Related Manuals for Mobiltech i-Sat
Summary of Contents for Mobiltech i-Sat
- Page 1 Mounting and usage instructions Digital Satellite Antenna Mounting and usage instructions Page 1 of 12...
-
Page 2: Table Of Contents
Mounting and usage instructions Summary Introduction ............................3 Safety instructions ..........................3 2.1. Proper use (for the intended purpose) .................... 3 2.2. Safety during installation work ...................... 3 2.3. Proper installation and safety ......................4 2.4. Adhesive sealant ..........................4 2.5. -
Page 3: Introduction
Proper use (for the intended purpose) The i-Sat is designed to receive digital TV and radio programs via satellite. The turntable can be used to receive digital TV and radio signals in the frequency range from 10.70 to 12.75GHz. Any... -
Page 4: Proper Installation And Safety
2mt, or the antenna unit projects beyond the outer lateral outline of the vehicle. The maximum eligible height of 4mt (vehicle and antenna unit) must not be exceeded. 3. Certifications i-Sat complies with the following regulations: Electromagnetic compatibility: EN55022, EN55024 Safety:... -
Page 5: Package Contents
Mounting and usage instructions 4. Package contents The received package contains the following items: External unit with antenna Remote control Fixing plate Power supply cable Cable (4mt) for the connection with external unit Mounting and usage instructions 11mm wrench for F connectors Wrench for security screw 5. -
Page 6: External Unit Space Requirements
Mounting and usage instructions 6.1.2. External unit space requirements Be sure that there is enough space for the folded up system and for the complete rotation of the antenna. For a complete rotation of the antenna during the normal operation the roof of the vehicle must be free of obstacles. -
Page 7: Passing The Cables Through The Roof
Mounting and usage instructions The assembly plate must be glued to the roof using a commercially available sealing compound. For the cleaning of the roof and the assembly plate use a special cleaning agent recommended by the manufacturer of the sealing compound (e.g. SikaFlex 252, Teroson 1K-Pur). After the sealing compound has been dried, apply the sealing compound to the bottom of the plate and strongly apply the plate to the roof of the vehicle. -
Page 8: Protection Circuit
Mounting and usage instructions In the following picture is displayed the electric diagram: 6.1.7. Protection circuit IMPORTANT In order to avoid damages by inadvertently driving with the external unit folded-up, connect the yellow cable to the +15 vehicle line or the D+ line that carries voltage when the engine is on and no-voltage when the engine is switched off. -
Page 9: Mounting On A Mobile Position
Mounting and usage instructions 6.2. Mounting on a mobile position Execute the following steps: Position the antenna and the fixing plate on a plain surface, free of obstacles in the satellite direction. For an outdoor usage is available a specific optional tripod. -
Page 10: Skew Or Cross-Polarization Tuning
Mounting and usage instructions 7.4. Skew or cross-polarization tuning Thanks to the new advanced technologies, the area where it’s possible to receive correctly a satellite signal is increasing more and more. All Europe dedicated TV satellites obviously point their signals over Central Europe. When the receiver – your caravan – is outside this area, the antenna looks at the satellite by side, from a certain “angle”. -
Page 11: Power Off
Mounting and usage instructions Every time there’s a mode/controlled motor switch, the red and green leds are switched on. Release the buttons as soon as the mode/motor is changed, to avoid system reset 7.6. Power off To close the antenna and switch off the system press the ON/OFF key for 3 seconds. For a better safety the system will automatically switch to stand-by status, closing the antenna dish, when the vehicle engine is started. -
Page 12: Reset Alarm Condition
Mounting and usage instructions 7.7.3. Clear alarm condition When an alarm is detected, it’s possible to clear the alarm condition pressing the ON/OFF key for more than 3 seconds but less than 6 seconds. ATTENTION If the ON/OFF key is pressed for more than 6 seconds the whole system will be reset...
Need help?
Do you have a question about the i-Sat and is the answer not in the manual?
Questions and answers