All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by EL 0765 BG CD Customer Service...
EN 2 Q528.1E LA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.3 Multimedia 1.1 Technical Specifications 1.2 Connections Supported file formats : JPEG 1.3 Chassis Overview : MPEG1, MPEG2 : MP3 Notes: : Slideshow (.alb)
Page 3
Technical Specifications, Connections, and Chassis Overview Q528.1E LA EN 3 Connections H_16800_105.eps 090507 Figure 1-1 Connection overview Note: The following connector colour abbreviations are used Digital Audio Out: Cinch: S/PDIF - Out (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Bk - Coaxial 0.4 - 0.6V...
Page 4
EN 4 Q528.1E LA Technical Specifications, Connections, and Chassis Overview EXT3: Cinch: Video YPbPr - In - Audio L 0.5 V / 1 kohm Gn - Video Y / 75 ohm - Ground Audio Bu - Video Pb 0.7 V...
Be careful during measurements in the high voltage by the workshop during a repair: section. • Use only lead-free soldering tin Philips SAC305 with order • Never replace modules or other components while the unit code 0622 149 00106. If lead-free solder paste is required, is switched "on".
Page 6
EN 6 Q528.1E LA Safety Instructions, Warnings, and Notes avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin. 2.3.5 Alternative BOM identification The third digit in the serial number (example: AG2B0335000001) indicates the number of the alternative B.O.M.
Directions for Use Q528.1E LA EN 7 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
EN 8 Q528.1E LA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: • Figures below can deviate slightly from the actual situation, 4.1 Cable Dressing due to the different set executions. 4.2 Service Positions • Follow the disassemble instructions in described order.
Page 9
Mechanical Instructions Q528.1E LA EN 9 H_16800_107.eps 090507 Figure 4-2 Cable dressing 47” sets Service Positions The foam bars (order code 3122 785 90580 for two pieces) can be used for all types and sizes of Flat TVs. See figure “Foam bars”...
Page 10
EN 10 Q528.1E LA Mechanical Instructions Important: For (older) FTV sets without these "mushrooms", it is obligatory to use the provided screws, otherwise it is possible to damage the monitor inside! Assy/Panel Removal 4.3.1 Rear Cover Warning: Disconnect the mains power cord before you remove the rear cover.
Page 11
Mechanical Instructions Q528.1E LA EN 11 4.3.2 Side I/O Board Refer to next figures for details. 1. Slide the unit upwards. 2. Unplug connector [1] and take the PWB out of its casing. When defective, replace the whole unit. H_16800_110.eps...
Page 12
EN 12 Q528.1E LA Mechanical Instructions 4.3.3 USB I/O Board 4.3.4 Keyboard Control Board Refer to next figures for details. Refer to next figures for details. 1. Remove screw [1]. 1. Remove the screws [1] and turn the board upside-down.
Page 13
Mechanical Instructions Q528.1E LA EN 13 4.3.5 IR & LED Board 4.3.7 Display Supply Panel - 47” sets Refer to next figure for details. Refer to next figure for details. 1. Release clip [1], lift the board and take it out.
Page 14
EN 14 Q528.1E LA Mechanical Instructions 4.3.8 Small Signal Board (SSB) 4.3.9 AmbiLight Unit Caution: it is mandatory to remount all different screws at their The AmbiLight Units are located in the back cover. Refer to original position during re-assembly. Failure to do so may result next figure for details.
Page 15
Mechanical Instructions Q528.1E LA EN 15 H_16800_121.eps 110507 Figure 4-22 LCD Panel H_16770_097.eps 220307 Figure 4-23 Central Sub-frame...
Page 16
EN 16 Q528.1E LA Mechanical Instructions Set Re-assembly To re-assemble the whole set, execute all processes in reverse order. Notes: • While re-assembling, make sure that all cables are placed and connected in their original position. See figure "Cable dressing".
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 17 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: – Picture mute (blue mute or black mute). 5.1 Test Points – Automatic volume levelling (AVL). 5.2 Service Modes –...
