Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for RAMSET RAM 100
Summary of Contents for RAMSET RAM 100
- Page 1 RAMSET www.ramsetinc.com...
-
Page 2: Table Of Contents
Classes of Vehicular Gate Operators ....................4 General Specifications........................5 RAM 100 Installation Specifications ....................6 RAM 100 Front Installation/ Foot Pedal Release ................7 RAM 1000/ RAM 5500 Installation Specifications ................8 RAM 1000/ RAM 5500 Types of Installations ..................9 Loop Sensor Installation/ Gate Travel Adjustment ................10 Pushbutton Controls &... -
Page 3: Responsibilities Of Installers And Technicians
• MAKE SURE TO ELIMINATE ANY PINCH POINTS ExISTING ON THE INSTALLATION. (ie. ROLLERS, ARMS…etc. ) • RAMSET GATE OPERATORS MUST BE INSTALLED BY A TRAINED TECHNICIAN. SAFETY DEvICES • REMOVE OR PROTECT ALL PINCH POINTS FROM THE GATE OPERATOR. -
Page 4: Important Safety Requirements By Ul Standards
RAMSET IMPORTANT SAFETY REQUIREMENTS BY UL STANDARDS Prior to installation, the following must be g) The stop and/or reset button must be located in the line- observed: (per UL 325.56.8.4). of-sight of the gate. Activation of the reset control shall not cause the operator to start. -
Page 5: Classes Of Vehicular Gate Operators
RAMSET CLASSES OF vEhICULAR GATE OPERATORS vehicular horizontal slide-gate operator (or system) - A vehicular gate operator (or system) that controls a gate which slides in a horizontal direction that is intended for use for vehicular entrance or exit to a drive, parking lot, or the like. -
Page 6: General Specifications
Do not exceed the specifications. The warranty on your unit will be void if the WARNING installation exceeds the recommended specifications. Note: Model RAM 100 Note: is designed to be Model RAM 1000 and RAM 5500 can be installed only for used for center and rear installation with front installations. -
Page 7: Ram 100 Installation Specifications
RAMSET RAM 100 INSTALLATION SPECIFICATIONS Do not exceed the specifications. The warranty on your unit will be void if the WARNING installation exceeds the recommended specifications. All Sliding Gate Operators are factory preset GATE for (LH) Left Hand Installations. Figure 1 CONCRETE PAD CONSTRUCTION 3”... -
Page 8: Ram 100 Front Installation/ Foot Pedal Release
RAMSET RAM 100 FRONT INSTALLATION FRONT INSTALLATION Figure 4 GATE SHOWN Closed Tail on gate required TAIL WALL 13 7/8” 5 3/4” 6” min FOOT PEDAL RELEASE We do not recommend use of the foot pedal on installations with steep inclines. Always make sure the gate is secured when using the foot pedal to avoid sudden movements from the gate. -
Page 9: Ram 1000/ Ram 5500 Installation Specifications
RAMSET RAM 1000/ RAM 5500 INSTALLATION SPECIFICATIONS Do not exceed the specifications. The warranty on your unit will be void if the WARNING installation exceeds the recommended specifications. All Sliding Gate Operators are factory preset Figure 6 for (LH) Left Hand Installations. -
Page 10: Ram 1000/ Ram 5500 Types Of Installations
RAMSET RAM 1000/ RAM 5500 TYPES OF INSTALLATIONS FRONT INSTALLATION Figure 9 GATE SHOWN Closed Tail on gate required Inside Property TAIL Outside Property CENTER INSTALLATION Figure 10 GATE SHOWN Fully Open No tail on gate required Inside Property Top View... -
Page 11: Loop Sensor Installation/ Gate Travel Adjustment
RAMSET LOOP SENSOR INSTALLATION Ramset Gate Operators should always be installed with non-contact sensing devices such as Loop Detectors, Photo Eyes or the equivalent. A non-contact sensor (photoelectric sensor or equivalent) and a contact sensor (edge device or equivalent) is required on each individual installation to comply with UL325. -
Page 12: Pushbutton Controls & Master/Slave Installation
RAMSET PUShBUTTON CONTROLS Three pushbuttons are located under the dip switches for operation of the gate (see Figure 15). The opening, stop and closing buttons can be utilized to set limit switches and verify proper system operation when installing or servicing an operator. -
Page 13: Dip Switch Configuration
RAMSET DIP SWITCh CONFIGURATION Figure 17 “Intelligate” Control Board DIP SWITCH “A” Dip Switch “A” 1, 2 & 3; Dip Switch “B” 2; “PRE WARN” AUTOMATIC TIMER TO CLOSE GATE Used with jP2 “Relay Connections”: pins 7 & 8. ‘0’ is “OFF”... -
Page 14: Dip Switch Configuration
RAMSET DIP SWITCh CONFIGURATION DIP SWITCH “C” Dip Switch “C” 1; “SECURE CLOSE” Dip Switch “C” 5; “CLOSE DELAY” Function: One second delay on the closing of the gate. OFF Normal Operation Dip Switch “C” 6; “OPEN DELAY” When power is lost, then regained, control board checks status of the gate. -
Page 15: Terminal Strip Connections
RAMSET TERMINAL STRIP CONNECTIONS Figure 18 Radio Receiver Limit Switches www.ramsetinc.com... - Page 16 RAMSET normal operation. If triggered twice before TERMINAL STRIP CONNECTIONS reaching a limit switch, the alarm will sound for Terminal # 1 - COMMON: 6 minutes and the control board will not accept Low voltage common. any commands. After the 6 minutes the 24 VDC is...
