Advertisement
Advertisement
Related Manuals for Kaba SIMPLEX 3000 NARROW STILE
Summary of Contents for Kaba SIMPLEX 3000 NARROW STILE
- Page 1 SIMPLEX ® NARROW STILE Installation Instructions...
-
Page 2: Table Of Contents
E. Resetting an Unknown Combination ........11 Warnings and Cautions Important: Carefully inspect windows, doorframe, door, etc. to ensure that the recommended procedures will not cause any damage. Kaba Access Control’s warranty does not cover damages caused by installation. Caution: Wear safety glasses when preparing door. -
Page 3: Combination Lock Assembly
A. COMBINATION LOCK ASSEMBLY A-1 Cylinder Installation: Remove interposer Partial Rear View of Narrow Stile Lock assembly (A) by removing one round head Assembly screw and one flat head screw (See Figure 1-1). A-2 Install Mortise cylinder by turning Code Plate and Stud Assembly cylinder until cylinder cam (E) contacts lock-in plate (B) (See... -
Page 4: Mounting Lock To Stile
B. MOUNTING LOCK TO STILE B-1 Place combination lock assembly over lock-in studs and slide downward until a stop position is attained (approximately ⁄ " of movement) (See Figure 2-1). The top of the lock housing and drive assembly should be flush when properly positioned. - Page 5 B-2 Fix two each 10-24 x 2 ⁄ " long round head machine screws (A) as shown (See Figures 2-1 & 2-2). Using the DF-59 key, thread the control lock assembly (B) into the combination change sleeve (C) DF-59 (See Figure 2-2) until trim plate is snug against stile.
-
Page 6: Operating Instructions
C. OPERATING INSTRUCTIONS Note: All locks are shipped with the following combination: #2 and #4 pushed at the same time, then #3. For proper security, the factory set code must be changed at the time of installation. Figure 3-1 Gaining Access By Combination Code A. - Page 7 C-4 Latch Holdback A. Insert cylinder key into cylinder on combination lock side of the door. Turn the key in a clockwise direction to the stop position, retracting the latch fully (See Figure 3-6). Hold the key in that position and turn the thumb turn to the left (counterclockwise).
-
Page 8: Warranty
Kaba Access Control warrants this product to be free from defects in material and workmanship under normal use and service for a period of one (1) year. Kaba Access Control will repair or replace, at our discre- tion, Simplex Locks found by Kaba Access Control analysis to be defec- tive during this period. -
Page 11: Combination Change Information
D. COMBINATION CHANGE INFORMATION Important: Read all instructions before beginning. D-1 Changing Combinations: In order to change an existing combination, you must: 1. Have a DF 59 Key 2. Know the existing combination 3. Have lock set for pushbutton access to retract latch 4. - Page 12 D-9 Turn the thumb turn clockwise to the stop position, assuring the latch is retracted (See Figure 4-3). Release thumb turn. You should not be able to turn the thumb turn unless you have depressed the buttons of your newly entered combination. The new combination is now programmed in the lock.
-
Page 13: Resetting An Unknown Combination
Remove the combination chamber, held by 2 screws, from the lock. To remove the 3-sided dust cover marked "Kaba,” “Simplex," etc. place the combination chamber in the position to the right. E-1 Place a small screwdriver on the edge of the... - Page 14 E-13 Look at the code gear pockets (e). The digits in the new combination should not be at the shear line (open position) (See Figure 5-3). Reinstallation: Replace the 3-sided dust cover marked “Kaba,” “Simplex,” etc. Make sure the staked joints on both end plates fit through the slots on the dust cover.
- Page 15 Notes...
- Page 16 Kaba Access Control 2941 Indiana Avenue Winston-Salem, NC 27105 USA Tel: 800.849.8324 or 336.725.1331 Fax: 800.346.9640 or 336.725.3269 www.kabaaccess.com PKG2586 0709...
Need help?
Do you have a question about the SIMPLEX 3000 NARROW STILE and is the answer not in the manual?
Questions and answers