Page 18
EN 18 Q528.1E LA Service Modes, Error Codes, and Fault Finding How to Activate SAM the TV will go to the Stand-by mode. If the NVM was corrupted Via a standard RC transmitter: key in the code “062596” or empty before this action, it will be initialized first (loaded with directly followed by the “INFO”...
Page 19
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 19 5.2.3 Customer Service Mode (CSM) - the serial number of the SSB, which consists of six digits. Both can be found on a sticker on the PWB of the SSB itself.
Page 20
EN 20 Q528.1E LA Service Modes, Error Codes, and Fault Finding the customer wants to make use of the HDMI functionality, the SSB has to be replaced. • Tuner frequency. Indicates the frequency the transmitter is tuned to. • TV System. Gives information about the video system of the selected transmitter.
Page 21
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 21 Stepwise Start-up due to overvoltage. It is recommended to measure first the FET 7U01 on short-circuit before activating SDM via the service pads. There are two possible situations: one for protections detected...
Page 22
EN 22 Q528.1E LA Service Modes, Error Codes, and Fault Finding Off/Stby to Semi Stand by or Protection Mains is applied Standby Supply starts running. All standby supply voltages become available . action holder: MIPS action holder: St-by st-by µP resets...
Page 23
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 23 The supply fault line is an OR SUPPLY-FAULT I/O line Supply fault error function of DCDC, DCDC5050 is High? and POD/CI supply switch. Enable the supply fault detection algorithm Set I²C slave address...
Page 24
EN 24 Q528.1E LA Service Modes, Error Codes, and Fault Finding switch off the remaining DC/DC Log power-ok error and enter Power-ok display high ? converters protection Switch POD-MODE and ON-MODE 3-th try? I/O line high. Reset the Pacific by pulling LOW the Pacific hardware reset line during 100ms.
Page 25
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 25 action holder: AVC action holder: St-by autonomous action Semi Standby Wait until previous on-state is left more than 2 seconds ago. (to prevent LCD display problems) Assert RGB video blanking...
Page 26
EN 26 Q528.1E LA Service Modes, Error Codes, and Fault Finding action holder: AVC action holder: St-by autonomous action Semi Standby Wait until previous on-state is left more than 2 seconds ago. (to prevent LCD display problems) Assert RGB video blanking...
Page 27
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 27 action holder: AVC Active action holder: St-by autonomous action Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext audio outputs to ground...
Page 28
EN 28 Q528.1E LA Service Modes, Error Codes, and Fault Finding action holder: MIPS Active action holder: St-by autonomous action Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext audio outputs to ground...
Page 29
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 29 Semi Stand by action holder: MIPS action holder: St-by autonomous action If ambientlight functionality was used in semi -standby (lampadaire mode), switch off ambient light *) If this is not performed and the set is...
Page 30
EN 30 Q528.1E LA Service Modes, Error Codes, and Fault Finding action holder: MIPS action holder: St-by autonomous action Log the appropriate error and set stand-by flag in NVM Redefine wake up reasons for protection state and transfer to stand-by µP.
Introduction whether the Small Signal Board (SSB) or the display of a Flat ComPair (Computer Aided Repair) is a Service tool for Philips TV is defective. Thus to determine if LVDS, RGB, and sync Consumer Electronics products. and offers the following: signals are okay.
Page 32
EN 32 Q528.1E LA Service Modes, Error Codes, and Fault Finding right, new errors are logged at the left side, and all other errors Take notice that some errors need more than 90 seconds shift one position to the right.
Page 33
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 33 Table 5-3 Error code overview Error Description Error/Prot Detected by Device Result MIPS PNX8535 Error logged PNX8535 does not boot (HW cause) E Stby P PNX8535 Error blinking 5V, 12V supply...
Page 34
EN 34 Q528.1E LA Service Modes, Error Codes, and Fault Finding visible via the front LED. This is especially useful for fault 5.7.2 Hardware Protections finding, when there is no picture. The only real hardware protection in this chassis is (in case of When the blinking LED procedure is activated in the “on”...
