Related Manuals for Optium Xceed
Summary of Contents for Optium Xceed
-
Page 1: Table Of Contents
Table of Contents Welcome Important Things to Know about Your Optium Xceed Diabetes Monitoring System Intended Use How Your Optium Xceed Diabetes Monitoring System Works Optium Xceed Kit Contents Getting to Know Your Meter’s Features Setting Up Your Optium Xceed Meter 7 Buttons to Use Setup Options How to Set the Beeper, Date, Time, & View... - Page 2 Doing A Control Solution Test Why Do A Control Solution Test? When Is Doing A Control Solution Test Recommended? Important Information about Control Solution Testing What You Will Need How to Do Control Solution Testing Understanding Your Result Reviewing & Using Your Results What Can Your Meter Show You? How to See Results in Memory How to See Averages Transferring Your Results to A Computer...
-
Page 3: Welcome
Welcome Thank you for choosing the Optium™ Xceed ™ Diabetes Please contact your local Abbott Diabetes Care office or distributor with any questions you may have about the Monitoring System. Optium Xceed Diabetes Monitoring System (please see Important steps for using the System are inside this guide. page 57 for Customer Support phone numbers). If you Please read it carefully. cannot reach your local office or distributor, contact your Your new Optium Xceed Diabetes Monitoring System is healthcare professional. an important tool that can help you better manage your diabetes. The System measures both blood glucose (sugar) Please read the following items before using your Optium and blood β-Ketone. Blood glucose and blood β-Ketone Xceed Diabetes Monitoring System: results can help you understand your diabetes and what • User guide happens with: • Blood glucose test strip instructions for use • Food • Blood β-Ketone test strip instructions for use • Exercise • Lancing device instructions for use and other information • Stress and illness • Warranty card • Diabetes medications Always monitor your blood glucose and blood β-Ketone according to your healthcare professional’s recommendations. -
Page 4: Intended Use
Optium Xceed User’s Guide • Is for monitoring glucose in fresh whole – Contains system information and directions. blood (for example, from the fingertip). • Carrying Case Is for monitoring β-Ketone in fresh whole – Use this to store and carry your meter and other monitoring blood from the fingertip. supplies. • Measures β-hydroxybutyrate (β-Ketone), the most important of the three ketone bodies Your kit may also contain: circulating in the bloodstream. Optium Xceed Quick Reference Guide • Is for use only with Optium™ Blood Glucose Test Strips and – Gives the basic steps to calibrate your meter and monitor Optium™ Blood β-Ketone Test Strips. your blood glucose. • Optium™ and Optium™ POC Blood Glucose Test Strips are Logbook different. Please refer to your test strip instructions for use – Use this to record your test results, activities, and medications. for important information about sample types that may be Limited Warranty Card used with these test strips. – Please fill this out and return to the address provided to start •... -
Page 5: Getting To Know Your Meter's Features
Getting to Know Your Meter’s Features Strip Port This is where you insert: Display Backlight • Window Button A blood glucose test strip. Display Window Back • A blood β-Ketone test strip. Button This shows: • A glucose calibrator. • Blood glucose and blood • A ketone calibrator. β-Ketone results. • • Data cable (not included) for uploading Glucose and β-Ketone results to a computer. LOT numbers. • Previous test results and Mode Button error messages. Mode Strip Forward • Use this button to: Blood glucose averages. Button Port Button •... -
Page 6: Setting Up Your Optium Xceed Meter
CHAPTER 2 Questions? Call Setting Up Your Optium Set Date Format Customer Support: Xceed Meter In "Set Date Format", you choose how the month and See page 57. day show on the meter’s display window. Buttons to Use Measurement Units Mode Button. Blood glucose measurement units are factory-set in mg/dL Forward Button. or mmol/L. Back Button. Blood β-Ketone measurement units are in mmol/L only. Setup Options How to Set the Beeper, Date, Time, & View Measurement Units Set Beeper To begin, pull the battery tab out. Your... -
Page 7: Set Time
