Table of Contents
Advertisement
SERVICE MANUAL
Digital Camera
AC adaptor
Contents
1. OUTLINE OF CIRCUIT DESCRIPTION .................... 2
2. DISASSEMBLY .......................................................... 9
3. ELECTRICAL ADJUSTMENT .................................. 12
REGISTRATION ...................................................... 17
5. TROUBLESHOOTING GUIDE ................................. 18
6. PARTS LIST ............................................................. 19
Parts list of optional AC adaptor .............................. 19
Parts list of digital camera ........................................ 19
ACCESSORIES ....................................................... 19
PACKING MATERIALS ............................................ 19
CABINET & CHASSIS PARTS 1 ............................. 20
ELECTRICAL PARTS .............................................. 24
CIRCUIT DIAGRAMS &
PRINTED WIRING BOARDS ...................................... C1
The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of
special significance to product safety. Should any component designated by a symbol need to be replaced, use only the part
designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.
CAUTION : Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.
NOTE : 1. Parts order must contain model number, part number, and description.
2. Substitute parts may be supplied as the service parts.
3. N. S. P. : Not available as service parts.
Design and specification are subject to change without notice.
SX717/U, EX, EX2, EX3, SVA04/U, EX, E, C
PRODUCT SAFETY NOTICE
FILE NO.
VPC-J4
(Product Code : 126 670 01)
(U.S.A., Canada, Korea, Taiwan)
VPC-J4EX
(Product Code : 126 670 02)
(Europe, PAL General)
VPC-J4EXBK
(Product Code : 126 670 05)
(Europe, PAL General)
VPC-J4EXOR
(Product Code : 126 670 06)
(Europe, PAL General)
VAR-G7U
(Product Code : 126 301 15)
(U.S.A., Canada)
VAR-G7EX
(Product Code : 126 301 16)
(Europe, PAL General)
VAR-G7E
(Product Code : 126 301 17)
(U.K.)
VAR-G7C
(Product Code : 126 301 18)
(China)
REFERENCE No. SM5310567
Advertisement
Table of Contents
Related Manuals for Sanyo VPC-J4
Summary of Contents for Sanyo VPC-J4
-
Page 1: Table Of Contents
FILE NO. SERVICE MANUAL VPC-J4 Digital Camera (Product Code : 126 670 01) (U.S.A., Canada, Korea, Taiwan) AC adaptor VPC-J4EX (Product Code : 126 670 02) (Europe, PAL General) VPC-J4EXBK (Product Code : 126 670 05) (Europe, PAL General) VPC-J4EXOR... -
Page 2: Outline Of Circuit Description
1. OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 CIRCUIT DESCRIPTION 1. IC Configuration IC901 (ICX488EQF) CCD imager IC905 (H driver, CDS, AGC and A/D converter) 2. IC901 (CCD imager) [Structure] Interline type CCD image sensor Image size Diagonal 6.67 mm (1/2.7 type) Pixels in total 2396 (H) x 1766 (V) Recording pixels... - Page 3 1-2. CP1 CIRCUIT DESCRIPTION 1. Circuit Description When the TG/SG drives the CCD, picture data passes through 1-1. Digital clamp the A/D and CDS, and is then input to the ASIC as 12-bit The optical black section of the CCD extracts averaged val- data.
- Page 4 1-3. ST1 POWER CIRCUIT DESCRIPTION 1. Outline 4. Digital 1.8 V Power Output This is the main power circuit, and is comprised of the follow- 1.8 V (D) is output. Feedback for the 1.8 V (D) is provided to ing blocks. the switching controller (Pins (9) of IC501) so that PWM con- Switching power controller (IC501) trol can be carried out.
- Page 5 1-4. ST1 STROBE CIRCUIT DESCRIPTION 1. Charging Circuit 2. Light Emission Circuit When UNREG power is supplied to the charge circuit and the When FLCLT signal is input from the ASIC expansion port, CHG signal from microprocessor becomes High (3.3 V), the the stroboscope emits light.
- Page 6 1-5. SYA CIRCUIT DESCRIPTION 1. Configuration and Functions For the overall configuration of the SYA block, refer to the block diagram. The SYA block centers around a 8-bit microprocessor (IC301), and controls camera system condition (mode). The 8-bit microprocessor handles the following functions. 1.
