Kontron KTHM65/mITX User Manual
  1. Manuals
  2. Brands
  3. Kontron Manuals
  4. Motherboard
  5. KTHM65/mITX
  6. User manual

Kontron KTHM65/mITX User Manual

Mitx motherboard
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
KTHM65/mITX
KTHM65 Users Guide
KTD-N0838-0
If it's embedded, it's Kontron

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KTHM65/mITX and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Kontron KTHM65/mITX

Summary of Contents for Kontron KTHM65/mITX

  • Page 1 KTHM65/mITX KTHM65 Users Guide KTD-N0838-0 If it’s embedded, it’s Kontron...

  • Page 2: Document Revision History

    Copyright  2011, KONTRON Technology A/S, ALL RIGHTS RESERVED. No part of this document may be reproduced or transmitted in any form or by any means, electronically or mechanically, for any purpose, without the express written permission of KONTRON Technology A/S. Trademark Acknowledgement: Brand and product names are trademarks or registered trademarks of their respective owners.
  • Page 3 KONTRON Technology warrants its products to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, KONTRON Technology will, at its sole option, repair or replace the product with a similar product.

  • Page 4: Table Of Contents

    KTHM65 Graphics Subsystem ....................17 2.5.1 Intel® HD Graphics 3000 ......................17 Power Consumption ........................18 Connector Locations ..............24 KTHM65/mITX – frontside ......................24 KTHM65/mITX – IO Bracket area ................... 25 KTHM65/mITX – backside ......................25 Connector Definitions ..............26 IO-Area Connectors ...............
  • Page 5 KTD-N0838-0 Page 5 Internal Connectors ................ 33 Power Connector (ATX/BTXPWR) ....................33 Fan Connectors (FAN_CPU) (J28) and (FAN_SYS) (J29) ............34 PS/2 Keyboard and Mouse connector (KBDMSE) (J27) ............35 LVDS Flat Panel connector (LVDS) (J20) ................... 36 SATA (Serial ATA) Disk interface (J21 – J26) ................37 USB Connectors (USB) .......................
  • Page 6 KTD-N0838-0 Page 6 11 AMI BIOS Beep Codes..............59 12 OS Setup ..................60 KTHM65 Users Guide...

  • Page 7: Introduction

    The KTHM65 support 2nd generation Intel® i7 -, i5 -, i3 2Core and 4Core processor and the Celeron B810 2Core, see “Processor Support Table for more specific details. The difference between the KTHM65/mITX and the KTQM67/mITX is specified in the following table: Function...

  • Page 8: Installation Procedure

    1 Installation procedure 1.1 Installing the board To get the board running, follow these steps. If the board shipped from KONTRON has already components like RAM, CPU and cooler mounted, then relevant steps below, can be skipped. 1. Turn off the PSU (Power Supply Unit) Warning: Turn off PSU (Power Supply Unit) completely (no mains power connected to the PSU) or leave the Power Connectors unconnected while configuring the board.

  • Page 9: Requirement According To Iec60950

    KTD-N0838-0 Page 9 Installation procedure 1.2 Requirement according to IEC60950 Users of KTHM65 family boards should take care when designing chassis interface connectors in order to fulfil the IEC60950 standard: When an interface/connector has a VCC (or other power) pin, which is directly connected to a power plane like the VCC plane: To protect the external power lines of the peripheral devices, the customer has to take care about: •...

  • Page 10: System Specification

    Page 10 System Specification 2 System Specification 2.1 Component main data The table below summarizes the features of the KTHM65/mITX embedded motherboard. Form factor KTHM65/mITX: miniITX (170,18 mm by 170,18 mm) Processor Support the following 2nd Generation Intel® Core™ (Sandy Bridge M) and Intel®...
  • Page 11 KTD-N0838-0 Page 11 System Specification Video Intel ® i3, i5 or i7 processor supports Intel ® HD Graphics 3000. Intel ® Celeron ® Processor B810 supports Intel ® HD Graphics. Analogue VGA and digital display ports (DVI, 2x DP, LVDS) via the Mobile Intel ® HM65 Chipset.
  • Page 12 Dispose of used batteries according to the manufacturer’s instructions. • BIOS Kontron Technology / AMI BIOS (EFI core version) • Support for ACPI 3.0 ( Advanced Configuration and Power Interface), Plug & Play Suspend (S1 mode)
  • Page 13 Business Equipment Product Category CCN: NWGQ2, NWGQ8 File number: E194252 (Pending) Theoretical MTBF: >268.956 / >131.729 hours @ 40ºC / 60ºC for the KTHM65/mITX Restriction of Hazardous Substances (RoHS): KTHM65 is RoHS compliant. Capacitor utilization: No Tantalum capacitors on board Only Japanese brand Solid capacitors rated for 100 ºC used on board...

