Fig. 1-1 AC Leakage Test 10. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. Samsung Electronics...
Page 3
Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards. Samsung Electronics...
4) Rotate Gear Worm Wheel ˇ counterclockwise using screw driver again up to the state of eject mode and then pick out the tape. (Refer to Fig. 2-2) ˇ GEAR WORM WHEEL SCREW DRIVER FRAME ´ GEAR WORM Œ HOLDER WORM Fig. 2-2 Fig. 2-3 Samsung Electronics...
Page 5
Reference Information 2-2 Servicing Jigs and Special Tools (Only for SV-7000W ) 2-2-1 Servicing Jig Jig Item Part No. E/Cable 68140-500-104 Use for Timer PCB (CN703, CN704) Joint PCB (CN8J01, CN8J02) This is the same as the E/CABLE-2 used for Model SV-4000W.
"B" Œ REMOVE 1 SCREW. (BH;5-4X16-BLOCK) ∏ REMOVE THE PANEL-SIDE(R) IN THE DIRECTION OF ARROW "B". ˆ REMOVE 1 SCREW. (BH;5-4X16-BLOCK) <SV-7000W> ´ LIFT UP THE CABINET-TOP IN THE DIRECTION OF ARROW . Œ REMOVE 5 SCREWS. (BH;5-4X16-BLOCK) <SV-5000W> Fig. 4-1 Cabinet Top removal...
Page 9
(BH;2-3X10-YELLOW) ˇ RELEASE 3 TABS. ˆ LIFT UP THE BOTTOM-COVER IN THE DIRECTION OF ARROW "B". "A" "B" "A" ¨ RELEASE 3 TABS. ´ REMOVE THE DECORATION-LEG IN THE DIRECTION OF ARROW "A". Fig. 4-2 Bottom Cover removal Samsung Electronics...
Page 10
Disassembly and Reassembly 4-1-3 Ass’y Front Panel removal Œ RELEASE 4 HOOKS. (Top view) ´ RELEASE 3 HOOKS. (Bottom view) Fig. 4-3 Ass’y Front Panel removal Samsung Electronics...
Page 11
´ REMOVE THE ASS'Y FUNCTION IN THE DIRECTION OF ARROW "A". Fig. 4-4 Ass’y Timer removal 4-1-5 Ass’y Digital removal Œ REMOVE HOLDER PCB. ´ LIFT UP THE ASS'Y DIGITAL IN THE DIRECTION OF ARROW. Fig. 4-5 Ass’y Digital removal Samsung Electronics...
Page 12
ˇ REMOVE 3 SCREWS. Œ REMOVE 2 SCREWS. ¨ LIFT THE ASS'Y FULL DECK UP. ´ REMOVE BRACKET-FRAME. ˆ REMOVE 1 SCREW. ∏ LIFT THE ASS'Y MAIN PCB UP TO REMOVE. Ø RELEASE 2 TABS. Fig. 4-6 Chassis Unit removal Samsung Electronics...
3) When replacing the cylinder ass’y, be sure to adjust the “X-Point” and “Head switching adjustment”. 4) Among Samsung VCR remote control used for adjustment as a accessory, only the remote control that has figures buttons (0 ~ 9) is available for all adjustment regardless of chassis.
Page 29
Alignment and Adjustment 6-1-2 Test point location for adjustment mode setting SV-7000W (TIMER PCB ; Top View) SV-5000W (F/TIMER PCB ; Top View) Fig. 6-2 Samsung Electronics...
1) Playback the alignment tape (Color bar). maximum. 2) Press the ÒTESTÓ (SV-7000W ; SW711, SV-5000W ; 6) Turn the Power off. SW718) button on Timer PCB to set the adjustment mode.
6-3 Head Switching Point Adjustment 1) Playback the alignment tape. 2) Press the ÒTESTÓ (SV-7000W ; SW711, SV-5000W ; SW718) button on Timer PCB to set the adjustment mode. (See Fig. 6-2) 3) Press the ÒREC.SPEEDÓ button of remote control then adjustment is operated automatically. (See Fig. 6-1) 4) Turn the Power off.
2) In case Micom (IC601) and NVRAM (IC605 ; EEPROM) is replaced, be sure to set the corresponding option number of the repaired model. (If the option is not set, the unit is not operated.) 1) Press the ÒTESTÓ (SV-7000W ; SW711, SV-5000W ; SW718) button on Timer PCB to set the adjustment mode. (See Fig. 6-2) 2) Press the ÒMENUÓ...
Page 34
Exploded View and Parts List 7-1 Cabinet Assembly Samsung Electronics...