- Page 7 BOOT_COMREQ Boot/command request (Output mode “0” fixing) CARD Card detection (L= card) AVREF ON AD VREF ON/OFF signal (L= ON) PLLEN ASIC PLL oscillation ON/OFF ASIC control signal (ZTEST) ASIC TEST 51~56 SCAN IN5~0 Key scan input 5~0 DC_IN DC adaptor connection detecion (L= DC adaptor) AV_JACK AV JACK connection detection (H= AV JACK detection) Storobe charge detection (input port) (L= ON)
- Page 8 4. Power Supply Control The 8-bit microprocessor controls the power supply for the overall system. The following is a description of how the power supply is turned on and off. When the battery is attached, a regulated 3.2 V voltage is normally input to the 8-bit microprocessor (IC301) by IC302, so that clock counting and key scanning is carried out even when the power switch is turned off, so that the camera can start up again.
-
Page 9: Disassembly
2. DISASSEMBLY 2-1. REMOVAL OF CABINET FRONT, TB2 BOARD AND CABINET BACK 1. Two screws 1.7 x 3 2. Three screws 1.7 x 2.5 3. Two screws 1.7 x 4 4. Cabinet front 5. Connector 6. Screw 1.7 x 2.5 7. - Page 10 2-3. REMOVAL OF LCD AND TB1 BOARD 9. Remove the solder. 1. FPC 10. TB1 board 2. Spacer EL FPC 11. Holder button shutter 3. Connector 12. FPC 4. LCD 13. Two screws 1.7 x 2.5 5. Two screws 1.7 x 2.5 14.
- Page 11 2-4. REMOVAL OF CP1 BOARD AND ST1 BOARD 1. Screw 1.7 x 3.5 2. Holder mic 3. Screw 1.7 x 3.5 4. Connector 5. CP1 board 6. Screw 1.7 x 4.5 7. Remove the solder. 8. Holder flash 9. Screw 1.7 x 4.5 10.
-
Page 12: Electrical Adjustment
3. ELECTRICAL ADJUSTMENT 6. LCD Panel Adjustment 3-1. Table for Servicing Tools 6-1. LCD VcomPP Adjustment Part code 6-2. LCD VcomDC Adjustment Ref. No. Name Number Note: If the lens, CCD and board in item 2-5, it is necessary Pattern box (color viewer) VJ8-0190 to adjust again. - Page 13 3-5. Connecting the camera to the computer 1. Line up the arrow on the cable connector with the notch on the camera's USB port. Insert the connector. 2. Locate a USB port on your computer. To USB port USB cable AC adaptor –...
- Page 14 2. Lens Adjustment 3-6. Adjust Specifications [ST1 board (Side A)] VR501 CL518 Camera Approx. 150 cm 3 cm Siemens star chart Backlight Preparation: lead wire POWER switch: ON TB1 board ST1 board Adjustment condition: power More than A3 size siemens star chart lead wire CN501 Fluorescent light illumination with no flicker...
- Page 15 3. AWB Adjustment 4. CCD White Point Defect Detect Adjustment Preparation: POWER switch: ON Adjustment method: 1. Double-click on the DscCalDi.exe. 2. Select “CCD Defect” on the LCD “Test”, and click the “Yes”. 3. After the adjustment is completed, OK will display. 4.
- Page 16 3-7. Factory Code Setting 1. Check the "Factory Code" display within the Setting group. [CP1 board (Side A)] 2. For models VPC-J4 If "FC_SANYO_U" does not appear, click on the " " mark located on the right of the "Factory Code" display BOX and select "FC_SANYO_U".
