Related Manuals for Titan TTB426GDO
Summary of Contents for Titan TTB426GDO
- Page 1 Manufacturer's Warranty SAFETY AND OPERATING MANUAL Original instructions POLE PRUNER 750W TTB426GDO...
- Page 2 Congratulations on your purchase of a power tool from Titan Power Tools (UK) Ltd. We want you to continue getting the best performance from it so this handbook includes information on safety, handling and care. Please retain this handbook in case you need to refer to any of the information in the future.
-
Page 3: General Safety Instructions
Damaged or entangled cords increase the risk of electric shock. 5. When operating a garden power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. POLE PRUNER 750W TTB426GDO... - Page 4 6. If operating a garden power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. Personal safety 1. Stay alert, watch what you are doing and use common sense when operating a garden power tool.
- Page 5 When transporting or storing the garden power tool always fit the guide bar cover. Proper handling of the garden power tool will reduce the likelihood of accidental contact with the moving saw chain. POLE PRUNER 750W TTB426GDO...
- Page 6 13. Follow instructions for lubricating, chain tensioning and changing accessories. Improperly tensioned or lubricated chain may either break or increase the chance for kickback. 14. Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery causing loss of control. 15.
- Page 7 3. Stop the engine and unplug from the mains if there are malfunctions. Have the garden power tool checked by a qualified professional and repaired, if necessary, before you put it into operation again. POLE PRUNER 750W TTB426GDO...
- Page 8 VIBRATION The European Physical Agents (Vibration) Directive has been brought in to help reduce hand arm vibration syndrome injuries to power tool users. The directive requires power tool manufacturers and suppliers to provide indicative vibration test results to enable users to make informed decisions as to the period of time a power tool can be used safely on a daily basis and the choice of tool.
- Page 9 Wear ear protection Wear helmet protection Gloves with saw protection Boots with saw protection, steel toecap and non-slip sole Wear protective clothing To avoid potential electric shock, do not use the unit in humid or wet conditions POLE PRUNER 750W TTB426GDO...
- Page 10 Switch off! Remove plug from mains before cleaning or maintenance Switch off! Remove plug from the mains immediately if the cable is damaged or cut. Correct direction of cutting-teeth. Always beware of the danger from overhead electric-power line, keep a safe distance at least 10M from the power line.
- Page 11 Power cord Handle ON/OFF switch Lock-off button Soft grip Pole Locking sleeve for pole extension Pole extension Side cover Cover insert POLE PRUNER 750W TTB426GDO...
-
Page 12: Technical Data
Hex screw Oil tank Oil tank cap Guide bar Saw chain Tension screw Spike bumper Vents Harness 19a Harness attachment 20 Sprocket Rail 22 Tension pin 23 Guide bar protection cover 24 Multi tool TECHNICAL DATA Rated voltage 230-240VAC 50Hz Rated power 750W No-load speed... - Page 13 (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). The sound intensity level for the operator may exceed 85dB(A) and ear protection measures are necessary. ACCESSORIES Harness Saw chain Multi tool POLE PRUNER 750W TTB426GDO...
-
Page 14: Operation Instructions
OPERATION INSTRUCTIONS WARNING! Read all instructions carefully. Do not connect the pole pruner to mains supply power before it is completely assembled. Always use glove s during assembly. 1. ASSEMBLY INSTRUCTIONS Your pole pruner requires installation of the guide bar, saw chain, sprocket cover, adjustment of chain, and filling the oil tank with lubricating oil before it is ready for operation. -
Page 15: Saw Chain Tensioning
The chain life depends mainly upon sufficient lubrication and correct tensioning. POLE PRUNER 750W TTB426GDO... - Page 16 a). Set the power tool on a suitable flat surface. b). Use the screwdriver end of the multi tool to turn the chain tension screw in a clockwise direction until the chain “tie straps” are just touching the bottom edge of the guide bar. The correct chain tension is reached when the chain can be Chain ‘tie straps’...
-
Page 17: Power Connection
Current Device (RCD) with a tripping current of max. 30mA. 1). Use only rubber-insulation-sheath extension cables suitable for outdoor use. The recommended size of extension cord is not lighter than 1.5mm and a maximum of 10meters in length. POLE PRUNER 750W TTB426GDO... -
Page 18: Cable Routing
2). Mains leads on pruner are particularly susceptible to insulation damage. The causes of this include the following: - Cut the cable by passing over it with the pruner. - Damage through crushing if the mains lead is routed under doors or windows. - Cracks caused by ageing of the insulation sheath. -
Page 19: Starting And Stopping
Fully grip both handles at all times during operation. Never operate this pruner using only one hand. Always hold the pruner at an angle of max. 60° from the horizontal level. Otherwise safe operation is not possible. (See Fig.12a) Fig. 12a POLE PRUNER 750W TTB426GDO... - Page 20 2). Never stand directly under the limb you are sawing. Objects may fall different than expected. Always position yourself out of the path of falling limps. Keep other persons away from cutting end of garden power tool and at a safe distance from the work area.
- Page 21 (See Fig.14b) c). Last, cut off the stump with one clean cut from top to Fig. 14a bottom. You might want to seal the cut with a suitable compound. (See Fig.14c) Fig. 14b Fig. 14c POLE PRUNER 750W TTB426GDO...
-
Page 22: Maintenance
MAINTENANCE WARNING! Before carrying out any repairs or servicing work, you must ensure that the pruner has been disconnected from the power supply. Repairs and maintenance work other than described within this instruction manual may be performed only by qualified specialist! 1. -
Page 23: Guide Bar Maintenance
To help minimize wear on the bar, the following guide bar maintenance is recommended. 3). Reinstall the bar, chain (adjust tension), sprocket cover and bar bolt retaining nuts. POLE PRUNER 750W TTB426GDO... -
Page 24: Chain Maintenance
6. CHAIN MAINTENANCE Warning! Unless you have experience and specialized training for dealing with kickback (see Safety Precautions), always use a low-kickback saw chain, which significantly reduces the danger of kickback. Low-kickback saw chains do not eliminated kickbacks completely. A low-kickback or “safety chain” should never be regarded as total protection against injury. -
Page 25: Sharpening Saw Chain
9. ORDERING REPLACEMENT PARTS Please quote the following data when ordering replacement parts: - Type of machine - Article number of the machine - Identification number of the machine - Replacement part number of the part required POLE PRUNER 750W TTB426GDO... -
Page 26: Troubleshooting
TROUBLESHOOTING WARNING! Only perform the steps described in these instructions! All further inspection, maintenance and repair work must be performed by a qualified specialist! Contact a specialist if the problem cannot be solved by yourself! WARNING! Never use tools with defective On/Off switches or defective Kickback brake (Hand Guard). - Page 27 POLE PRUNER 750W TTB426GDO...
-
Page 28: Environmental Protection
ENVIRONMENTAL PROTECTION Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. For further information visit www.recycle-more. co.uk. UK PLUG REPLACEMENT The fuse in the main plug of your garden power tool should always be replaced with one of identical rating. - Page 29 EN61000-3-2:2006 + A1:2009 + A2:2009 EN61000-3-3:2008 Authorised signatory and technical file holder Date: 30/11/11 ISSUE DATE: REV2-MAR12 Signature: Name / title: Peter Harries / Quality Manager Titan Power Tools (UK)Ltd. Trade House, Mead Avenue, BA22 8RT POLE PRUNER 750W TTB426GDO...
- Page 31 POLE PRUNER 750W TTB426GDO...
Need help?
Do you have a question about the TTB426GDO and is the answer not in the manual?
Questions and answers