Page 35
Refer to table below ASSY-PANEL FRONT Refer to table below DOOR-CASSETTE AC61-62003A SPRING;-,SUS304,(GE/RCA),-,-,-,- AC64-00094A DECORATION-RING;-,ABS94HB,-,-,BLK,-,SV-3 Refer to table below CABINET-TOP-ASSY AC97-00484A ASSY-PANEL SIDE L SV-7000W ONLY AC97-00485A ASSY-PANEL SIDE R SV-7000W ONLY Refer to table below LEG-DECORATION AC61-20237A HOLDER;ABS94HB,T2,BLK,23.1*18.5,-,- AC61-00029A CONNECTOR-BOARD;-,HIPS94HB,-,T2,59,-,BLK AC61-00028A CONNECTOR-BOARD;-,HIPS94HB,-,T2,128.5,-, AC64-11009A KNOB-SLIDE;-,ABS,HB,BLK,-,SV-300W...
Page 36
Exploded View and Parts List 7-2 Mechanical Parts (Top Side) Samsung Electronics...
Important safety notices : Components identified with the mark have the special characteristics for safety. When replacing any of these components. Use only the same type. 3 Block Identification of Main PCB 12-2 Samsung Electronics...
Page 80
¨ Ø ∏ Fig. 1-1 Top parts Location-1 Œ BRACKET FL TOP ´ GEAR FL CAM ˇ MOTOR LOADING ASS’Y ¨ LEVER FL ARM ASS’Y ˆ HOLDER FL CASSETTE ASS’Y Ø LEVER FL DOOR ∏ SLIDER FL DRIVE Samsung Electronics...
Page 81
Ò GEAR IDLE ¨ PLATE CYLINDER B Ú LEVER IDLE ˆ PLATE CYLINDER A Æ LEVER T BRAKE ASS’Y Ø ACE HEAD ASS’Y ı DISK T REEL ∏ UNIT PINCH ASS’Y ” LEVER #9 GUIDE ASS’Y ’ LEVER TENSION ASS’Y Samsung Electronics...
Page 82
´ GEAR JOINT 2 ˇ BRAKET GEAR ¨ MOTOR CAPSTAN ASS’Y ˆ LEVER T LOAD ASS’Y Ø GEAR LOADING DRIVE ∏ LEVER S LOAD ASS’Y ” HOLDER CLUTCH ASS’Y ’ BELT PULLEY ˝ SLIDER CAM Ô SLEEVE TENSION Samsung Electronics...
Page 83
Note : Take care not to change assembly direction. in the direction of arrow ÒBÓ. Œ 2 SCREWS Œ LEVER FL DOOR ´ BRACKET FL TOP "A" "B" ´ HOOK Fig. 1-5 Lever FL Door Removal Fig. 1-4 Bracket FL Top Removal Samsung Electronics...
Page 84
´ BOSS ˇ SLIDER FL DRIVE "B" BOSS [B] Fig. 1-7 Lever FL Arm Ass’y Removal RAIL [C] Œ HOLDER FL RAIL [D] CASSETTE ASS'Y ´ LEVER FL CASSETTE-R "A" BOSS [A] Fig. 1-6 Holder FL Cassette Ass’y Removal Samsung Electronics...
Page 87
Œ GEAR LOADING DRIVE HOOK [A] ´ SLIDER CAM ˇ LEVER T LOAD ASS'Y ¨ LEVER S LOAD ASS'Y Œ SCREW Fig. 1-12 Motor Loading Ass’y Removal Fig. 1-13 Gear Loading Drive, Slider Cam, Lever T, S Load Ass’y Removal Samsung Electronics...
Page 88
PIN A PIN C PIN D PIN B ˇ SLIDER CAM Fig. 1-14 Assembly of Gear Loading Drive, ´ SLEEVE TENSION Slider Cam, Lever T, S Load Ass’y Fig. 1-15 Lever Tension Ass’y, Band Brake Ass’y, Sleeve Tension Removal Samsung Electronics...
Page 89
ˇ SPRING BRAKE ´ GEAR IDLE "B" HOOK [C] ´ GEAR IDLE ´ LEVER T BRAKE ASS'Y Œ LEVER S BRAKE ASS'Y HOOK [B] Fig. 1-17 Lever Idle Ass’y Removal Fig. 1-16 Lever S, T Brake Ass’y Removal 1-10 Samsung Electronics...
Page 90
1) Remove the Washer Slit Œ. 2) Lift the Holder Clutch AssÕy ´. Œ DISK S REEL Œ WASHER SLIT ´ DISK T REEL ´ HOLDER CLUTCH ASS'Y Fig. 1-18 Disk S, T Reel Removal Fig. 1-19 Holder Clutch Ass’y Removal Samsung Electronics 1-11...