-
Page 17: Ramset "Intelligate" Control Board
RAMSET RAMSET “INTELLIGATE” CONTROL BOARD Introduction: Ramset’s “Intelligate” Control Board works VAC and 220 VAC single-phase applications. with Sliding, Swinging and Overhead vehicular Some of the functions of the Control Board gate operators. It is controlled by a program- are: 0 - 60 seconds automatic close timer, self mable microprocessor that reads and precisely adjusting E.R.D. -
Page 18: Wire Board Connections
Use with ILD-24s, Loop wires should be connected to this plug. jP4, jP5 & jP8 - Reverse, Exit & Phantom Sensor: Used with the Ramset ILD-24 plug-in loop detector. The Loop wires should be connected into the “LOOP INPUTS” plug. www.ramsetinc.com... -
Page 19: Ram 100 Parts Diagram
RAMSET PARTS DIAGRAM RAM 100 Figure 20 www.ramsetinc.com... -
Page 20: Ram 1000/ Ram 5500 Parts Diagram
RAMSET PARTS DIAGRAM RAM 1000 • RAM 5500 Figure 21 www.ramsetinc.com... -
Page 21: Bill Of Materials
RAMSET bill of MAteRiAls foR: RAM 100 • RAM 1000 • RAM 5500 ITEM PART # PART DESCRIPTION RAM 100 RAM 1000 RAM 5500 800-00-00 Chassis - Ram 100 800-00-01 Chassis - Ram 1000/5500 800-02-03 Gear Reducer - Size 43, Ratio 30:1 (C-Face) -
Page 22: Bill Of Materials
RAMSET bill of MAteRiAls foR: RAM 100 • RAM 1000 • RAM 5500 ITEM PART # PART DESCRIPTION RAM 100 RAM 1000 RAM 5500 FOOT PEDAL RELEASE ASSEMBLY - RAM 100 800-75-20 800-06-11 Sprocket, Clutch Release - 41B21H 800-22-00 Spring - 1 1/4" x 1 1/4"... -
Page 23: Gate Entrance Safety Precautions
RAMSET GATE ENTRANCE SAFETY PRECAUTIONS WARNING Not following these instructions may cause severe injury or death to persons IMPORTANT SAFETY INSTRUCTIONS 1. Never let children operate or play with gate con- trols. Keep the controls away from children. 2. The entrance is for vehicles only. Pedestrians should use a separate entrance. -
Page 24: Important Information For The Homeowner
E.R.D. and battery back warranty extension card. Return the warranty card, up systems. via certified mail, to Ramset within 90 days of purchase: Warning signs must be placed on every gate in a highly visible area. -
Page 25: Troubleshooting Table
1. Faulty accessory connected “REv LOOP” L.E.D. plug-ins, using the “Rev Loop” input. ALWAYS ‘ON’. to the “Rev Loop”. If problem persist, contact Ramset. 1. Check all transmitters. 1. Stuck button on Transmitter “RADIO” L.E.D. ALWAYS 2. Remove receiver. ‘ON’. - Page 26 9116 De Garmo Ave. Sun valley, CA 91352 tel: (818) 504-2533 • fax: (818) 504-1141 www.ramsetinc.com...
Need help?
Do you have a question about the RAM 100 and is the answer not in the manual?
Questions and answers
Where is the :Learn" or "Program" button on a Ramset model 100UL gate opener?
how to install replacement motor
To install a replacement motor for the RAMSET RAM 100:
1. Power Off – Disconnect the power supply to ensure safety.
2. Remove the Old Motor
- Use the foot pedal release to disengage the gate from the motor.
- Detach the motor from the chassis by removing the mounting bolts.
- Disconnect the wiring from the control board.
3. Install the New Motor
- Position the replacement motor (C-Face, 120 VAC, 1/2 HP) in place.
- Secure it with the mounting bolts.
- Connect the wiring as per the original configuration.
4. Reassemble and Test
- Re-engage the gate with the motor.
- Restore power and test the motor operation.
- Ensure smooth and quiet functionality.
Follow all safety guidelines and do not exceed installation specifications.
This answer is automatically generated
how to program remote control