To turn your meter ON, Press and Minutes: Hold the button. The Minutes flash on and off. The beeper ON message shows on the display window. The musical Press and Release the button to notes flash on and off, and the move the minutes forward. meter beeps. If you go past the correct minute, Press To change the beeper setting, Press and Release the button to move the and Release the button or the minutes back. button once. Press and Release the button to save the minutes and to move to Set Date. Press and Release the button to save the beeper setting and to move to Set Time (Hour). -
Page 8: Set Time Format
Set Time Format Month: Choice #1 The Month flashes on and off. You have two choices: Choice #1: For the 12-hour format, AM Press and Release the button to or PM shows. move the month forward. Choice #2: For the 24-hour format, AM If you go past the correct month, or PM does not show. Press and Release the button to move the month back. To change the Time Format, Press and Release the button or the Press and Release the button to save button once. the month and to move to Set Day. Press and Release the button to save the Time Format and to move Choice #2 to Set Date Format. Set Date Format Day: Choice #1 You have two choices: The Day flashes on and off. Choice #1: For the month-day format, Press and Release the button to "-" shows with the date. -
Page 9: Blood Glucose Measurement Units
CHAPTER 3 Questions? Call Blood Glucose Calibrating Your Optium Customer Support: Measurement Units See page 57. Xceed Meter Consult your healthcare professional Why Calibrate Your Meter? if you have any questions about the Your Optium Xceed meter must be calibrated so that it can blood glucose measurement units. recognize the test strip you are using. Calibration ensures that your results are accurate. This screen shows the blood glucose When to Calibrate Your Meter measurement units (mg/dL or mmol/L). • When you use the meter for the first time. • Press and Release the button to EACH time you open and use a new box of blood glucose return to Set Beeper. or blood β-Ketone test strips. What You Will Need Press and Hold the button to turn • your meter off. Optium Xceed meter. • For glucose calibration: - Blood glucose test strip. - Blood glucose test strip instructions for use. - Page 10 IMPORTANT: Use only the calibrator that is packaged in Check that the LOT number on all these items matches: the box of test strips you are using. ✓ Display window ✓ Test strip calibrator Do not use test strips that have expired. Check the ✓ Test strip instructions for use ✓ Test strip foil packet expiration date on the test strip foil packet and test strip When the LOT number on all these box. If only the year and month are shown, the expiration items matches: date is the last day of the month. What It Means: Remove the glucose or β-Ketone calibrator package Calibration is complete. from the new box of test strips. What to Do: You may now monitor your blood glucose or Open the calibrator package. Find the blood β-Ketone. three raised bumps on the calibrator package. Peel the clear cover away from When the LOT number on all these items the three raised bumps.
-
Page 11: How To Recall The Lot Number
Questions? Call How to Recall the LOT Number Monitoring Your Blood Glucose Customer Service. To recall the glucose LOT number, Press and Hold the See page 57. button. While holding the button, Press and Hold the button. The Display Check shows on the What You Will Need display window, then the glucose • LOT number shows with the Blood glucose test strip with its instructions for use. • time, month, and day of the most Optium Xceed meter calibrated to match the LOT number recent glucose calibration. of the blood glucose test strip you are using. • Lancing device and a new, sterile lancet. After the glucose LOT number is displayed, you can Important Information about Monitoring Your recall the β-Ketone LOT number. Press and Release the Blood Glucose button or the button. • Do not use out-of-date test strips. Check the expiration The β-Ketone LOT number shows date printed on the test strip box and on each test strip foil "CODE", the time, month, and day packet. If only the month and year... -
Page 12: How To Monitor Your Blood Glucose
