Download
Share
Print this page
Sanyo VPC-CA6OR Service Manual
  1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Camcorder
  5. VPCCA6OR
  6. Service manual

Sanyo VPC-CA6OR Service Manual

Digital movie camera ac adaptor
Hide thumbs Also See for VPC-CA6OR:

Advertisement

Quick Links

Download this manual See also: Instruction Manual
SERVICE MANUAL
Digital Movie Camera
AC Adaptor
Contents
1. OUTLINE OF CIRCUIT DESCRIPTION ............................... 3
2. DISASSEMBLY ................................................................... 12
3. ELECTRICAL ADJUSTMENT ............................................. 17
5. TROUBLESHOOTING GUIDE ............................................ 22
6. PARTS LIST ........................................................................ 23
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS ........... C1
RoHS
•This product does not contain any hazardous substances prohibited by the RoHS
Directive.
WARNING
•You are requested to use RoHS compliant parts for maintenance or repair.
•You are requested to use lead-free solder.
(This product has been manufactured using lead-free solder. Be sure to follow the
warning given on page 2 when carrying out repair work.)
CAUTION : Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Discard used batteries according to the manufacturer's instructions.
NOTE : 1. Parts order must contain model number, part number, and description.
2. Substitute parts may be supplied as the service parts.
3. N. S. P. : Not available as service parts.
Design and specification are subject to change without notice.
SX817/U, EX, EX2, EX3 SVA07/U, EX (R)
FILE NO.
VPC-CA6OR
(Product Code : 168 056 01)
(U.S.A.) (Canada) (Korea) (Taiwan)
VPC-CA6EXOR
(Product Code : 168 056 02)
(Europe) (U.K.) (South America)
(China) (Australia) (Hong Kong)
(Russia) (Middle East) (Africa)
(General) (Korea) (Taiwan)
VPC-CA6EX
(Product Code : 168 056 06)
(Europe) (U.K.) (South America)
(China) (Australia) (Hong Kong)
(Russia) (Middle East) (Africa)
(General) (Korea) (Taiwan)
VPC-CA6EXBL
(Product Code : 168 056 08)
(Europe) (U.K.) (South America)
(China) (Australia) (Hong Kong)
(Russia) (Middle East) (Africa)
(General) (Korea) (Taiwan)
VAR-G8U
(Product Code : 126 301 33)
(U.S.A.) (Canada) (Korea) (Taiwan)
VAR-G8EX
(Product Code : 126 301 34)
(Europe) (U.K.) (South America)
(China) (Australia) (Hong Kong)
(Russia) (Middle East) (Africa)
(General) (Korea) (Taiwan)
REFERENCE No. SM5310676

Advertisement

loading

Related Manuals for Sanyo VPC-CA6OR

Summary of Contents for Sanyo VPC-CA6OR

  • Page 1: Table Of Contents

    FILE NO. SERVICE MANUAL VPC-CA6OR Digital Movie Camera (Product Code : 168 056 01) AC Adaptor (U.S.A.) (Canada) (Korea) (Taiwan) VPC-CA6EXOR (Product Code : 168 056 02) (Europe) (U.K.) (South America) (China) (Australia) (Hong Kong) (Russia) (Middle East) (Africa) (General) (Korea) (Taiwan)
  • Page 2 PRODUCT SAFETY NOTICE The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of special significance to product safety. Should any component designated by a symbol need to be replaced, use only the part designated in the Parts List.

