Pixel King Instruction Manual

Instruction Manual
King
Wireless TTL Flash Trigger
For Nikon
Overview
Thank you for purchasing PIXEL product.
Thank you for purchasing Pixel product --- King. King achieves high-sync
flash shooting with Nikon cameras and other creative lighting function
including I-TTL, M, FP ... etc. King supports shutter speeds up to 1/8000 s.
King has 3 different groups; each group can use multiple units and set each
as individual power settings.
Please read this instruction manual completely and ensure proper
operations with your flashgun before using this product.
Cautions
1. Make sure the camera and flash are powered off before installing the
King.
2.
As an electronic accessory this may be affected by rare environmental
causes. Normal working operations should not be affected by this.
3. Drops or shocks will lead to product failure.
4. When not in use for long durations, please turn off the transmitter's and
the receiver's power and remove the battery.
5. The batteries should be installed correctly. Reverse polarity may cause
batteries to leak corrosive liquids, heat or explosion.
6.
When connecting the cable with the device, do not pull directly on the
wires.
7. Do not store in a high temperature, such as an enclosed car under direct
sunlight, the dashboard and other high-temperature areas.
8. Keep dry, do not touch the product with wet hands. Do not immerse in
water or exposed to rain as this may lead to failure of the device.
9.
Do not use near flammable gases. Failure to follow this warning may
cause explosion or fire.
10. This product includes batteries; please strictly follow the instruction for
proper operation. Failure to follow this may cause explosions, fire or
personal injury.
King Basic
Wireless System
System Mode Digital FSK 2.4GHz
Distance Range 100M
Wireless Channel 7
Performance
multi flash
Flash Mode I-TTL、TTL、M ,
1st Curtain, 2nd Curtain, High Speed Sync,
Sync Mode
Red-eye reduction
Group Control 3 different groups (7 different combinations)
King supports flash zooming, focal length, ISO,
Function
shutter speed, FV lock and FP
Sync Speed 1/8000S
Compatible Flash Flashgun, Studio light and outdoor light
Focusing light Transmitter support focusing light
Trigger Mode
Transmitter Output will support PC port and hot shoe trigger
Receiver Output support TTL, Hot shoe and connecting cable socket.
Socket
Transmitter USB socket , PC port , Hot shoe output
Receiver USB socket , PC port , Hot shoe output
Power
TransmitterAA x 2pcs(support 1.2V rechargeable
battery)or DC 5V power
Suitable Battery
ReceiverAA x 2pcs(support 1.2V rechargeable
battery)or DC 5V power
Trans mitter 200Hrs
Standby
Re ceiver 100Hr s
1
Function
Support EV
Support flash group setting on transmitter
Support 1st Curtain, 2nd Curtain and High speed sync
Support High speed sync for studio and outdoor light
Support three flash groups with different flash ratio
Support well known brand flashes for High speed sync and TTL.
Support well known brand flashes for trigger.
(May not support hight speed sync and TTL flash or other function)
Support firmware upgrade
Support multi receiver control
Support flash focusing light
Follow camera instructions for above usage.
Included items
Please check the listed items below in the package, please contact your dealer if there
are missing items.
King Transmitter
King Receiver
PC-1/4 Connecting Cable (6.35mm)
PC-3.5 Connecting Cable
USB 2.0 Cable
Receiver Holder
Universal Flash Holder SF-18
Instruction Manual
PC-3.5 Connecting Cable
PC-1/4 Connecting Cable (6.35mm)
2
Name of each part
Transmitter
{
Channel
Indicator
Operation Indicator
Receiver
{
Channel
Indicator
Operation Indicator
3
Eyelet: Use strap or lanyard to hold the device
Hot Shoe: Hot shoe port for output, airborne flash is available for install
Channel setting button (CH SET): Set the channel of device . Slightly press
the button to check the current status; press again or hold for 2sec to enter
setting mode.
Group setting button (GP SET): Set the group of device. Slightly press the
button to check the current status; press again or hold for 2sec to enter setting
mode.
Channel Indicator/Group Indicator: These indicator lights show the group or
channel working status.
Operation Indicator: Show the statue of power , transmission and output . blue
light will flicking slowly under the stand-by mode ; blue light will flicking quickly
under the Normal transmission ; red light will flicking quickly when under low
power .
Battery Compartment: Compartment for 2pcs AA battery, 1.2V to 1.6V
1pc
1pc
Receiver Lock Ring: Suitable to attach on tripod or screw nut.
1pc
PC Socket: The receiver is the output. It can connect studio light and outdoor
1pc Receiver Holder
flash. The transmitter is the input.
1pc
Power Switch: Switch to OFF to turn off the device; switch to ON to turn on the
1pc
device.
1pc
Transmitter Mounting Foot: Input interface connection with camera hot shoe.
Universal Flash
1pc
Holder SF-18
UBS Socket: Used for firmware upgrade, DC 5V power supply.
Sticker: Showing product S/N number, battery type on the sticker.
4
Group setting
{
Gr oup
button (GP SET)
Indicator
Sticker
Channel setting
Battery Battery button (CH SET)
Compartment Compartment
PC sync socket
USB Socket
Power Switch
Hot Shoe Trigger pin
Mounting Foot
Group setting
{
Gr oup button (GP SET)
Indicator
Sticker Channel setting
button (CH SET)
Battery Battery
Compartment Compartment
PC sync socket
USB Socket
Power Switch
Hot Shoe
Mounting Foot
Eyelet
Eyelet
5
6