• How to Monitor Your Blood Glucose Time, month, and day (if set) Getting Started If date and time are not set, dashes will show instead of numbers. Prepare your lancing device. Wash your hands using warm soapy water and dry them completely. Remove the test strip from its foil packet. • LOT number for the box of blood glucose test strips you are using. Note: For pictures that show how to open the blood glucose test strip foil packet, please see the information card in the box of blood glucose test strips. Insert the three black lines at the end • of the test strip into the strip port. Apply Sample message, which tells you that the meter is ready for you to apply blood to the blood glucose test strip. Push the test strip in until it stops. The meter turns on automatically. These items show on the display window, one after the other: • Display Check – Remember to make sure that all items in the picture here show on the display window. (See Chapter 1 for more information about the Display Check.) ART10825-Rev-A-Man.indd 22-23 11/10/06 1:09:35 PM... - Page 13 Lancets and Lancing Device Obtaining A Blood Drop • Use your lancing device to obtain a blood drop. Lancets are for one-time use only. Use a new lancet each time you monitor. Recommendations for Obtaining a Blood Drop • Discard your used lancet properly. Put it in an • To obtain a sample from an alternative site (forearm, empty puncture-resistant container, such as a upper arm, or base of the thumb), use an plastic milk carton or detergent bottle. appropriate alternative site lancing device. • Never share your lancing device or lancet with another person. Fingertip sampling Applying the Blood Drop to the Test Strip • Before you obtain a blood sample from the fingertip, forearm, upper arm, or base of the Touch the blood drop to the white area thumb, make sure the sample site is at the end of the test strip. The blood is clean, dry, and warm. To warm the drawn into the test strip. sample site, wash it in warm water, rub the skin vigorously for a few seconds, or apply a warm pad to it. Note: If the meter shuts off before you apply Forearm sampling blood to the test strip, remove the test strip from the meter and try again. • Continue to touch the blood drop to the end of Hang your arm down before pricking the test strip until the meter begins the test. The your finger or the base of the thumb to...
-
Page 14: Understanding Your Result
Shutting Off Your Meter IMPORTANT: If the countdown does not start: Removing the test strip from the strip port turns off the What It Means: meter. You can use the opened foil packet to remove Correct and discard your used test strip. You might not have applied ✔ enough blood to the test strip. What to Do: Discard the test strip properly. • Apply a second drop of blood to the test strip. Refer to your test strip Note: You may also turn the meter off by Pressing instructions for use for the number and Holding the button. If you do not turn your of seconds you have to apply a meter off or pull the test strip out, the meter shuts off second drop. automatically after 60 seconds. • If the countdown still does not start, or if the number of seconds you have to apply a second drop have Understanding Your Result passed, discard the test strip, turn off your meter, and try again with "LO" Result a new test strip. What It Means: Your meter has determined that your blood glucose result is lower than 20 mg/dL (1.1 mmol/L) At the end of the countdown: or there may be a problem with the test strip. • What to Do: If the beeper is ON, listen for the beeper. - Page 15 Result 300 mg/dL or Higher "E4" Result When your blood glucose result is 300 mg/dL What It Means: (16.7 mmol/L) or higher, KETONES? flashes on Your meter has determined that your and off on the display window. blood glucose may be too high to be read by the system, or there may be a problem What to Do: with the test strip. If you check your ketones as part of your What to Do: diabetes management program, it is Monitor your blood glucose again with a new recommended that you check your test strip. If E4 shows on the display window again, blood β-Ketone. contact your healthcare professional immediately. "HI" Result IMPORTANT: It is recommended that you repeat the blood glucose test What It Means: with a new test strip when: • Your meter has determined that your LO shows on the display window. • blood glucose result is higher than You obtain a low blood glucose result, but you do not have 500 mg/dL (27.8 mmol/L) or there symptoms of low blood glucose. • may be a problem with the test strip. Your meter displays a blood glucose result that is unusually low, lower than 50 mg/dL (2.8 mmol/L). What to Do: •...
