Konica Minolta bizhub PRO C5500 Solution Manual page 34

bizhub PRO C5500
19. Waste toner packing
20. PFU, LU paper no feed under low temperature environment (J16-02)
21. Gloss unevenness on side2 of coated paper (PFU, LU)
22. SC28-01 to 04 when machine is powered up
23. SC28-31 to 34 (Charging potential correction (Vm) error)
24. White (meandering) line (dust attach on PET sheet)
25. PFU centering error (image suddenly shifts by 5mm)
26. Centering error, skew (how to set paper in PFU)
27. Print job is not accepted while machine indicates dehumidifying
28. Transfer shifts with halftone on thick paper under high humidity
29. Drum drive error C-22xx
30. Depletion of developer after continuous printing
31. Abnormal Image
32. Coupling shaft breakage of transfer belt unit rear side
33. How to perform book printing from Adobe Acrobat (IC-303/IC-305)
34. Calibration procedure
35. C6501 uneven density correction procedure
36. SD-506, tri-fold adjustment procedure
37. How to print on custom size (IC-303/IC-305/IC-408)
38. Rippled uneven image
39. Banding on Halftone
40. Adjustment Procedure at Write Unit Replacement
41. Blurred Characters, toner spray only on black part in color at rear edge, with thick paper
42. How to install IC-304 enhanced driver for Mac
43. IC-304: Custom size is recognized as A4
44. FS-607/520 Main Tray Capacity by Paper Size and Paper weight
45. Copy image orientation changes if using finishing function
46. Paper size list (to feed and to exit)
Note : To view the attached PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Clinton Marquardt, ESS
Solution ID TAUS0701250EN*
Description
How to install system code on the IC-408 through the Ethernet port or USB flash drive.
Solution
ETHERNET LOAD
Version 2.0 systemsoftware or higher can be run directly from the DVD;
1. Disconnect cables from Fiery® and power it down. Power downthe MFP using sub-switch.
2. Double-click on Fiery® Installer.exe.
3. Flip both DIP switches (one inch away from LED display on Fiery® - sometimes covered by gray tape).
4. Approve license screen and Ethernet connection screen.
5. TurnON the Fiery® power switch and wait 15 seconds or so until "FF" is seen on the Fiery® LED (green switch light must be ON). Within 2-3 minutes "1 of
12" will show on installer screen.
6. This will take 35-50 minutes.
7. Once "12 of 12" is done, with status bar not moving and "0KB" visible, click "Finish".
8. Ignore verbiage in installer, power down Fiery® using the AC switch, reset DIP switches to original, then power down the MFP using the main sub-switch.
9. Reconnect normal cables, power up the MFP, then the Fiery® AC switch making sure the green soft-switch light goes ON.
10. At this point it can take the Fiery® up to 60 minutes to complete self-install. When the Fiery® is done the "Controller" button on the MFP LCD is active
and "00" is seen on Fiery® LED.
11. Set up the Fiery® partially through the MFP interface, or via Web Configure (more settings).
Notes :
Video port is totally dead when monitor is connected to Fiery® VGA port.
When Fiery® is booted up, "00" is in LED display.
FLASH DRIVE LOAD
Preparation
PC must have a DVD drive and USB 2.0 port (remove USB devices prior to procedure). According to the manual, 6GB flash drive is minimum size, but a 5GB
drive will work. A 4GB drive may also work, but it has been reported that some features are not loaded as the result of this. BIOS on the PC must be set so
that DVD drive is bootable.
Procedure
1. Put flash tool version 3.11 CDROM into the PC drive and boot to it. Follow prompts to insert system DVD and flash drive; then select language.
2. Continue to follow prompts. DVD contents will copy to flash drive.
3. Load Fiery® with prepared flash drive:
a. PowerOFF sub-switch on the MFP and powerOFF Fiery® AC switch.
Copyright , Konica Minolta Business Solutions U.S.A., Inc.
34
Miscellaneous
Solution Usage 22
March 2010