Page 35
Service Modes, Error Codes, and Fault Finding Q528.1E LA EN 35 the ENABLE-1V2 becomes active (low) and +12V is • Symptom: +1V2, +1V4, +1V8, +2V5 or +3V3 shows a high present. The +Vtun generator (present only for the level of ripple voltage (audible noise can come from the analogue version of China platforms) will generate +33V filtering coils 5U01, 5U02 or 5U60).
EN 36 Q528.1E LA Service Modes, Error Codes, and Fault Finding 5.8.10 Display option code Caution: In case you have replaced the SSB, always check the display option code in SAM, even if you have picture. With a wrong display option code it is possible that you have picture, but that in certain conditions you have unwanted side-effects.
Page 37
6. Press “Shift U” on your PC keyboard. You should now see 1. Disconnect the TV from the Mains/AC Power. the following info: 2. Press the "OK" button on a Philips DVD RC-6 remote – PNX2015 Loader V1.0 control (it is also possible to use the TV remote in "DVD"...
Page 38
EN 38 Q528.1E LA Service Modes, Error Codes, and Fault Finding • 1.4 Display_DISPT_x.x.x.x.zip. Not to be used by Service technicians. • 1.5 EDID_Q581X_x.x.x.x.zip. Contains the EDID content of the different EDID NVM’s. See ComPair for further instructions. For sets with three HDMI connectors.
Block Diagrams, Test Point Overview, and Waveforms Q528.1E LA Block Diagram Video VIDEO B03B B04Q MAIN TUNER PNX8535 PNX8535: FLASH 7H00 PNX8537E/M2A 7T57 B04K ANALOGUE AV TDA9898HL 1T04 1T55 7HA0 IF-FILTN1 TD1716F/IHXP IF1-B 7T55 PNX8535 NAND512W3A2BN6E CVBS4 IF-FILTP1 CVBS IF1-A...
Page 73
Circuit Diagrams and PWB Layouts Q528.1E LA PNX 8535: Digital Video In Personal Notes: 3HK0 C2 PNX 8535: DIGITAL VIDEO IN 7H00-3 B2 B04H B04H 9HK0 C2 IHSM C2 7H00-3 PNX8535 HDMI RX2- RX_0 RX2+ HOT-PLUG HOT_PLUG RX1- RX_1 RX1+...
Circuit Diagrams and PWB Layouts Q528.1E LA SSB: SRP List Explanation Example Personal Notes: 1.1. Introduction Net Name Diagram +12-15V AP1 (4x) +12-15V AP4 (4x) SRP (Service Reference Protocol) is a software tool that creates a list with all references to signal lines. The list contains...
Circuit Diagrams and PWB Layouts Q528.1E LA IR & LED Panel Layout IR & LED Panel (Top Side) 1040 -- 3042 -- 3053 -- 3071 -- 3077 -- 3999 -- 7051 -- 7071 -- 3040 -- 3043 -- 3061 --...
Page 118
Circuit Diagrams and PWB Layouts Q528.1E LA Personal Notes: E_06532_013.eps 131004...
Page 119
Alignments Q528.1E LA EN 119 8. Alignments Index of this chapter: • Press MENU on the RC to switch back to the main menu. 8.1 General Alignment Conditions • Switch the set to stand-by mode. 8.2 Hardware Alignments 8.3 Software Alignments For the next alignments, supply the following test signals via a 8.4 Option Settings...
EN 120 Q528.1E LA Alignments Table 8-2 Tint settings which ICs to address. The presence / absence of these specific ICs (or functions) is made known by the option codes. Colour Temp. Notes: Cool • After changing the option(s), save them by pressing the OK...
Page 121
Alignments Q528.1E LA EN 121 8.4.4 Opt. No. (Option numbers) Select this sub menu to set all options at once (expressed in Table 8-5 Option code overview two long strings of numbers). An option number (or "option byte") represents a number of Displ.
EN 122 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: Remaining additional key components in this chassis are: 9.1 Introduction • PNX5050. 9.2 Display Supply •...