-
Page 17: Usb Storage Information Registration
13.) 2. Double-click on the DscCalDi.exe. 3. Click on the Get button in the USB storage window and check the USB storage data. VID: SANYO PID: J4 Serial: Rev. : 1.00 4. -
Page 18: Troubleshooting Guide
5. TROUBLESHOOTING GUIDE POWER LOSS INOPERTIVE TAKING INOPERATIVE SET THE MAIN PUSH SHUTTER SWITCH TO PLAY BUTTON MODE IC301-51, 52 IC301-56 CHECK CHECK S3001 (SCAN IN 4, 5) (SCAN IN0) THE UNIT SWITCH PULSE INPUT PULSE INPUT CN301-34, 35 CHECK IC302-7 4.7 V CHECK ST1, IC955, (P ON, P(A) ON) -
Page 19: Parts List
BATTERY, RECHARGE, LI-ION VAR-G7EX ONLY 645 066 1877 BATTERY CHARGER 645 036 7434 CORD,POWER-1.2MK, VAR-G7E ONLY 645 057 1503 CORD,POWER-1.2MK,EXCEPT VPC-J4 645 065 3506 CORD,POWER-1.29MK, VAR-G7C ONLY 645 057 1510 CORD,POWER-1.9MK,VPC-J4 ONLY 645 068 1332 CORD,POWER-1.29MK, VAR-G7C ONLY 645 065 4831... -
Page 20: Cabinet & Chassis Parts 1
CABINET & CHASSIS PARTS 1 SX717/J Parts List-1 N.S.P.: Not available as service parts. - Page 21 SHIELD TAPE CCD 636 080 5941 ADHESIVE DEC TOP A SX713 636 079 6218 COVER JACK-SX717/EX--3, VPC-J4EXOR ONLY 636 079 3644 COVER JACK-SX717/J,VPC-J4,VPC-J4EX 636 079 4191 COVER JACK-SX717/J---2, VPC-J4EXBK ONLY 636 077 1031 DEC MONITOR-SX717/J 636 077 1017 COVER VF-SX717/J...
-
Page 22: Cabinet & Chassis Parts 2
CABINET & CHASSIS PARTS 2 N.S.P.: Not available as service parts. SX717/J Parts List-2... - Page 23 636 075 7165 SPRING COVER BATT-SX713/J 636 075 6939 HOLDER COVER BATT-SX713/J 636 079 6232 COVER BATTERY-SX717/EX--3, VPC-J4EXOR ONLY 636 077 1024 COVER BATTERY-SX717/J,VPC-J4, VPC-J4EX 636 079 4214 COVER BATTERY-SX717/J---2, VPC-J4EXBK ONLY 636 075 7127 SHAFT COVER BATT-SX713/J 636 076 9403...
-
Page 24: Electrical Parts
ELECTRICAL PARTS Note: 1. Materials of Capacitors and Resistors are abbreviated as follows ; Resistors Capacitors MT-FILM Metallized Film Resistor MT-POLYEST Metallized Polyester Capacitor MT-GLAZE Metallized Glaze Resistor MT-COMPO Metallized Composite Capacitor OXIDE-MT Oxide Metallized Film Resistor TA-SOLID Tantalum Solid Capacitor AL-SOLID Aluminum Solid Capacitor NP-ELECT... - Page 25 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION C1705 403 332 9503 CERAMIC 1U M 6.3V R1053 401 261 5108 MT-FILM 1.0K DU 1/16W C1706 403 401 5801 CERAMIC 10U K 10V R1054 401 225 8503 MT-GLAZE 1.8K JA 1/16W C1707 403 332 9503 CERAMIC...
- Page 26 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION CN181 645 059 0122 PLUG,PWB-WIRE 2P (N.S.P) R9025 401 234 4800 MT-GLAZE 3.3 JA 1/16W (N.S.P) CN301 645 059 0214 SOCKET,FPC 6P (N.S.P) R9027 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) CN951 645 055 5183 SOCKET,FPC 18P (N.S.P)
- Page 27 LOCATION PARTS NO. LOCATION PARTS NO. DESCRIPTION DESCRIPTION LOCATION PARTS NO. DESCRIPTION D5002 407 210 5403 DIODE RB551V-30 R5012 401 261 8703 MT-FILM 22K DD 1/16W D5004 407 210 5403 DIODE RB551V-30 R5013 401 261 9205 MT-FILM 13K DD 1/16W D5006 407 236 0802 ZENER DIODE EDZ2.0B...
- Page 28 SANYO Electric Co., Ltd. Osaka, Japan Mar./’04...