-
Page 16: Monitoring Your Blood Β-Ketone
• the test strip. The test strip operating range is in the “What else Your blood glucose is do I need to know?” section of your blood β-Ketone test strip higher than 300 mg/dL (16.7 mmol/L). instructions for use. • You are experiencing unusual blood glucose results. • Read the lancing device instructions for use. • You and your healthcare professional determine that it is necessary. What You Will Need • Blood β-Ketone test strip with its instructions for use. • Optium Xceed meter calibrated to match the LOT number of the blood β-Ketone test strip you are using. • Lancing device and a new, sterile lancet. Important Information about Monitoring Your Blood β-Ketone • For more detailed information about your blood β-Ketone test strip, please refer to its instructions for use before monitoring. • Do not use out-of-date test strips. Check the expiration date printed on the test strip box and on each test strip foil packet. • Do not put urine on the L O T 13758 blood β-Ketone test strip. -
Page 17: How To Monitor Your Blood Β-Ketone
• How to Monitor Your Blood β-Ketone Time, month, and day (if set) Getting Started If date and time are not set, dashes will show instead of numbers. Prepare your lancing device. Wash your hands using warm soapy water and dry them completely. • LOT number (CODE) for the box of blood β-Ketone test strips you are using. Remove the test strip from its foil packet. Note: For pictures that show how to open the blood β-Ketone test strip foil packet, please see the information card in the box of blood β-Ketone test strips. • KETONE and Apply Sample Insert the three black lines at the end of the test strip message, which tell you that the into the strip port. meter is ready for you to apply blood to the blood β-Ketone test strip. Push the test strip in until it stops. Obtaining A Blood Drop The meter turns on automatically. Use your lancing device to obtain a blood drop. These items show on the display window, one after the other: IMPORTANT: Blood β-Ketone test strips • have not been evaluated for alternative site Display Check – Remember to make monitoring. Use only fingertip blood sure that all items in the picture samples for blood β-Ketone monitoring. here show on the display window. - Page 18 Recommendations for Obtaining A Blood Drop Continue to touch the blood drop to the white • area at the end of the test strip until the meter Before you obtain a blood sample from the fingertip, Status bar begins the test. The meter begins the test when: make sure the sample site is clean, dry, and warm. To You hear the beeper, if the beeper is ON. warm the sample site, wash it in warm water or rub the • The display window shows the status bar. skin vigorously for a few seconds. • • Then the display window shows the Hang your arm down before pricking your fingertip to countdown. help blood flow. • Avoid squeezing the fingertip. Note: Do not remove the test strip from the • meter or disturb it during the countdown. Apply the blood sample to the test strip immediately. IMPORTANT: If the countdown Lancets and Lancing Device does not start: • Lancets are for one-time use only. Use a new lancet each What It Means: time you monitor.
-
Page 19: Understanding Your Result
Shutting Off Your Meter When: • Blood β-Ketone result remains high or becomes higher Removing the test strip from the strip port turns off than 1.5 mmol/L: the meter. You can use the opened foil packet to remove and discard What It Means: your used test strip. You may be at risk of developing diabetic ketoacidosis Discard the test strip properly. (DKA). What to Do: Note: You may also turn the Contact your healthcare professional immediately. meter off by Pressing and Holding the button. If you do "HI" Result not turn your meter off or pull the test strip out, the meter shuts off What It Means: automatically after 60 seconds. Your meter has determined that your blood β-Ketone result is higher than 8.0 mmol/L, or there may be a Understanding Your Result problem with the test strip. Blood β-Ketone is expected to be lower than 0.6 mmol/L. What to Do: Blood β-Ketone may be higher when a person is ill, is fasting, Monitor your blood β-Ketone again with exercises vigorously, or if blood glucose levels are not controlled. a new test strip. If HI shows on the display window again, contact your healthcare When: professional immediately. • Blood β-Ketone result is between 0.6 and 1.5 mmol/L and blood glucose result is 300 mg/dL (16.7 mmol/L) or higher: What It Means:... -
Page 20: Doing A Control Solution Test
