ORDER NO. MTNC020409C1 Service Manual Color Television Main Manual Panasonic Models Chassis CT-13R17B TMB535 CT-13R27W TMB535 CT-13R37S TMB535 This service manual is issued as a service guide for the models listed above. Included in this manual are a set of schematic, block diagrams, functional descriptions, alignment procedures, disassembly procedures and a complete parts list.
CONTENTS CONTENTS ..............................A1-1 Important Safety Notice ..........................A2-1 Service Notes ............................. A2-2, A2-3 GENERAL SPECIFICATIONS ........................A3-1~A3-3 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ......................2. NOTE FOR THE REMOVAL OF THE MAIN PCB ................SERVICE MODE LIST ..........................CONFIRMATION OF HOURS USED ......................
Important Safety Notice Special components are used in this television set which are important for safety. These parts are identified on the schematic diagram by the symbol and printed in BOLD TYPE on the replacement part list. It is essential that these critical parts are replaced with the manufacturer's specified replacement part to prevent X-ray radiation, shock, fire or other hazards.
Service Notes Note: These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose. Leadless Chip Component How to Replace Flat-IC (surface mount)
Page 5
Service Notes (Continued) IMPORTANT: To protect against possible damage to the WARNING: This Receiver has been designed to meet solid state devices due to arcing or static discharge, make or exceed applicable safety and X-ray radiation certain that all ground wires and CTR DAG wire are protection as specified by government agencies and securely connected.
GENERAL SPECIFICATIONS CRT Size / Visual Size 13 inch / 335.4mmV System CRT Type Normal Deflection degree Magnetic Field BV/BH +0.45G/0.18G Color System NTSC Speaker 1Speaker Position Bottom Size 1.5X2.5 Inch Impedance Sound Output 1.0 W 10%(Typical) 0.8 W NTSC3.58+4.43 /PAL60Hz Tuning Broadcasting System System M...
Page 7
GENERAL SPECIFICATIONS OSD Language English French Spanish OSD Language Setting English Clock and Sleep Timer Max Time 120 Min Timer Step On/Off Timer Program(On Tim / Off Tim) Wake Up Timer Timer Back-up (at Power Off Mode) more than G-10 Remote Unit RC-FF...
Page 8
GENERAL SPECIFICATIONS G-12 Accessories Owner's Manual Language English/Spanish W/ Warranty Remote Control Unit Rod Antenna Poles 1Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet...
DISASSEMBLY INSTRUCTIONS INSTALLATION 1. REMOVAL OF ANODE CAP 1. Clean the spot where the cap was located with a small Read the following NOTED items before starting work. amount of alcohol. After turning the power off there might still be a potential voltage that is very dangerous.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Remocon Key Set Key Operations VOL.
ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS 2-1: RF AGC (RF) Read and perform these adjustments when repairing the Place the set with Aging Test for more than 15 minutes. circuits or replacing electrical parts or PCB assemblies. Receive the VHF HIGH (63dB).
Page 12
ELECTRICAL ADJUSTMENTS 2-6: HORIZONTAL PHASE (RF) 2-11: SUB TINT/SUB COLOR (RF, AV) Receive the center cross signal from the Pattern Receive the color bar pattern. (RF Input) Activate the adjustment mode display of Fig. 1-1 and Generator. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "TINT".
ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.
BLOCK DIAGRAM HEAD PHONE JACK J1001 TU001 CHROMA IC CH. UP IC601 M61250FP X602 IC1001 AN7511 3.579545MHz VOL. UP X' TAL AUDIO OUT MICON IC SOUND AMP SP1001 CH. DOWN RF AGC OUT CF601 IC101 OEC7076A SAW FILTER VIF IN (1) VOL.
TV POWER SCHEMATIC DIAGRAM (MAIN PCB) TO SOUND/AV 4A 125V CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, R517_1 D505 REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501) SOUND+B FUSE. SB290S ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME C518 TYPE 4A 125V (F501).
Need help?
Do you have a question about the CT-13R17B and is the answer not in the manual?
Questions and answers