrest Insert the foam into the backrest cushion foam ensuring the contoured section of foam ensuring the profile of the foam is in the is at the top of the cover and the flat section correct position.
Page 9
8.3 Fitting the Seat Base 8.4 Fitting the Flipaway 8.5 Fitting the 4 Point 8.6 Fitting the Calf Cushion Chest Lateral Cushions Pelvic Belt Support Cushion Before fitting the seat base cushion, ensure Slide the flipaway lateral cover over the foam Remove seatbase cushion by pulling tabs Slide the calf support cushion over the the calf support cushion has been fitted...
The clinical setup of the product should be completed by a technically and clinically competent person who has been trained in the use of the product. Leckey recommend that a written record is maintained of all clinical setups for this product.
Page 11
9.1 Headrest With or 9.2 Four Point Pelvic Belt 9.3 Armrests Without Speakers To height adjust the headrest, loosen the soft Remove seatbase cushion by pulling tabs You have a choice of 3 armrest height touch knob at top rear of seat (a) and adjust away from poppers underneath the rear positions.
Page 12
9.4 Seat Depth / Width 9.5 One Piece Backrest 9.6 Two Piece Backrest Fully tilt seat for ease of access. To adjust To adjust the angle on the one piece To adjust the angle on the two piece the depth of the seat base, loosen the 2 backrest, pull the trigger attached to the left backrest, pull the trigger attached to the left knobs below the seat base at either side (a).
Page 13
(a). Pull to the right calf support (a). Pull the lever while adjusting 2 bolts using your Leckey tool (a). Adjust the (The calf support can be adjusted to any and tilt the seat to the required position.
To angle adjust the padded footplate, use / Carers / your Leckey Tool. Locate the bolt underneath the padded footplate inside the slot in the material (b). Adjust the angle by turning the bolt clockwise or anti-clockwise depending on angle required.
Page 15
10.1 Transferring Into and 10.2 Adjusting the 4 Point 10.3 Tilt in Space 10.4 Tray Out of the Comfee Seat Pelvic Harness To prepare the seat for transfer, move the To open and close the 4 point pelvic harness, Locate the lever at the rear of the wooden...
Page 16
To angle adjust the padded footplate, use your Leckey Tool. Locate the bolt underneath the padded footplate inside the slot in the material (b). Adjust the angle by turning the bolt clockwise or anti-clockwise depending on angle required.
Page 17
11 Cleaning & Care 10.8 Padded Footplate 10.9 Flipaway Laterals Information Straps How to Maintain 5. Staining should be removed as quickly To remove padded footplate straps, pull To Flipaway the laterals, pull and hold the When cleaning we recommend that you as possible with absorbent cloth, towels or velcro strip away from the strap.
2. Lift the base to check each castor If in any doubt to the continued safe individually. Make sure they are moving freely use of your Leckey product or if any and remove any dirt from the rubber wheels. parts should fail, please cease using the...
Need help?
Do you have a question about the Comfee Seat and is the answer not in the manual?
Questions and answers