CHAPTER 6 Questions? Call "E-4" Result Customer Support: Doing A Control Solution Test See page 57. What It Means: There may be a problem with the test strip. Why Do A Control Solution Test? What to Do: The control solution test tells you that your meter and test Monitor your blood β-Ketone again with a strips are working correctly. A control solution test is similar new test strip. If E-4 shows on the display to when you monitor your blood window again, contact your healthcare glucose or blood β-Ketone, except professional immediately. you use a MediSense Control Solution. You do not use a drop of blood in a control solution test. IMPORTANT: It is recommended that you repeat the When Is Doing A Control Solution blood β-Ketone test with a new test strip when: Test Recommended? •... -
Page 21: What You Will Need
• The results obtained from control testing do not reflect Insert the three black lines at the end of your personal blood glucose or blood β-Ketone levels in the test strip into the strip port. any way. • Do not swallow the control solution. • Do not inject the control solution or use the control Push the test strip in until it stops. solution as eye drops. The meter turns on automatically. What You Will Need • These items show on the display Optium Xceed meter calibrated to match the LOT window, one after the other: number of the test strip you are using • • Blood glucose or blood β-Ketone test strip and its Display Check – Remember to make instructions for use sure that all items in the picture here • MediSense Control Solutions and instructions for use show on the display window. (See Chapter 1 for more information about the How to Do Control Solution Testing Display Check.) Getting Started • Time, month, and day (if set) Wash your hands using warm soapy water and dry them completely. If date and time are not set, dashes will show instead of numbers. - Page 22 Note: Do not remove the test strip from the meter or disturb it To mark the test as a control test, Press and Release during the countdown. the button once. shows on the display window. IMPORTANT: If the countdown does not start: IMPORTANT: If you do not mark the test What It Means: as a control test, it will be saved in your You might not have applied enough control Glucose meter’s memory as one of your personal solution to the test strip. blood glucose or blood β-Ketone results. This could affect your blood glucose averages. What to Do: • Apply a second drop of control solution to the Applying Control Solution to the Test Strip test strip. Refer to your test strip instructions Turn the control solution bottle upside down three to for use for the number of seconds you have to four times to mix the solution. apply a second drop. • If the countdown still does not start, or Remove the cap. if the number of seconds you have to apply a second drop have passed, discard the test strip, turn off your meter, and try Apply a drop of control solution again with a new test strip. to the test strip in the area shown here. The control solution is drawn into the test strip.
-
Page 23: Understanding Your Result
CHAPTER 7 Questions? Call Shutting Off Your Meter Customer Support: Reviewing & Using Your Results CHAPTER 7 Removing the test strip from the strip See page 57. port turns off the meter. You can use the opened foil packet to remove and discard your used test strip. What Can Your Meter Show You? Memory Discard the test strip properly. Your Optium Xceed meter has a memory that stores up to 450 events. This is a combination of control results, your Note: You may also turn the meter personal blood glucose and blood β-Ketone results, and off by Pressing and Holding the other meter information. button. If you do not turn your meter off or pull the test strip out, You can review up to 450 of your most recent events on the meter shuts off automatically your meter’s display window. after 60 seconds. Glucose Averages Understanding Your Result You can view the average of all your blood glucose Compare the control result to the "Expected Results for results from the last 7, 14, or 30 days. If you marked your Use with MediSense Control Solutions" range printed on: control solution tests, the averages do not include control • The blood glucose test strip instructions for use, for solution results. (For more information on marking control... -
Page 24: How To See Results In Memory
How to See Results in Memory A control solution result in Memory shows with a control bottle, as long as you marked the test as a control Begin with your meter turned off. Make sure there is solution test. nothing in the strip port. Press and Release the button. • The Display Check shows on the display window. • Glucose control β-Ketone control Then your most recent result shows solution result solution result with its units on the meter’s display in Memory in Memory window, along with the time, month, and day that you got the result. (To set the correct date and To review previous results, Press and time, follow the steps in Chapter 2.) Release the button once per result. A blood glucose result in Memory will show with the letters MEM. When you reach the last result in Memory, the display window shows Blood Glucose three dashes. result in Memory A blood β-Ketone result in Memory will show with the letters KET MEM. To return to a result you previously reviewed, Press and Release the button once per result. Blood β-Ketone result in Memory ART10825-Rev-A-Man.indd 46-47... -