Page 123
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 123 Sets with all resolutions @ 50 Hz use the PNX8535 SoC, the Frame Insertion (DFI). This DFI panel also contains an extra PNX5050 Video Back-end Processor and the T6TF4HFG EPLD to drive the AmbiLight units.
Page 124
EN 124 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Display Supply For a block diagram see figure ”Block diagram Display Supply 32 and 37”. 9.2.1 32 and 37” Sets The 32 and 37” sets in this chassis come with a serviceable Display Supply Unit.
Page 125
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 125 The output voltages of +12 V, +15 V, and +24 V (or +295 V in 7B05 (via resistors 3B60 and 3B34). When the voltage on pin case of scanning backlight) are generated through a so-called 1 of the MOSFET reaches the threshold level, the MOSFET resonant DC-DC power converter (LLC-converter) (item no.
Page 126
EN 126 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3.7 Service Tips After replacing some components in the primary circuit of the Platform Supply, a variable transformer has to be used to ramp up the mains voltage from 0 to 30 V. This will result in the Platform Supply to start-up.
Page 127
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 127 On-board DC/DC Converters Block diagram In this platform, on-board DC/DC converters have been Vout foreseen. See also diagrams B02A, B02B and B02C. 9.4.1 PSU Start-up Sequence PWM GENERATOR 1.
Page 128
EN 128 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Service Tips • C address 0x10. • When a power MOS-FET is found defective, replace the • Decoding from low-IF to MPEG transport stream. other power MOS-FET as well.
Page 129
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 129 Figure 9-7 PAL/SECAM video broadcast reception block diagram...
Page 130
EN 130 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Figure 9-8 PAL/SECAM audio broadcast reception block diagram...
Page 131
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 131 9.5.3 Digital signal processing (front-end) Refer to figure “DVB-T signal broadcast reception block diagram” for details of digital signal processing. Figure 9-9 DVB-T signal broadcast reception block diagram...
Page 132
EN 132 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets PNX8535 9.6.1 Video Subsystem Refer to figure “Video flow diagram” for a clarification of the In this chassis, the PNX8535 is responsible for the audio/video blocks that are used in this device.
Page 133
Audio DSP into the system memory for “lip- sync” delay. The Sony/Philips Digital Interface (SPDIF) input is used to get compressed data into the system memory. The multiplexer in The Audio Output (AO) block supports output of up to four front of the block allows two possible sources of SPDIF signals.
Page 134
EN 134 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Demodulation & Decoding DSP is used for demodulation and The sub-system consists of the following modules: decoding of all analogue terrestrial TV sound standards that the TV520 platform covers.
Page 135
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 135 The Conditional Access Interface supports direct control and 9.7.1 HD sets @ 50 / 100 Hz communication to the PC-Card attached to a PCMCIA interface. The interface supports the DVB CI-CA and In HD sets (50 / 100 Hz), the output signal coming from the CableCard specification.
Page 136
EN 136 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.7.2 Full-HD sets @ 50 / 100 Hz selection between analogue and pulse-width modulation, depending on which display is used. Scanning Backlight displays require an analogue signal, and all other displays a In full-HD sets @ 50 / 100 Hz, the output signal coming from the pulse-width modulated.
Page 137
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 137 9.7.3 PNX8535 For sets where the PNX8535 outputs LVDS to the PACIFIC 3, refer to figure “PNX8535 LVDS interface to PACIFIC 3” for details. H_16770_131.eps 270307 Figure 9-15 PNX8535 LVDS interface to PACIFIC 3 (diagram B04O) For sets where the PNX8535 outputs CMOS to the PNX5050 or CYCLONE II (EP2C8F256C7N), refer to figure “PNX8535...
Page 138
EN 138 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets H_16770_132.eps 270307 Figure 9-16 PNX8535 CMOS interface to PNX5050 or CYCLONE II (diagram B04O)
Page 139
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 139 9.7.4 PNX5050 • Video input (CMOS). • Graphics input (PCI). • Video & Graphics (CMOS). The PNX5050 performs the following tasks: • • Picture quality improvement (Natural Motion, etc.).