  • Page 14: System Overview

    KTD-N0838-0 Page 14 System Specification 2.2 System overview The block diagrams below shows the architecture and main components of the KTHM65. The key ® component on the board is the Intel HM65 (Cougar Point) Mobile Express Chipset. System Specification More detailed: KTHM65 Users Guide...

  • Page 15: Processor Support Table

    CPU’s are indicated by text. Some processors in the list are distributed from Kontron, those CPU’s are marked by an * (asterisk). However please notice that this marking is only guide line and maybe not fully updated. Clock...

  • Page 16: System Memory Support

    KTD-N0838-0 Page 16 System Specification 2.4 System Memory support The KTHM65/mITX has two DDR3 SODIMM sockets.The sockets support the following memory features: • 1.5V (only) 204-pin DDR3 SODIMM with gold-plated contacts • Single/dual rank unbuffered DDR3 1066/1333/1600MT/s (PC3-8500/PC3-10600/PC3-12800) (DDR3 1600 only supported by some i7 processors) •...

  • Page 17: Kthm65 Graphics Subsystem

    KTD-N0838-0 Page 17 System Specification 2.5 KTHM65 Graphics Subsystem The KTHM65 equipped with Intel ® i3, i5 or i7 processor, supports Intel ® HD Graphics 3000. The KTHM65 equipped Intel ® Celeron ® Processor B810, supports Intel ® HD Graphics. KTHM65support analogue VGA and digital display ports (DVI, 2x DP, LVDS) via the Mobile Intel ®...

  • Page 18: Power Consumption

    KTD-N0838-0 Page 18 System Specification 2.6 Power Consumption In order to ensure safe operation of the board, the ATX12V power supply must monitor the supply voltage and shut down if the supplies are out of range – refer to the hardware manual for the actual power supply specification.
  • Page 19 The following four configurations (a – d) have been tested a) Low Power Setup KTHM65/mITX ATX+12V PSU b) Low Power Setup KTHM65/mITX +12V only PSU Standard system configuration equipped with PCIex1 card, Internal graphics, 2x SATA disks, Intel i5 CPU, 1x SODIMM (1GB Modules), Monitor, Keyboard & Mouse. 1x 1-4GB USB Stick, 12V active...
  • Page 20 KTD-N0838-0 Page 20 System Specification a) Low Power Setup KTHM65/mITX ATX+12V PSU DOS Idle, Mean, No external load Current draw Power consumption Supply +12V 0,140 1,680 +12V P4 1,222 14,664 0,411 2,055 +3V3 0,557 1,838 -12V 0,035 0,42 5VSB 0,007...
  • Page 21 KTD-N0838-0 Page 21 System Specification b) Low Power Setup KTHM65/mITX +12V only PSU DOS Idle, Mean, No external load Current draw Power consumption Supply +12V P4 1,721 20,652 Total 20,7 Windows 7, mean 3DMARK2005 ( first scene ) & BiT 6...
  • Page 22 KTD-N0838-0 Page 22 System Specification c) High Power Setup KTHM65/mITX ATX+12V PSU DOS Idle, Mean, No external load Current draw Power consumption Supply +12V 0,932 11,184 +12V P4 1,102 13,224 0,452 2,260 +3V3 0,553 1,825 -12V 0,036 0,432 5VSB 0,007...
  • Page 23 KTD-N0838-0 Page 23 System Specification d) High Power Setup KTHM65/mITX +12V only PSU DOS Idle, Mean, No external load Current draw Power consumption Supply +12V P4 2,499 29,988 Total 30,0 Windows 7, mean 3DMARK2005 ( first scene ) & BiT 6...

