Page 1
O R E N Z SERIES DEEPMAX com Operating manual X5 /X6 Lorenz Detecting Systems GmbH & Co. KG Metal Detectors for professional, industrial and security applications Röpkestrasse 12 D - 30173 Hannover / Germany Tel : +49 (0)5 11 5 51 06 70 Fax : +49 (0)5 11 5 51 06 71 mail@metaldetectors.de...
LORENZ DEEPMAX X5 / X6 Correspond to the following EC requirements: EC-EMC-directive version 89/336/EEC The LORENZ DEEPMAX X5 / X6 series are found to meet the specification requirements detailed, when tested to the customers/ specification requirements. Compatible norms are in particular Test Specifications &...
O R E N Z SERIES DEEPMAX com The LORENZ DEEPMAX X5 and X6 seies detectors are by a specially developed LC Display and a minimum some of the newest developments in the field of Pulse amount of controls. At the same time this detector model GBS metal detectors.
Page 4
LORENZ DEEPMAX X5/X6 in the ground. The LORENZ DEEPMAX X5/X6 will be able without any adjustments. to locate objects at almost the same depths either in most types of ground or ”in air tests”.
Page 5
Saltwater, conjunction with small coils the LORENZ DEEPMAX most types of ground or temperature changes will X5/X6 is a great tool when searching for small only slightly affect the detection range of the objects deep in the ground.
3. Controls on the front panel / short instructions The front panel controls of the two detectors X5 and X6 this button also acts as a start and stop button when are the same, namely three push buttons with ZERO, taking field data with each track.
Page 7
FREQ With this function the preset operation frequency of the LORENZ DEEPMAX X5/X6 can be altered. This is Display mainly necessary when searching near power lines, The Deepmax X5/X6 offers a huge number of functions which cause low frequency interference.
Flashing antenna means no valid GPS data available. Flashing USB means problem occurred with storing data. The Deepmax X5/ X6 series detectors offer two different 5. Start collecting field data in the left corner of the new target identifications namely a FE Ferrous/ NON-FE...
Page 9
The plug of the supplied battery pack has to be connected with this jack. The operation time of the LORENZ DEEPMAX X5/X6 on a fully charged battery pack at 000-099 TIME DELAY reading normal temperature range is approximately 5 to 10 hours A time delay reading which is mainly derived from the depending on the coil connected.
Page 10
USB Jack Version X5 function in order to record different signal data during In order to update the firmware of the Deepmax X5 the operation. For operation a supplied hard- and software supplied USB- Stick can be used to flash the built- in kit will be necessary.
DEL As the LORENZ DEEPMAX X5/X6 offers highest sensitivity with correctly tuned electronics, one should check the 3 for example.
Page 12
Although mounted coils. The coil has to be hold with two adjustable the response speed of the LORENZ DEEPMAX X5/X6 is carrying straps at a constant height over the ground. very fast, the search speed should not exceed 2 meters The search mode can now be selected to a DEL or GND per second.
Page 13
D coils are in use an additional FE ferrous / NON-FE non-ferrous indication will appear on the LC Display. Therefore the Deepmax X5/6 has to be ground balanced with the GB control first as shown 5.1.
Page 14
The time delay target classification of the LORENZ DEEPMAX l Slowly move the search coil from the side at con- X5/X6 will work with all available coils. It is capable to stant height towards the located target. Try to find identify deeply buried big metal objects and small objects the centre of the target with the audio signal.
Page 15
26cm double D search coil Different search coils can be connected to the LORENZ DEEPMAX X5/X6 for special search and location purposes. A special double D version of this coil with separate In general small search coils offer great detection depths transmitting and receiving coils is also available.
Page 16
Those extreme depth ranges on medium sized and bigger operating the LORENZ DEEPMAX X5/X6 to avoid false metal objects make frame mounted search coils signals.
Page 17
The LORENZ x 20 cm pointing towards the coil. Smaller targets will be DEEPMAX X5/X6 is specialy sensitive to many non-ferrous located less effectively than with a 1m x 1m frame. This is metal objects no matter which coil is connected.
Page 18
The LORENZ DEEPMAX X5/X6 will work very stable with this particular coil. The maximum detection depth is limited and below a 1m x 1m frame coil.
Note: Do never forget to turn off the LORENZ DEEPMAX charger. A permanent rorange light indicates the standard X5/X6 when it is not in use or when planing to store it. state- charging. A green light indicates charging finished- Disconnect all plugs from the control box when trickle charge.
Page 20
The LORENZ X5/X6 interferences could also be expected. In general DEEPMAX X5/X6 has to be tuned and the right coil interference will increase with the size of the search has to be chosen first before starting to identify metal coil.
Do switch off the LORENZ DEEPMAX temperature changes. All search coils available for the X5/X6 when the beep alarm sound comes on. Dis- LORENZ DEEPMAX X5/X6 are waterproof. When regarding this can damage the built- in battery. Damages...
Page 22
O R E N Z SERIES DEEPMAX com 10. Detection depths I 26cm- 35cm 35cm- 45cm- 1m double frame 1,5m double frame Used Searchcoil DD-coil GND2* coil DD-coil coil square square Metal object Gold nugget d = 5 mm 22 cm 23 cm 28 cm (23 cm) X...
Page 23
O R E N Z SERIES DEEPMAX com 10.1 Detection depths I I 26cm- 35cm 45cm- 1m double frame 1,5m double frame Used Searchcoil coil DD-coil coil square square Metal object Gold nugget d = 5 mm 15 cm 15 cm Silver coin d = 1,3 cm 22 cm...
Page 24
Therefore frames of 1m x 1m or even bigger should be in metal objects and ground conditions will give for example. use to achieve best results. Recording field data with the Lorenz Deepmax X6 datalogger and Surfer Software Start/Stop Stop...
Page 25
O R E N Z SERIES DEEPMAX com Operating procedures: 5. Start collecting field data in the left corner of the new field by pressing the ZERO button and immediately start To record field data, find a starting point where X and Y lines will meet.
Page 26
Up to In order to change from M Meter to TR Track, FI 99 fields can be generated with the Lorenz Deepmax Field, HDG Heading indication simply alter the X6. The current field will be displayed by the way of SELECT rotary control.
1m x 1m frame coil (collapsed): Carrying case with 110 cm x 15 cm x 15 cm LORENZ DEEPMAX X5/X6 inside: approx. 7000 g 35 cm search coil with extended S-rod: length: 150 cm Telescopic S pole: approx.470 g 35cm search coil with collapsed S-rod: length: 120 cm...
Need help?
Do you have a question about the X5 and is the answer not in the manual?
Questions and answers