Page 25: How To See Averages
Results that show as LO during blood glucose monitoring are included as 20 mg/dL (1.1 mmol/L) in blood glucose averages. • Results that show as HI during blood glucose monitoring are included as 500 mg/dL (27.8 mmol/L) in blood glucose averages. Press and Hold the button to turn off your meter. Otherwise, the meter turns off after 30 seconds. While in Memory, Press and Release the button at any time to see the 7-Day average of your blood glucose results. Transferring Your Results to a Computer Note: n means how many tests were performed The results in your Optium Xceed meter's memory, along with within the 7-, 14-, or 30-Day average period. the time and date of the reading, can be transferred to a computer with the use of the Precision Link ® Direct Software Press and Release the button Version 2.5 and a Precision Link once to see the 14-Day average communications cable. For information of your blood glucose results. on how to purchase the software and cable, contact Customer Support. To install the software, please follow the instructions provided in Press and Release the button the Precision Link User's Guide. again to see the 30-Day average of your blood glucose results. -
Page 26: Understanding & Troubleshooting
CHAPTER 8 Message What It What You Questions? Call Understanding & Means Need to Do Customer Support: Troubleshooting Meter error. • See page 57. Turn the meter off, Error Messages then repeat previous monitoring steps. There are times when error messages may show on your • If the error message meter’s display window. appears again, contact Customer Support. In the next few pages, we describe the error messages that may show on your meter’s display window, what they mean, and what you need to do. - Page 27 • If the error message appears again, contact Customer Support. Test strip error. • Monitor again using a test strip designed Test strip is for use with Optium damaged, used, or Xceed. the meter does not • If the error message recognize it. appears again, contact Customer Support. ART10825-Rev-A-Man.indd 52-53...
- Page 28 CHAPTER 9 Questions? Call Your Meter’s Customer Support: Specifications See page 57. & Limitations Size Functions - Blood glucose monitoring Length: 7.47 cm - Blood β-Ketone monitoring Width: 5.33 cm (Top) - Memory 450 events 4.32 cm (Bottom) - G lucose averaging: 7-Day, 14-Day, and 30-Day Averages Thickness: 1.63 cm - C ontrol solution marking and testing Weight 42 grams - B acklight: If ON – Stays ON during Power Source One CR 2032 Lithium (coin cell) battery countdown; turns OFF 30 seconds after Battery Life Approximately 1,000 tests result is displayed. If OFF – Stays OFF...
-
Page 29: Important Information About Using Blood
CHAPTER 10 Important Information about Using Blood Questions? Call Caring For Your Meter Samples from the Forearm, Upper Arm, or Base Customer Support: of the Thumb: See page 57. • Contact your healthcare professional before you begin using any one of these alternative sites to test Cleaning Your Meter your blood glucose. Store your meter in its carrying case. • Sampling from any one of these alternative sites may If the surface of your meter gets dirty, you may clean it. cause minor bruising and may leave marks that go Use a damp cloth and mild soap. away in a short time. Healthcare professionals: Acceptable cleaning solutions • include 10% Bleach, 70% Alcohol, or 10% Ammonia. There may be times when alternative site results are different from fingertip results. This happens when IMPORTANT: blood glucose levels change rapidly (for example, Do not try to clean the strip port. after you eat a meal, after you take insulin, or during Do not pour liquid into the strip port or buttons. or after exercise). Do not place your meter in water or any other bath. • Use alternative sites to monitor your blood glucose Replacing Your Meter’s Battery before, or more than two hours after, you eat a meal,... - Page 30 How to Replace Your Meter’s Battery Gently push the battery cover in and down until you hear a click. Gently push the battery cover in and up with your thumb. Press and Hold the button to turn your meter on. If your meter Lift the battery cover out of the meter. does not turn on, review the battery installation steps and reinstall the battery. Check the date and time on your Pull on the plastic tab sticking out of meter. You may automatically be the meter to remove the old battery. prompted to reset the time and date when you first press the button to turn your meter on. (See Chapter 2, Setting Up Your System). Be sure to discard the old battery in compliance with your local Insert a new CR 2032 Lithium (coin government’s regulations. cell) battery with the plus sign (+) facing up. Place the notches on the battery cover into the appropriate molded areas. ART10825-Rev-A-Man.indd 58-59 11/10/06 1:10:59 PM...