  • Page 24: Connector Locations

    KTD-N0838-0 Page 24 Connector Location 3 Connector Locations 3.1 KTHM65/mITX – frontside Sata1 Sata4 Sata2 Sata0 Sata5 Sata3 USB11 (see note below) USB10 USB9 USB13 USB8 USB12 FEATURE System Temperature ATX/ BTXPWR ATX+12V Sensor( Q10) DDR3 0 DDR3 1 FRONTPNL...

  • Page 25: Kthm65/Mitx - Io Bracket Area

    KTD-N0838-0 Page 25 Connector Location 3.2 KTHM65/mITX – IO Bracket area ETH1 USB1 USB3 USB5 USB0 USB2 USB4 DVI-I Audio 3.3 KTHM65/mITX – backside mPCIe1 mPCIe0 KTHM65 Users Guide...

  • Page 26: Connector Definitions

    KTD-N0838-0 Page 26 Connector Definitions 4 Connector Definitions The following sections provide pin definitions and detailed description of all on-board connectors. The connector definitions follow the following notation: Column Description name Shows the pin-numbers in the connector. The graphical layout of the connector definition tables is made similar to the physical connectors.

  • Page 27: Io-Area Connectors

    KTD-N0838-0 Page 27 IO-Area Connectors 5 IO-Area Connectors 5.1 Display connectors (IO Area) The KTHM65 provides one on-board DVI-I port (both digital and analogue), two on-board DP’s (DisplayPort) and one on-board LVDS panel interface. Two graphic pipes are supported; meaning that up to two independent displays can be implemented using any two of the above mentioned graphic ports.

  • Page 28: Dp Connectors (Dp0/Dp1) (J40/J39)

    KTD-N0838-0 Page 28 IO-Area Connectors 5.1.2 DP Connectors (DP0/DP1) (J40/J39) The DP (DisplayPort) connectors are based on standard DP type Foxconn 3VD51203-H7JJ-7H or similar. Signal Description Type Note Lane 0 (p) LVDS Lane 0 (n) LVDS Lane 1 (p) LVDS Lane 1 (n) LVDS Lane 2 (p)

  • Page 29: Ethernet Connector

    KTD-N0838-0 Page 29 IO-Area Connectors 5.2 Ethernet Connector The KTHM65 support one channels of 10/100/1000Mb Ethernet (ETH1), based on Intel® Lewisville 82579LM Gigabit. In order to achieve the specified performance of the Ethernet port, Category 5 twisted pair cables must be used with 10/100MB and Category 5E, 6 or 6E with 1Gb LAN networks.

  • Page 30: Usb Connectors (Io Area)

    KTD-N0838-0 Page 30 IO-Area Connectors 5.3 USB Connectors (IO Area) The KTHM65 board contains two EHCI (Enhanced Host Controller Interface) host controllers that support up to twelve USB 2.0 ports allowing data transfers up to 480Mb/s. Legacy Keyboard/Mouse and wakeup from sleep states are supported. Over-current detection on all fourteen USB ports is supported. The following USB connectors are available in the IO Area.

  • Page 31: Usb Connector 2/3 (Usb2/3)

    KTD-N0838-0 Page 31 IO-Area Connectors 5.3.2 USB Connector 2/3 (USB2/3) USB Ports 2 and 3 are mounted together with DP1 port. Note Type Signal Signal Type Note 5V/SB5V USB3- USB3+ 5V/SB5V USB2- USB2+ Note 1: In order to meet the requirements of USB standard, the 5V input supply must be at least 5.00V. Signal Description USB2+ USB2-...

  • Page 32: Audio Connector (Io Area)

    KTD-N0838-0 Page 32 IO-Area Connectors 5.4 Audio Connector (IO Area) The on-board Audio circuit implements 7.1+2 Channel High Definition Audio with UAA (Universal Audio Architecture), featuring five 24-bit stereo DACs and three 20-bit stereo ADCs. The Following Audio connector is available in IO Area. Audio Speakers, Line-in and Microphone are available in the stacked audiojack connector Signal Type Note...

