Blata Origami B1 User Manual
  1. Manuals
  2. Brands
  3. Blata Manuals
  4. Motorcycle
  5. Origami B1
  6. User manual

Blata Origami B1 User Manual

Hide thumbs Also See for Origami B1:
Table of Contents

Advertisement

Quick Links

See also: Service Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Origami B1 and is the answer not in the manual?

Questions and answers

Related Manuals for Blata Origami B1

Summary of Contents for Blata Origami B1

  • Page 2 Noise emitted by machinery and equipment (Minibike BLATA ORIGAMI B1) - Measurement of emission sound pressure levels at a work station and at other specified positions. Levels measured by authorized person ( TUV CZ s.r.o.). Test record (no. : 816/90/06/BT/IZ/H) is deposited with producer.
  • Page 3 SAFETY WARNING Always pay attention to the instructions and safety warnings below This manual contains important safety information and instructions which should be read carefully before operating the vehicle. For your own safety and the safety of others follow these rules. Neither manufacturer nor distributor is responsible for injuries caused by unsafe and improper use of the vehicle.

  • Page 4: Table Of Contents

    FRONT AND REAR WHEEL – FIG. 10 ......................8 FRAME – FIG. 11............................9 GLASS BODY COMPLETE – FIG. 12 ......................10 MINIBIKE ORIGAMI B1 - FIG. 5 ........................11,12 ENGINE - BLATA – FIG. 15 .........................13 EXHAUST COMPLETE – FIG. 13........................14 FRONT FORK – FIG. 14 ..........................15 FRONT AND REAR BRAKES - FIG.

  • Page 5: Introduction

    INTRODUCTION The Minibike Origami B1 is designed and built for use on a paved closed circuit track. The track should be clean and without obstacles of any kind. Qualified adults and younger persons can drive the minibike. Children can drive the minibike only under the supervision of a responsible adult person.

  • Page 6: Unpacking And Setting Up Before Riding - Fig. 1

    UNPACKING AND SETTING UP BEFORE RIDING The minibike is delivered in a cardboard carton and packed with folded handlebars and brake levers. After unpacking, set up the handlebars into the position, that suits the best for driving. The maximum pulled brake lever position should not touch on the handlebar grip.

  • Page 7: Starting The Engine - Fig. 2

    Check the tire inflation – 200 kPa (2 bars) or (28 to 30psi) to be commensurate with the driver’s weight. The Tyre pressure should never exceed 2,5 bars, (38psi) in either the front or rear wheel. IMPORTANT NOTICE: If the coolant level rises in the balance tank, switch off the engine immediately! Check the drive of the coolant pump and sealing of the cooling system.

  • Page 8: Periodic Maintenance

    PERIODIC MAINTENANCE Periodic maintenance is the best way to help the machine perform well, give longevity and provide safety and low cost operation. In addition, you will be spared from many worries from self caused problems, resulting from poor maintinence or no maintinence. A - Before every ride: 1.

  • Page 9: Brakes Adjusting - Fig. 4

    ADJUSTING THE BRAKES Small incremental brake adjustment Free play at the handlebar lever is effected by turning the knurled end on the cable adjustor. This will allow the lever to be set at the nominal to ¼ inch of free lever movement. Basic brake adjusting: Screw in the knurled cable adjustor at the brake lever so the cable is in it’s most slack starting position..

  • Page 10: Remove And Refit The Front Wheel

    REMOVE AND REPLACE THE FRONT WHEEL - FIG. 5 Before dismantling the front wheel it is necessary to remove the front brake pads from the front brake, so it is possible to move the brake caliper from the wheel and be able to draw out the wheel and tire. Remove the front axel nut. M10 (920.011.01) Draw out the axel from the fork and wheel.

  • Page 11: Front And Rear Wheel - Fig. 10

    FIG. 10...

  • Page 12: Frame - Fig. 11

    FIG. 11...

  • Page 13: Glass Body Complete - Fig. 12

    FIG. 12...
  • Page 15 OBR. 5...

  • Page 16: Engine - Blata - Fig. 15

    FIG. 15...

  • Page 17: Exhaust Complete - Fig. 13

    FIG. 13...

  • Page 18: Front Fork - Fig. 14

    FIG. 14...

  • Page 19: Front And Rear Brakes - Fig. 7

    FIG. 7...

  • Page 20: Parts List

    340.000.00 MINIBIKE ORIGAMI B1 350.063.00 ENGINE BLOCK GASKET SET ENGINE 350.069.00 CYLINDER- A KIT 120.041.00 STARTER ROPE 350.069.01 CYLINDER- B KIT 310.040.00 HEAD HOLDER SILENT BLOCK 350.069.02 CYLINDER- C KIT 330.001.42 ENGINE COMPLETE 350.069.03 CYLINDER- D KIT 330.002.21 CARBURETOR PHVB 19 350.070.00...
  • Page 21 FOOT PEGS PLASTIC -PAIR 940.008.00 RIVET BULBEX 4.2 x 18.8 WITH CAP 339.012.01 HOSE CLAMP 8/7 950.003.00 WOODRUFF KEY 3e7 x 3,8 349.002.00 DECALS SET ORIGAMI B1 950.008.00 SAFETY LOCK 35 349.004.00 SEAT RUBBER 950.009.00 SAFETY LOCK 17 349.005.00 FOOT REST WASHER 950.018.00...

  • Page 22: Clutch Complete - Fig.6

    FIG. 6 FIG. 16 MP - 1 159.019.00...

  • Page 23: Replacement Of Tire

    REPLACEMENT OF TIRE – FIG. 10 Remove the wheel from the minibike. For the front wheel unbolt the brake disk and for the rear wheel, the brake disk and sprocket. Deflate the tire, by removing the valve stem. Place the wheel on a hard surface and press the tire bead from the wheel rim in to the middle relief at centre of rim.

  • Page 24: Maintenance Of Cooling System

    MAINTENANCE OF COOLING SYSTEM 1. Liquid filling: Place the minibike on the stand. Dismantle the seat and very carefully check all the joints on the hose. For older minibikes do not forget to check for holes and other damages to the hose. To fill the cooler system, 0.5 liters of the coolant is needed.

  • Page 25: Torque Settings

    TORQUE SETTINGS (1 FT-LB = 1.3558 Nm) PART NAME TORQUE SETTING (FT-LB) SECURED BY ENGINE Cylinder head, liquid cooled – M6 Cylinder – nuts M6 Intake manifold – M5 Starter cover – M6 Ratchet wheel –bolt M6 Loctite 243 Magneto (rotor) – nut M10 Starter prowls –...

  • Page 26: Storage Procedures

    Pull the starting rope a couple of times so a film of oil covers and evenly coats the cylinder walls and piston rings. * Long period is 90 days and longer. Rights reserved for technical, text and design changes of the BLATA Company.

  • Page 27: Guarantee List

    It is a great honor for us, that you have chosen our product. We believe that the MINIBIKE will work for you without problems and will bring you much pleasure and fun. The producer of the MINIBIKE is BLATA Company. Manufacturing Number …………………………. CZ Signature of the technical control: ………………………...
  • Page 28 COPYRIGHT BLATA 2007...

Table of Contents

Save PDF