Page 140
EN 140 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.7.5 PACIFIC 3 (T6TF4HFG) • Video input: – US sets: single LVDS from PNX8535, dual LVDS from CYCLONE II The PACIFIC 3 performs the following tasks: – CMOS from PNX5050 •...
Page 141
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 141 RESET from PNX8535 Resonator 60MHz Vsync to Scanning Back Light D isplay From PNX5050 To dimming circuit CMOS input :Vsync Configuration LCD-Power -ON Flash memory I2C SSB H_16770_138.eps...
EN 142 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Ambient Light One LED package +12V In this chassis, LED AmbiLight units are introduced as the successor of CCFL AmbiLight units. The system that is used is called “LUMILED”.
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 143 Abbreviation List Dynamic Frame Insertion Directions For Use: owner's manual Digital Media Reader: card reader 0/6/12 SCART switch control signal on A/V Digital Natural Motion board. 0 = loop through (AUX to TV), 6...
Page 144
Sync On Green non-linear resistor SOPS Self Oscillating Power Supply NTSC National Television Standard S/PDIF Sony Philips Digital InterFace Committee. Colour system mainly SRAM Static RAM used in North America and Japan. Small Signal Board Colour carrier NTSC M/N= 3.579545...
Page 145
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 145 640x480 (4:3) Variable Level out: processed audio output toward external amplifier Vestigial Side Band; modulation method WYSIWYR What You See Is What You Record: record selection that follows main...
EN 146 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10 IC Data Sheets This section shows the internal block diagrams and pin configurations of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic"...
EN 148 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.4 Diagram B03A, TDA10048HN (IC7T17-1) Block Diagram AGC_TUN AGC_IF ANALOG ΣΛ STEP INTERFACE DIGITAL FRONT-END DUAL CHANNEL ESTIMATION AND OFDM AND CORRECTION DEMODULATION ΣΛ STEP INTERFACE DIGITAL DYNAMIC...
Page 149
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 149 9.10.5 Diagram B03B, TDA9898HL (IC 7T57) Block Diagram 4 MHz reference input EXTERNAL SOUND BAND-PASS FILTER i.c. ADRSEL GNDD LFSYN2 GNDA EXTFILO EXTFILI FREF OPTXTAL 43, 44 40, 41...
Page 150
EN 150 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.6 Diagram B04, PNX8535 (IC 7H00) Block Diagram DDR-II DDR-II 32 MB 32 MB PNX8535 Matrix Display 1368 × 768 A/V INPUTS MIPS32@240MHz TV control, Pixel OSD Source select...
Page 151
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 151 9.10.7 Diagram B05, PNX5050 (IC 7C00) Block Diagram DDR SDRAM PNX5050 MAIN MEMORY INTERFACE SD video ITU-R BT.656 PICTURE 4 : 2 : 2 VIDEO IN IMPROVEMENT 24-bit RGB/...
Page 152
EN 152 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.8 Diagram B06C, T6TF4HFG (IC 7GE2) Block Diagram Contrast Reserve Input Proc Contr, Brightness & & Clip Measure MVL manager White-point corr Color LUT Color gamut & Dithering...
Page 153
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q528.1E LA EN 153 9.10.9 Diagram B08E, AD8191ASTZ (IC 7J27) Block Diagram Pin Configuration G_16840_098.eps 090207 Figure 9-31 Internal block diagram and pin configuration...
Page 154
EN 154 Q528.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.10 Diagram B10A, ISP1562BE (IC 7N00) Block Diagram PME# 77, 98, 100 CC(I/O)_AUX PCICLK GLOBAL CONTROL 10, 12 to 15, 20 to 22, AD[31:0] 26 to 31, 33, 34,...
Spare Parts List Q528.1E LA EN 155 10. Spare Parts List Set Level per Model Number (CTN) 2003 4822 124 80061 1000μF 20% 25V 3038 3198 021 38220 8.2kΩ 5% 0.062W 0603 2007 4822 126 14583 470nF 10% 16V 0805 3040 3198 021 38220 8.2kΩ...
Need help?
Do you have a question about the Q528.1E and is the answer not in the manual?
Questions and answers