  • Page 33: Internal Connectors

    Type Note +12V +12V Note 1: Use of the 4-pin ATX+12V Power Connector is required for operation of KTHM65/mITX board. Signal Description P_OK is a power good signal and should be asserted high by the power supply to indicate P_OK that the +5VDC and +3.3VDC outputs are above the undervoltage thresholds of the power...

  • Page 34: Fan Connectors (Fan_Cpu) (J28) And (Fan_Sys) (J29)

    KTD-N0838-0 Page 34 Internal Connectors 6.2 Fan Connectors (FAN_CPU) (J28) and (FAN_SYS) (J29) The FAN_CPU is used for the connection of the FAN for the CPU. The FAN_SYS can be used to power, control and monitor a fan for chassis ventilation etc. The 4pin header is recommended to be used for driving 4-wire type Fan in order to implement FAN speed control.

  • Page 35: Ps/2 Keyboard And Mouse Connector (Kbdmse) (J27)

    KTD-N0838-0 Page 35 Internal Connectors 6.3 PS/2 Keyboard and Mouse connector (KBDMSE) (J27) Attachment of a PS/2 keyboard/mouse can be done through the pinrow connector KBDMSE (J27). Both interfaces utilize open-drain signalling with on-board pull-up. The PS/2 mouse and keyboard is supplied from SB5V when in standby mode in order to enable keyboard or mouse activity to bring the system out from power saving states.

  • Page 36: Lvds Flat Panel Connector (Lvds) (J20)

    KTD-N0838-0 Page 36 Internal Connectors 6.4 LVDS Flat Panel connector (LVDS) (J20) Note Type Signal Signal Type Note Max. 0.5A +12V +12V PWR Max. 0.5A Max. 0.5A +12V +12V PWR Max. 0.5A Max. 0.5A +12V PWR Max. 0.5A Max. 0.5A PWR Max.

  • Page 37: Sata (Serial Ata) Disk Interface (J21 - J26)

    KTD-N0838-0 Page 37 Internal Connectors 6.5 SATA (Serial ATA) Disk interface (J21 – J26) The KTHM65 board has an integrated SATA Host controller (PCH in the HM65 chipset) that supports independent DMA operation on six ports. One device can be installed on each port for a maximum of six SATA devices.

  • Page 38: Usb Connectors (Usb)

    KTD-N0838-0 Page 38 Internal Connectors 6.6 USB Connectors (USB) The KTHM65 board contains two EHCI (Enhanced Host Controller Interface) host controllers that support up to twelve USB 2.0 ports allowing data transfers up to 480Mb/s. Legacy Keyboard/Mouse and wakeup from sleep states are supported. Over-current detection on all fourteen USB ports is supported. The following USB ports are available on Internal Pinrows: USB Port 6 and 7 doesn’t exist.

  • Page 39: Usb Connector 10/11 (Usb10/11) (J11)

    KTD-N0838-0 Page 39 Internal Connectors 6.6.3 USB Connector 10/11 (USB10/11) (J11) USB Ports 10 and 11 are supplied on the internal USB10/11 pinrow connector J11. Note Type Signal Signal Type Note PWR 5V/SB5V 5V/SB5V PWR USB10- USB11- USB10+ USB11+ 9 10 Signal Description USB10+ USB10-...

  • Page 40: Serial Com1 - Com4 Ports (J15, J16, J17, J18)

    KTD-N0838-0 Page 40 Internal Connectors 6.7 Serial COM1 – COM4 Ports (J15, J16, J17, J18) Four RS232 serial ports are available on the KTHM65. The typical definition of the signals in the COM ports is as follows: Signal Description Transmitted Data, sends data to the communications link. The signal is set to the marking state (-12V) on hardware reset when the transmitter is empty or when loop mode operation is initiated.

  • Page 41: Audio Connectors

    KTD-N0838-0 Page 41 Internal Connectors 6.8 Audio Connectors The on-board Audio circuit implements 7.1+2 Channel High Definition Audio with UAA (Universal Audio Architecture), featuring five 24-bit stereo DACs and three 20-bit stereo ADCs. The following Audio connectors are available as Internal connectors. 6.8.1 CDROM Audio Input (CDROM) (J3) CD-ROM audio input may be connected to this connector or it can be used as secondary line-in signal.

