Table of Contents
Advertisement
Accenta/Optima User Guide
How to do a Walk Test
Walk around your property, and in turn cause each detector to go into alarm. Also, open and close all door
and windows that are protected by the system. For each detector (including door or window sensor) that is
activated the system will produce a series of beeps, and the associated zone will be indicated on the keypad.
NOTE: Do not test any Personal Attack, Fire or Tamper buttons during the Walk Test since these are still
active and will cause a full alarm.
If any of the tests fail, or you are unsure of the correct procedure, contact your installer
LCD Keypad:
•
Press [PROG] and then enter your code [0][1][2][3]. The
Day LED goes off to indicate that you are in Programming
mode. The first menu Walk Test appears on the screen.
•
Press [SET] or [0]. Zones 1-8 have a zero (0)
below each number.
•
When a zone is successfully tested, number 1
replaces the 0. Zones are added to list as each
one is activated.
•
Press [RESET] to leave the menu or [SET] to
restart the Walk Test.
LED keypad
•
Press [PROG] and then enter your code [0][1][2][3]. The
Day LED goes off and the Tamper (TA) LED comes on to
indicate that you are in Programming mode, Walk Test
•
Press [SET] or [0]. Zones 1-8 are off.
•
When a zone is sucsessfully tested, the LED is on.
Zones are added to list as each one is activated.
•
Press [RESET] to leave the menu or [SET] to restart the
Walk Test.
How to do a Walk Test
0>Walk Test
0>Walk Test
0>Walk Test
0>Walk Test
0>Walk Test
0>Walk Test
0>Walk Test
0>Walk Test
0>Walk Test
0>Walk Test
17
[PROG] then [0][1][2][3]
[SET] or [0]
12345678
12345678
12345678
TP
TP
TP
12345678
12345678
TP
TP
00000000
00000000
00
00
00000000
00000000
00000000
00
00
00
[RESET]
[PROG] then [0][1][2][3]
1 2 3 4 5 6 7 8
ower
Zones
[SET]
4
5
1
2
3
6
[RESET]
4
5
1
2
3
6
Attack
Tamper
Day
7
8
7
8
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Accenta and is the answer not in the manual?
Questions and answers
i can not remember the code
How to set alarm to just enter and exit home. At present the beeps are beeping as I move from alarmed room to room ? I only wish to have alarm on when I exit home.
To set the Honeywell Accenta alarm for entry and exit only (part-set mode):
1. Enter your user code.
2. Press the [PROG] key.
3. The exit tone should stop, and LED indicators for zones 1–3 will light up.
4. Select part-set program [2] or [3] to activate the part alarm.
5. The system will set after a short time.
Note: If there are no exit beeps, Silent Timed Exit mode may be enabled.
This answer is automatically generated
How to set alarm for entry and exit only. The alarm has started to beep in rooms as we move through the house
To set the Honeywell Accenta alarm for entry and exit only (part set mode):
1. Enter your user code (e.g., [0][1][2][3]). The exit beep will start.
2. Press the [PROG] key. The exit tone should stop.
3. Select part-set program [2] or [3] by pressing [2] or [3]. The system will set after a short time.
If the exit tone does not stop after pressing [PROG], the system may not be responding correctly, and you may need to check the configuration or contact your installer.
This answer is automatically generated