Page 91
Œ LEVER UP DOWN ASS'Y ¨ RING ˇ GEAR ∏ HOOK 35˚ Ø POST MAIN BASE Fig. 1-21 Assembly of Lever Up Down Ass’y, Gear Center Ass’y Fig. 1-20 Lever Up Down Ass’y, Gear Center Ass’y Removal 1-12 Samsung Electronics...
Page 92
2) When reinstalling, be sure to apply grease on the post pinch roller. HOOK [A] ´ PLATE JOINT Œ UNIT PINCH ASS'Y ˇ SPRING PINCH DRIVE Fig. 1-22 Guide Cassette Door Removal Fig. 1-23 Unit Pinch Ass’y, Plate Joint, Spring Pinch Drive Removal Samsung Electronics 1-13...
Page 93
2) After reinstalling, check the bottom side of the Post #9 Guide to stick to the top side of Main Base. ´ LEVER #9 GUIDE ASS'Y Œ SPRING #9 GUIDE Fig. 1-25 FE Head Removal Fig. 1-24 Lever #9 Guide Ass’y Removal 1-14 Samsung Electronics...
Page 94
2) Remove the screw Œ. 3) Lift the ACE Head AssÕy ´. Œ SLIDER S ASS'Y Œ SCREW ´ SLIDER T ASS'Y ´ ACE HEAD ASS'Y Fig. 1-27 Slider S, T Ass’y Removal Fig. 1-26 ACE Head Removal Samsung Electronics 1-15...
Page 95
1-2-27 Lever Head Cleaner Ass’y Removal (Optional) 1) Release the Hook Œ. 2) Lift the Lever Head Cleaner AssÕy ´. ´ LEVER HEAD CLEANER ASS'Y Œ HOOK Fig. 1-28 Cylinder Ass’y Removal Fig. 1-30 Lever Head Cleaner Ass’y Removal 1-16 Samsung Electronics...
Page 96
4) Rotate Gear Worm Wheel ˇ counterclockwise using screw driver again up to the state of eject mode and then pick out the tape. (Refer to Fig. 1-32) ´ MOTOR CAPSTAN ASS'Y Fig. 1-31 Motor Capstan Ass’y Removal FRAME Fig. 1-33 Samsung Electronics 1-17...
Page 97
CAPSTAN MOTOR PULLEY BELT PULLEY ∆ HOLDER CLUTCH ASS’Y GEAR CENTER ASS’Y GEAR IDLE (2Point) LOADING MOTOR BAND BRAKE ASS’Y BRAKE T ASS’Y Æ : Cleaning O : Check and replacement in necessary 3 : Add Oil 1-18 Samsung Electronics...
Page 98
Fig. 2-1 Location of Tape Transport Adjustment FE HEAD CYLINDER ASS'Y PINCH ROLLER GUIDE ROLLER "S" GUIDE ROLLER "T" POST TENSION #8 GUIDE POST #9 GUIDE POST MAIN BASE ACE HEAD CAPSTAN SHAFT #3 GUIDE POST Fig. 2-2 Tape Travel Diagram Samsung Electronics...
Page 99
1) See page 5-1 of the Service Manual for ACE Head position (X-Point) adjustment. Fig. 2-3 Location of ACE Head Adjustment Screw AUDIO HEAD VIDEO HEAD 0 ~ 0 .25 mm CONTROL HEAD Fig. 2-4 ACE Head Height Adjustment Samsung Electronics...
Page 100
) driver to obtain a flat video RF envelope as shown in Fig. 2-8. IDEAL ENVELOPE S HEIGHT S HEIGHT T HEIGHT T HEIGHT TOO HIGH TOO LOW TOO HIGH TOO LOW GUIDE ROLLER T GUIDE ROLLER S Fig. 2-8 Guide Roller S, T Height Adjustment Samsung Electronics...
Page 101
145 ± 30 Cassette Torquemeter 4) Transportation of accurate driving force is done by gears. (Gear Center AssÕy) Note : If the spec. does not meet the followings speci- fications, replace the holder clutch assÕy and then recheck. Samsung Electronics...
Page 102
Fig. 2-13 Tension Pole and Back Tension Adjustment Note : 1) Mark on Main Base is located in about 1.3mm from inside of bending line. 2) Be careful not to deform the region of adjusting on Main Base up and down at adjusting. Samsung Electronics...
Page 103
Alignment and Adjustment MEMO Samsung Electronics...