  • Page 3: Outline Of Circuit Description

    1. OUTLINE OF CIRCUIT DESCRIPTION Pin 1 1-1. CCD CIRCUIT DESCRIPTION 1. IC Configuration The CCD peripheral circuit block basically consists of the fol- lowing ICs. IC903 (MN39830PMJ-A) CCD imager IC901 (AN20112A) V driver IC905 (AD9996BBCZ) CDS, AGC, A/D converter, H driver Pin 13 2.
  • Page 4 3. IC901 (V Driver) 4. IC905 (H Driver, CDS, AGC and A/D converter) In addition the XV1-XV6 signals which are output from IC101 IC905 contains the functions of H driver, CDS, AGC and A/D are vertical transfer clocks, and the XSG signal is superim- converter.
  • Page 5 1-2. CP1 and VF1 CIRCUIT DESCRIPTION 1. Circuit Description When the TG/SG drives the CCD, picture data passes through 1-1. Digital clamp the A/D and CDS, and is then input to the ASIC as 10-bit The optical black section of the CCD extracts averaged val- data.
  • Page 6 4. Lens drive block 5. Video clip recording and playback 4-1. Focus drive 5-1. Recording The 16-bit serial data signals (LENS_SD) and (LENS_CK and The signals from the camera block are input to the ASIC where LENS_EN) which are output from the ASIC (IC101) are used they are processed, and the image data that is stored in the to drive (FOCUS A +, FOCUS A -, FOCUS B + and FOCUS B IC103 SDRAM is input to the IC102 MPEG4 CODEC LSI.
  • Page 7 1-3. CP2 POWER CIRCUIT DESCRIPTION 1. Outline 3. Analog System Power Output This is the main power circuit, and is comprised of the follow- 12 V (A) is output. Feedback for the 12 V (A) is provided to the ing blocks. switching controller (Pin (3) of IC501) so that PWM control Switching controller (IC501) can be carried out.
  • Page 8 1-4. CP2 STROBE CIRCUIT DESCRIPTION 1. Charging Circuit 2. Light Emission Circuit When UNREG power is supplied to the charge circuit and the When FLCLT signal is input from the ASIC, the stroboscope CHG signal from microprocessor becomes High (3.3 V), the emits light.
  • Page 9 1-5. SYA CIRCUIT DESCRIPTION 1. Configuration and Functions For the overall configuration of the SYA block, refer to the block diagram. The SYA block centers around a 8-bit microprocessor (IC301), and controls camera system condition (mode). The 8-bit microprocessor handles the following functions. 1.
  • Page 10 KEY_MENU Key input MENU (L= input) KEY_1ST Key input 1st SHUTTER (L= input) NOT USED NOT USED NOT USED NOT USED BAT_OFF Battery OFF detection (L= battery OFF) Serial communication request signal SREQ KEY_POWER Key input POWER (L= input) KEY_2ND Key input 2nd SHUTTER (L= input) RESET Reset input (L= reset)
  • Page 11 3. Power Supply Control The 8-bit microprocessor controls the power supply for the overall system. The following is a description of how the power supply is turned on and off. When the battery is attached, a regulated 3.2 V voltage is normally input to the 8-bit microprocessor (IC301) by IC302, so that clock counting and key scanning is carried out even when the power switch is turned off, so that the camera can start up again.

  • Page 12: Disassembly

    2. DISASSEMBLY 2-1. REMOVAL OF CABINET LEFT AND CP2 BOARD 1. Two screws 1.7 x 5 7. Two screws 1.7 x 6 13. Remove the solder. (from strobo) 2. Dec grip 8. Cabinet left 14. Remove the solder. (from trans) 3.
  • Page 13 2-2. REMOVAL OF VF1 BOARD AND LCD 1. FPC 9. Spacer FPC gasket 2 16. Two screws 1.7 x 3.5 2. Cap joint 10. Spacer LCD back 17. Holder mic 3. Assy joint LCD 11. FPC 18. Two microphones 4. Remove the assy LCD front 12.
  • Page 14 2-3. REMOVAL OF LENS ASSEMBLY, CP1 BOARD AND CA1 BOARD 1. Screw 1.7 x 3 8. Screw 1.7 x 4 15. Spring batt eject 2. Screw 1.7 x 4 9. Two screws 1.7 x 4 16. Terminal batt 3. Earth speaker 10.
  • Page 15 2-4. REMOVAL OF CABINET RIGHT 1. Spacer flash 2. Compl, holder flash 3. Screw 1.7 x 2.5 4. Holder speaker 5. Speaker, 8 6. Screw 1.7 x 2.5 7. Earth unit back 8. Cabinet right 9. Assy unit back FPC 10.
  • Page 16 2-5. BOARD LOCATION VF1 board CA1 board CP1 board CP2 board – 16 –...

  • Page 17: Electrical Adjustment

    3. ELECTRICAL ADJUSTMENT 3-4. Setup 3-1. Table for Servicing Tools 1. System requirements Part code Windows 98 or Me or 2000 or XP Ref. No. Name Number IBM R -compatible PC with pentium processor Pattern box (color viewer) VJ8-0190 CD-ROM drive VJ8-0297 Calibration software USB port...
  • Page 18 3-6. The adjustment item which in necessary in part exchange CCD Black Point CCD White Point And White Point USB storage Factory Lens Language Reset Defect Detect information Defect Detect Cord Setting Adjustment Setting Adjustment Adjustment In Adjustment registration Setting Lighted COMPL PWB CP-1 COMPL PWB CP-2...
  • Page 19 2. AWB Adjustment Adjustment value determination 50<a1<310, 100<a2<550, 200<a3<750, 300<a4<950, 400<a5<1024 wc0=128 ± 2, wc1=128 ± 2, wc2=130 ± 40 wnc0=128 ± 2, wnc1=128 ± 2, wnc2=130 ± 40 801<ms1<=2500, 1201<ms2<=2900, 1251<ms3<=3100, 1401<ms4<=3600 100<=s1<=220, 100<=s2<=220, 100<=s3<=220, 100<=s4<=220, 100<=s5<=220 s1>s2>s3>s4>s5 0<=g<=255 0<=o<=255 Adjustment values other than the above are irrelevant.
  • Page 20 3-8. Factory Code Setting 3-12. Firmware uploading procedure 1. Check the "Factory Code" display within the Setting group. 1. Uploading the firmware should be carried out if the version 2. For U.S.A., Canada and NTSC general area number (COMPL PWB XX-X) on the replacement circuit If "FC_SANYO_U"...

