Eeprom Address Map - Epson LX-300+II RTP Service Manual

EPSON LX-300+II/300+II RTP/1170II
A.2 EEPROM Address Map
This section provides the EEPROM address map.
NOTE: The data of two or more bytes are assigned as lower byte to lower
address and higher byte to higher address.
*1: The data are fixed by each printer hardware in the factory. The data
should not be changed afterwards.
NOTE: The data is fixed by each printer hardware in the factory. The data shold
not be changed afterwards.
Table A-13. EEPROM Address Map
Address Explanation
Area 0
00H-03H Reserved
Driving Line count for 0-0FFFFFFFFH(count)
04H-07H
ribbon change timing See Remote spec TLcmd
0-0FFFFFFFFH(minute)
08H-0BH Driving Hour
See Remote spec TLcmd
0-0FFFFFFFFH(count)
0CH-0FH Driving Line count
See Remote spec TLcmd
0-99(the last two figures of Anno Domini)
10H Starting Year
See Remote spec SDcmd
1-12
11H Starting Month
See Remote spec SDcmd
1-31
12H Starting Data
See Remote spec SDcmd
b0: In Tear Off state
13H Backup Flags
b1 to b7: Reserved
14H-17H Reserved
Area1
1 to 22x432 by 0.0588 mm (1/432 inch),
18H,19H Page length for tractor
0000H : 279.4 mm (11 inches: same as default)
1 to 22x432 by 0.0588 mm (1/432 inch),
1AH,1BH Page length for CSF
0000H : 558.8 mm (22 inches: same as default)
Page length for rear 1 to 22x432 by 0.0588 mm (1/432 inch),
1CH,1DH
manual insertion 0000H : 558.8 mm (22 inches: same as default)
TOF adjustment value -144 to 432 (0.0 mm to 8.5 mm +25.4 mm
1EH,1FH
for tractor (1 inch), by 0.0588 mm (1/432 inch))
Appendix
QPIT Factory
Setting
Settings Settings
00H 00H
00000000H 00000000H
00000000H 00000000H
00000000H 00000000H
00H 00H
00H 00H
00H 00H
0: No 1: Yes
00H 00H
0000H 0000H
0000H 0000H
0000H 0000H
0000H 0000H
0000H 0000H
(8.5 mm) (8.5 mm)

EEPROM Address Map

Table A-13. EEPROM Address Map (continued)
Address Explanation
TOF adjustment value -144 to 432 (0.0 mm to 8.5 mm +25.4 mm
20H,21H
for CSF (1 inch), by 0.0588 mm (1/432 inch))
TOF adjustment value -144 to 432 (0.0 mm to 8.5 mm +25.4 mm
22H,23H
for rear manual insertion (1 inch), by 0.0588 mm (1/432 inch))
Bottom margin for 1 to 22x432 by 0.0588 mm (1/432 inch), 0000H :
24H,25H
tractor 279.4 mm (11inches: same as default)
-144 to -72, 0 : -72(4.2 mm)
26H,27H TOF Minimum value In case that it is big than -72, a value considers as
-72
0: Draft
28H Font selection 1: Roman
2: Sans serif
0: 10 cpi
29H Pitch selection 1: 12 cpi
2: 15 cpi
2AH Reserved
2BH,2CH Reserved
0:Bi-d.
2DH Print direction setting
1:Uni-d.
Revision D
QPIT Factory
Setting
Settings Settings
0000H 0000H
(8.5 mm) (8.5 mm)
0000H 0000H
(8.5 mm) (8.5 mm)
0000H 0000H
0000H 0000H
00H 00H
(Draft) (Draft)
3: 17 cpi
00H 00H
4: 20 cpi
(10 cpi) (10 cpi)
5: Proportional
00H 00H
0000H 0000H
00H 00H
(Bi-d.) (Bi-d.)
114