— — Drain — Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”. N.B. This machine is controlled by sensors. Please avoid excessive detergent dosing. Whirlpool is a registered trademark of Whirlpool USA 5019 312 10172...
Page 3
If the spin speed “0” is selected, the final spin is cancelled, but not the intermediate spins. The programme ends with a drain cycle. Whirlpool is a registered trademark of Whirlpool USA 5019 312 10172...
CONTENTS BEFORE USING THE WASHING MACHINE FIRST WASH CYCLE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES CLEANING THE FOREIGN BODY TRAP DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER-SALES SERVICE TRANSPORT AND HANDLING INSTALLATION ELECTRICAL CONNECTION...
BEFORE USING THE WASHING MACHINE 1.Remove the packaging and check 6.Electrical connection • Electrical connections must be carried out by a a. Cut and remove the shrink-wrap. qualified technician in compliance with the b. Remove the top protection and the protective corners.
FIRST WASH CYCLE We recommend that the first wash cycle be carried out empty. This will remove any residual water used in the factory checks. 1.Turn on the tap. 2.Close the drum flaps. 3.Pour a small amount of detergent (about 30 ml) into the detergent dispenser 4.Select a short programme and low spin speed (see programme chart).
DESCRIPTION OF THE WASHING MACHINE 1.Lid 2.Detergent dispenser 3.Drum flaps • To open the drum press the small flap and hold the large flap. 4.Pump and foreign body trap 5.After-Sales Service sticker (behind the foreign body trap cover) 6.Mobility lever (depending on model) •...
Page 9
Stain removal Dyeing and bleaching • Blood, milk, egg and other organic substances Products usually consist of dye colour, fixing agent are generally removed by the enzyme phase of and salt. Pour the dye colour, the fixing agent and the programme. then the salt directly into the empty drum.
DETERGENTS AND ADDITIVES Choice of the right detergents and additives Dosage Follow the instructions on the detergent pack in The type of detergent depends on: relation to: • type of fabric (cottons, easy care/synthetics, • the degree and type of soiling; delicate items, wool).
CLEANING THE FOREIGN BODY TRAP The appliance is provided with a self-cleaning pump. The foreign body trap keeps objects like buttons, coins, safety-pins etc. which have been left in the laundry. 1. Unplug the appliance. 2. Open the foreign body trap cover with a coin. 3.
DRAINING RESIDUAL WATER When should I drain residual water (draining problem)? • Before transporting (moving) the machine. • If the appliance is installed in a room subject to sub-zero temperatures. It is best in this case to drain the machine after every wash.
Page 13
Water inlet hose filter Check and clean regularly (at least two or three times a year). 1.Unplug the appliance. 2.Turn off the tap. 3.Unscrew the hose from the tap. 4.Carefully clean the filter located at the end of hose, without assembling it, for example with a tooth-brush.
Appliance exterior and control panel Lid seal • Clean from time to time with a damp cloth. • Clean using normal household cleaner (do not Water inlet hose(s) use abrasive products or paint-thinners). • Check the hose regularly for brittleness and •...
AFTER-SALES SERVICE Before contacting After-Sales Service: Specify: • The nature of the problem. 1.Try to remedy the problem yourself (see • The exact model of the appliance. “Troubleshooting Guide”). • The service code (number after the word 2.Restart the programme to check whether the SERVICE).
INSTALLATION Removal of transport bracket The appliance is fitted with a transport bracket to avoid any possible damage during transport. Before using the appliance, the transport bracket at the back MUST be removed. 1.Unscrew the two screws A and the four screws B with a flat screwdriver or a No.
Page 17
Adjust the feet Install the appliance on a level surface, near to electrical, water and drain connections. If the floor is uneven, adjust the feet (do not insert pieces of wood, cardboard etc. under the feet): 1.Loosen the locknut using the wrench provided. 2.Adjust the height of the foot by hand.
Page 18
Water stop anti-flooding system (depending on model) • Screw the hose to the water supply tap. Turn the tap fully on and check the water-tightness of the connection. • The appliance must not be connected to the mixing tap of a non-pressurized water heater! •...
ELECTRICAL CONNECTION Do not use extension leads or multi sockets. Electrical connections must be made in accordance with local regulations. 1) Warning - this appliance must be earthed This appliance is normally supplied with a mains lead having a plug fitted in the factory which has been checked for correct earth continuity.