  • Page 42: Audio Header Connector (Audio_Head) (J31)

    KTD-N0838-0 Page 42 Internal Connectors 6.8.1 Audio Header Connector (AUDIO_HEAD) (J31) Note Type Signal Signal Type Note LFE-OUT CEN-OUT AAGND AAGND FRONT-OUT-L FRONT-OUT-R AAGND AAGND REAR-OUT-L 9 10 REAR-OUT-R SIDE-OUT-L 11 12 SIDE-OUT-R AAGND 13 14 AAGND MIC1-L 15 16 MIC1-R AAGND 17 18...

  • Page 43: Front Panel Connector (Frontpnl) (J19)

    KTD-N0838-0 Page 43 Internal Connectors 6.9 Front Panel Connector (FRONTPNL) (J19) Pull Ioh/ Ioh/ Pull Note Type Signal Signal Type Note +5V-F +5V-F 9 10 LINE2-L 11 12 25/25mA SATA_LED# 13 14 SUS_LED 15 16 PWRBTN_IN# RSTIN# 17 18 SB3V3 19 20 LINE2-R AGND...

  • Page 44: Feature Connector (Feature) (J30)

    KTD-N0838-0 Page 44 Internal Connectors 6.10 Feature Connector (FEATURE) (J30) Pull Pull Note Ioh/Iol Type Signal Signal Type Ioh/Iol Note CASE_OPEN# SMBC /4mA 10K/ 25/25mA SMBD /4mA 10K/ 25/25mA PWR_OK EXT_BAT PWR FAN3OUT FAN3IN SB3V3 9 10 SB5V GPIO0 11 12 GPIO1 GPIO2 13 14...
  • Page 45 KTD-N0838-0 Page 45 Internal Connectors GPIO in more details. The GPIO’s are controlled via the ITE IT8516F Embedded Controller. Each GPIO has 100pF to ground, clamping Diode to 3V3 and has multiplexed functionality. Some pins can be DAC (Digital to Analogue Converter output), PWM (Pulse Width Modulated signal output), ADC (Analogue to Digital Converter input), TMRI (Timer Counter Input), WUI (Wake Up Input), RI (Ring Indicator Input) or some special function.

  • Page 46: Clear Cmos Jumper (J37)

    KTD-N0838-0 Page 46 Internal Connectors 6.11 Clear CMOS Jumper (J37) The Clear-CMOS Jumper (J37) is used to clear the CMOS content. Jumper (in default position) J37 pin 1 pin1-2 pin2-3 Description Clear CMOS data Default positions Secure CMOS function is disabled and Default values are used Warning: Don’t leave the jumper in position 1-2, otherwise the battery will fully depleted within a few weeks if power is disconnected.

  • Page 47: Spi Recover Jumper (J4)

    KTD-N0838-0 Page 47 Internal Connectors 6.12 SPI Recover Jumper (J4) The SPI Recover Jumper is used to select BIOS Recovery SPI Flash instead of the BIOS Default SPI Flash. Normally Jumper is not installed and board boots on the BIOS Default SPI Flash. Only in case the Default BIOS gets corrupted (board do not boot), then turn off power, install Jumper (J4) and try rebooting.

  • Page 48: Slot Connectors (Pcie, Minipcie)

    KTD-N0838-0 Page 48 Slot Connectors 7 Slot Connectors (PCIe, miniPCIe) 7.1 PCIe Connectors The KTHM65 supports one (x16) (16-lane) PCI Express port, one x1 PCI Express port and two miniPCI Express ports. The 16-lane (x16) PCI Express (PCIe 2.0) port can be used for external PCI Express cards inclusive graphics card.
  • Page 49 KTD-N0838-0 Page 49 Slot Connectors PEG_RXN[4] PEG_TXP[5] PEG_TXN[5] PEG_RXP[5] PEG_RXN[5] PEG_TXP[6] PEG_TXN[6] PEG_RXP[6] PEG_RXN[6] PEG_TXP[7] PEG_TXN[7] PEG_RXP[7] CLKREQ PEG_RXN[7] PEG_TXP[8] PEG_TXN[8] PEG_RXP[8] PEG_RXN[8] PEG_TXP[9] PEG_TXN[9] PEG_RXP[9] PEG_RXN[9] PEG_TXP[10] PEG_TXN[10] PEG_RXP[10] PEG_RXN[10] PEG_TXP[11] PEG_TXN[11] PEG_RXP[11] PEG_RXN[11] PEG_TXP[12] PEG_TXN[12] PEG_RXP[12] PEG_RXN[12] PEG_TXP[13] PEG_TXN[13] PEG_RXP[13] PEG_RXN[13]...

