Related Manuals for Syris SY210NT Series
Summary of Contents for Syris SY210NT Series
- Page 1 SYRIS SY210NT Series Quick User Guide Manual Control up to 4 doors with in/out reader Baud rate 2,400 - 115,200 bps Ver : 2.00...
- Page 2 “main menu” and light gray “sub-menu”, please refer the diagram key and the direction of arrow, the function description of sub-menu will be introduce at below document. - 1 - © 2004 by SYRIS Technology Corp.
-
Page 3: Table Of Contents
I t e m Contents Page Attention matter Login/logout steps Setup module (setup reader) Add/delete/edit card Add and delete fingerprint Setup controller ID (when multiple controllers online) Procedure control (setup open door button) - 2 - © 2004 by SYRIS Technology Corp. -
Page 4: Attention Matter
However, in order to confirm the door access security, please execute logout steps after finish setting. Login Step Enter key LCD display Reference MENU System Login Password Wait for password enter 1+2+3+4+EN Master OK Setup light flashes, already in login status - 3 - © 2004 by SYRIS Technology Corp. -
Page 5: Setup Module (Setup Reader)
After install controller and reader, the user needs to setup reader ID and scan communication status from controller (plug & play) to normal transmit the I/O data. The next diagram is System main menu table and the gray part is the step operation range. - 4 - © 2004 by SYRIS Technology Corp. - Page 6 Annotation 3: Card reader ID arrange rule Door Door one Door two Door three Door four Function Incoming reader ID 1 ID 2 ID 3 ID 4 Outgoing reader ID 5 ID 6 ID 7 ID 8 - 5 - © 2004 by SYRIS Technology Corp.
- Page 7 ID repeat cause transmission conflict and can not find the module correctly. Please contact with the Syris technical personnel if confirm the above questions but still can not communicate correctly. - 6 -...
-
Page 8: Add/Delete/Edit Card
Delete card can separate into (Del Card by No.) or (Delete All Card). The next diagram is the Card main menu table and the gray part is the step operation range. - 7 - © 2004 by SYRIS Technology Corp. - Page 9 For example, if card 0015 has been add in advance, when proximity to card 0014, the card number will automatically jump to 0016. - 8 - © 2004 by SYRIS Technology Corp.
- Page 10 SYW95A door access manage software can setup open door mode to “card plus password”. Anti-pass-back (APB Setting): Base on “one in one out” control idea to avoid one card repeat incoming/outgoing situation, mostly apply to parking space management or research centre personnel management. - 9 - © 2004 by SYRIS Technology Corp.
- Page 11 Delete ▼ Delete all card mode All Card Delete Confirm delete or not [No] Delete ▼ Choose Yes [Yes] Delete All cards have been delete Delete Back to item All Card - 10 - © 2004 by SYRIS Technology Corp.
-
Page 12: Add And Delete Fingerprint
“fingerprint control” function. The setting of fingerprint corresponding to card is for one card corresponding to ten fingerprints, out suggestion is to use the Syris fingerprint manage software (SYFPM). In the follow steps, we are going to introduce how to add/delete fingerprint and setup card replace by fingerprint, the next diagram is the Finger Print main menu table and the gray part is the operation range of this step. -
Page 13: Enter Key
Delete ▼ Delete fingerprint mode Finger Delete Delete card by number mode By No Enter the fingerprint number which Finger No：0001 wants to delete Delete The fingerprint has been deleted Finger - 12 - © 2004 by SYRIS Technology Corp. - Page 14 , then press finger on the effective proximity area softly, now the finger tip should parallel with the “ position ceiling”, therefore, the user can also according to the “position ceiling” to locate the fingerprint - 13 - © 2004 by SYRIS Technology Corp.
- Page 15 Ｘ Error: the finger position is too lean on one side and can not be identify - 14 - © 2004 by SYRIS Technology Corp.
- Page 16 (5)The employees data or fingerprint data come from other machine or transmit through Internet, the system didn’t initialize after enroll fingerprint: →Exit the system then re-enter the program to make the system data initialized - 15 - © 2004 by SYRIS Technology Corp.
-
Page 17: Setup Controller Id
When multiple controllers operate online, the ID of each controller needs to setup separately to avoid ID conflict and cause communication abnormality. The next diagram is the System Process main table and the dotted line part is the operation range of this step. - 16 - © 2004 by SYRIS Technology Corp. - Page 18 System MENU Login System ▼＊5 Process APBLevel Setting Control ▼ Setup controller ID item Enter the controller ID number(1~99) Control ID：0001 which wants to assign Control Complete the controller ID setting - 17 - © 2004 by SYRIS Technology Corp.
-
Page 19: Procedure Control
The DO1 of SY210NT-TSN connects to electric lock and the DI1 connects to the open door button. Therefore, the action of press button to open door can be done though the setting of procedure control. - 18 - © 2004 by SYRIS Technology Corp. - Page 20 DI Delay：00 open door signal touch off. Event Event setup complete. Setting Action setup item, setup the action after Action ▼ Setting open door signal touch of. Action - 19 - © 2004 by SYRIS Technology Corp.
- Page 21 Procedure Control(setup open door button) Enter key LCD display Reference Method ▼ Setup action time Time Method Setup time mode [Alway] Method ▼＊２ Choose count by second [Sec] Method Setup time: 003 (three seconds) Time：003 - 20 - © 2004 by SYRIS Technology Corp.
Need help?
Do you have a question about the SY210NT Series and is the answer not in the manual?
Questions and answers