JVC RX-8020VBK Instructions Manual page 58

To change the transmittable signals for
operating a CATV converter or DBS tuner
1. Press and hold CATV/DBS
2. Press CATV/DBS CONTROL.
"CALL" appears on the remote control display window.
3 Enter a manufacturer's code using buttons 1–9,
and 0.
See the following lists to find the code.
4. Release CATV/DBS
The following buttons can be used for operating the CATV
converter and DBS tuner:
CATV/DBS :Turn on and off the CATV converter
CH +/– :Change the channels.
1 – 10, 0, 100+ (+10) :Select the channels.
Note:
Refer also to the manual supplied with your CATV converter or
DBS tuner.
5. Try to operate your CATV converter or DBS
tuner by pressing CATV/DBS
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct
one is entered.
Note:
You cannot preset the signals for both the CATV converter and DBS
tuner at the same time.
For DBS tuner
Manufacturer
JVC
AMSTRAD
BLAUPUNKT
ECHOSTAR
GOLDSTAR
GRUNDIG
HIRSHMANN
INSTRUMENT
ITT/NOKIA
KATHREIN
NEC
ORBITECH
PHILIPS
RCA
SAMSUNG
SCHWAIGER
SIEMENS
SONY
TECHNISAT
55
.
.
or DBS tuner.
The 10 key will function as the
ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
.
Codes
56 , 57, 67
*
43, 44, 45, 46, 47, 48, 49
30
50, 51, 67
31
32, 33
48, 52, 53, 54, 55
68
34
52, 58, 59, 60, 61, 62, 63
35, 36
48
37, 38
65
39, 40
61, 64
41, 42
66
48
*Initial setting
For CATV converter
Manufacturer
GENERAL INSTRUMENT 06, 07, 08, 09, 10, 11,
HAMLIN/REGAL
JERROLD
OAK
PANASONIC
PIONEER
SCIENTIFIC ATLANTA
TOCOM
ZENITH
Manufacturers' codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
To change the transmittable signals for
operating another manufacturer's VCR
1. Press and hold VCR1
2. Press VCR1.
"CALL" appears on the remote control display window.
3. Enter manufacturer's code using buttons 1–9,
and 0.
See the list on the next page to find the code.
4. Release VCR1 .
The following buttons can be used for operating the VCR:
VCR1 :Turn on and off the VCR.
After pressing VCR1, you can perform the following operations
on the VCR:
CH +/– :Change the TV channels on the
1 – 10, 0, 100+ (+10) :Select the TV channels.
3 PLAY
:Start playback.
REW :Rewind a tape.
FF :Fast wind a tape.
7 STOP
:Stop playing or recording.
8 PAUSE:
:Pause playing. To resume press
REC PAUSE
:Enter recording pause by pressing
Note:
Refer also to the manual supplied with your VCR.
5. Try to operate your VCR by pressing VCR1
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Codes
12, 13, 14, 29
01, 02, 03, 04, 05
06, 07, 08, 09, 10, 11,
12, 13, 14
15, 16, 17
18, 19, 20
21, 22
23, 24, 25
26
27, 28
.
VCR.
The 10 key will function as the
ENTER button if your VCR requires
pressing ENTER after selecting a
channel number.
3 PLAY.
this button.
To start recording again, press this
button then 3 PLAY.
.