  • Page 50: Minipci-Express Mpcie0 (J34)

    KTD-N0838-0 Page 50 Slot Connectors 7.1.2 miniPCI-Express mPCIe0 (J34) The miniPCI Express port mPCIe0 is located on the backside. Beside miniPCIe cards the mPCIe0 also supports mSATA SSD cards. Note Type Signal Signal Type Note WAKE# +3V3 +1.5V CLKREQ# PCIE_mini CLK# PCIE_mini CLK W_Disable# RST#...

  • Page 51: Minipci-Express Mpcie1 (J35)

    KTD-N0838-0 Page 51 Slot Connectors 7.1.3 miniPCI-Express mPCIe1 (J35) The miniPCI Express port mPCIe1 is located on the backside. (mSATA not supported) Note Type Signal Signal Type Note WAKE# +3V3 +1.5V CLKREQ# PCIE_mini CLK# PCIE_mini CLK W_Disable# RST# PCIE_RXN +3V3 Dual PCIE_RXP +1.5V SMB_CLK...

  • Page 52: Pci-Express X1 Connector (Pcie X1) (J36)

    KTD-N0838-0 Page 52 Slot Connectors 7.1.4 PCI-Express x1 Connector (PCIe x1) (J36) Connector Definitions The KTHM65/mITX supports one PCIe x1. Note Type Signal Signal Type Note +12V +12V +12V +12V +12V SMB_CLK CL_CLK SMB_DATA CL_RST SMB_ALERT +3V3 CL_DATA JTAG_TEST# +3V3...

  • Page 53: On-Board - & Mating Connector Types

    Type no. Manufacturer Type no. FAN_CPU Foxconn HF2704E-M1 1375820-4 (4-pole) FAN_SYS 1470947-1 1375820-3 (3-pole) Molex 22-23-2061 Molex 22-01-2065 KBDMSE Kontron KT 1046-3381 Foxconn HF1104E Molex 50-57-9404 CDROM Molex 70543-0038 Hon Hai LD1807V-S52T Molex 67489-8005 SATA Kontron KT 821035 (cable kit)

  • Page 54: System Resources

    KTD-N0838-0 Page 54 System Resources 9 System Resources 9.1 Memory Map Address (hex) Size Description KTHM65 Users Guide...

  • Page 55: Interrupt Usage

    KTD-N0838-0 Page 55 System Resources 9.2 Interrupt Usage Notes IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 IRQ16 IRQ17 IRQ18 IRQ19 IRQ20 IRQ21 IRQ22 IRQ23 IRQ24 IRQ25 IRQ26 KTHM65 Users Guide...

  • Page 56: Io Map

    KTD-N0838-0 Page 56 System Resources 9.3 IO Map Address range (hex) Size Description KTHM65 Users Guide...
  • Page 57 KTD-N0838-0 Page 57 System Resources KTHM65 Users Guide...

  • Page 58: Bios

    KTD-N0838-0 Page 58 BIOS 10 BIOS This section details specific BIOS features for the KTHM65 family of boards KTHM65 Users Guide...

  • Page 59: Ami Bios Beep Codes

    KTD-N0838-0 Page 59 AMI BIOS Beep Codes 11 AMI BIOS Beep Codes Boot Block Beep Codes: Number of Description Beeps Insert diskette in floppy drive A: ‘AMIBOOT.ROM’ file not found in root directory of diskette in A: Base Memory error Flash Programming successful Floppy read error Keyboard controller BAT command failed...
  • Page 60 KTD-N0838-0 Page 60 OS Setup 12 OS Setup Use the Setup.exe files for all relevant drivers. The drivers can be found on KTHM65 Driver CD or they can be downloaded from the homepage http://www.kontron.com/ KTHM65 Users Guide...

This manual is also suitable for:

Kthm65

Table of Contents