-
Page 31: Support & Guarantee
CHAPTER 11 Support & Guarantee Questions? Call Abbott Laboratorios Uruguay SA Support Customer Support. Abbott Diabetes Care HELPLINE: 000-405-4342 Abbott Laboratories is committed to providing you Abbott Laboratorios Guatemala with support. Call us with any Abbott Diabetes Care questions you may have about HELPLINE: 597-4109 your Optium Xceed meter: Abbott Laboratorios C.A. Abbott Laboratorios Argentina SA Abbott Diabetes Care Abbott Diabetes Care HELPLINE: 0-800-372-3300 HELPLINE: 0-800-8006334 EMAIL: medisense.ar@abbott.com Abbott Laboratorios Peru Abbott Diabetes Care Abbott Laboratorios do Brasil Ltda. HELPLINE: 0-800-1-1215 Abbott Diabetes Care HELPLINE: 0800 703-0128 Abbott Laboratorios Mexico URL: www.abbottbrasil.com.br Abbott Diabetes Care HELPLINES: Mexico City (DF) 55-24-4175 Abbott Laboratorios de Chile Ltda. Outside Mexico City (DF) 01-800-711-2208 Abbott Diabetes Care HELPLINE: 800-802-226 Abbott Laboratorios de Colombia SA... -
Page 32: References
References Guarantee Abbott Laboratories (Abbott) guarantees that the Optium Xceed Meter 1. Schade DS, Eaton RP. Metabolic and clinical significance of ketosis. Special shall be free from defects in material and workmanship for a period Topics in Endocrinology and Metabolism 1982; 4:1–27. of two (2) years (24 months) from the date of purchase. Abbott’s sole 2. Wiggam MI, O’Kane MJ, Harper R, Atkinson AB, Hadden DR, Trimble ER, obligation shall be limited to replacing the defective meter with a new or Bell PM. Treatment of diabetic ketoacidosis using normalization of blood 3- reconditioned unit. The guarantee extends only to the original purchaser and is not assignable or transferable, and shall not apply to auxiliary hydroxybutyrate concentration as the endpoint of emergency management. equipment or disposable accessories. Diabetes Care 1997; 20:1347–52. Abbott guarantees that the equipment is fit for the purpose and indications described in the labeling when used in accordance with the 3. Harano Y, Kosugi K, Hyosu T, Suzuki M, Hidaka H, Kashiwagi A, Uno S, Shigeta directions for use. Unless the equipment is used in accordance with such Y. Ketone bodies as markers for Type 1 (insulin-dependent) diabetes and their instructions, this guarantee is void and of no effect. Abbott guarantees value in the monitoring of diabetes control. Diabetologia 1984; 26:343–8. the performance of the Optium Xceed Meter if it is used as directed and provided that the failure to perform or misperformance of the Optium 4. Ubukata E. Diurnal variation of blood ketone bodies in Xceed Meter has not been caused in whole or in part by the use of test insulin-dependent diabetes mellitus and non-insulin-dependent diabetes strips that are not MediSense Optium test strips manufactured by Abbott mellitus patients: The relationship to serum C-peptide immunoreactivity and Laboratories. In the unlikely even that your Optium Xceed Meter should free insulin. Ann Nutr Metab 1990; 34:333–42. - Page 33 ART10825-Rev-A-Man.indd 64 11/10/06 1:11:02 PM...
Need help?
Do you have a question about the Xceed and is the answer not in the manual?
Questions and answers