  • Page 21: Usb Storage Information Registration

    17.) 2. Double-click on the DscCalDi.exe. 3. Click on the Get button in the USB storage window and check the USB storage data. VID: SANYO PID: CA6 Serial: Rev. : 1.00 4.

  • Page 22: Troubleshooting Guide

    5. TROUBLESHOOTING GUIDE POWER LOSS INOPERTIVE TAKING INOPERATIVE PUSH SHUTTER PUSH THE POWER BUTTON SW FOR A WHILE HIGH IC301-44, 52 IC301-51 CHECK UNIT SW CHECK UNIT SW KEY INPUT KEY INPUT IC501-18, 29 CHECK IC101, IC301, IC302-7 5.3 V CHECK CP2, IC531, (P ON, PA ON) PWA BLOCK...

  • Page 23: Parts List

    CABLE,DSC USB 9053 636 096 7243 INSTRUCTION MANUAL(English) (CAMERA APPRICATION SOFTWARE) PACKING MATERIALS LOCATION PARTS NO. DESCRIPTION 636 096 9339 CARTON INNER-SX817/EX,EXCEPT VPC-CA6OR 636 096 9322 CARTON INNER-SX817/U,VPC-CA6OR ONLY 636 078 4659 CUSHION SHEET-SX792/KRNK 636 096 9261 REINFORCE PAD,A-SX817/J (BOTTOM)
  • Page 24 ADHESIVE FPC GASKET-SX817 636 098 8934 DEC LCD A-SX817/J2,VPC-CA6EX ONLY 636 099 0654 ASSY,LCD FRONT-SX817/J, 636 098 0365 COMPL PWB,CP-2 F/W VPC-CA6OR,VPC-CA6EXOR 636 096 8516 SPACER FPC CA1-SX817/J 636 099 1170 ASSY,LCD FRONT-SX817/J2,VPC-CA6EX ONLY 636 096 5164 HOLDER STRAP-SX817/J 636 099 1507...
  • Page 25 Cabinet 1 SX817/J PARTS LIST 1...
  • Page 26 CABINET AND CHASSIS PARTS 2 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION 636 096 5485 HOLDER CP2-SX817/J 636 099 0579 ASSY,CABI RIGHT-SV, EXPECT VPC-CA6EX 636 097 9826 COMPL PWB,CP-1 F/W 636 099 9220 ASSY,CABI R-SX817/J2-SV,VPC-CA6EX ONLY 636 099 3570 HOLDER CP1-SX817/J 636 096 5522 SPRING BATT EJECT-SX817/J...
  • Page 27 Cabinet 2 SX817/J PARTS LIST 2...
  • Page 28 ELECTRICAL PARTS Note: 1. Materials of Capacitors and Resistors are abbreviated as follows ; Resistors Capacitors MT-FILM Metallized Film Resistor MT-POLYEST Metallized Polyester Capacitor MT-GLAZE Metallized Glaze Resistor MT-COMPO Metallized Composite Capacitor OXIDE-MT Oxide Metallized Film Resistor TA-SOLID Tantalum Solid Capacitor AL-SOLID Aluminum Solid Capacitor NP-ELECT...
  • Page 29 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION L1301 945 072 7413 IMPEDANCE,90 OHM - C9712 303 294 6100 CERAMIC 100P J 50V L1302 945 020 1869 INDUCTOR,750 OHM C9714 303 381 8109 CERAMIC 1U K 6.3V L1303 945 059 8112 IMPEDANCE,1000 OHM P C9716 303 338 0309...
  • Page 30 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION R9505 301 314 0503 MT-FILM 22 FD 1/6W T5402 645 069 2420 TRANS,STEP UP R9506 301 314 0503 MT-FILM 22 FD 1/6W (CAPACITORS) R9507 301 105 7902 MT-GLAZE 0.000 ZA 1/16W C3001 303 391 0506 CERAMIC 10U K 6.3V...
  • Page 31 LOCATI O N PARTS NO. DESCRI P TI O N R5008 301 262 2307 MT-GLAZE 1.0K DC 1/16W R5012 301 262 0600 MT-GLAZE 22K DC 1/16W R5013 301 290 2508 MT-GLAZE 13K DC 1/16W R5014 301 290 1303 MT-GLAZE 750 DC 1/16W R5015 301 284 5805 MT-GLAZE...
  • Page 32 SANYO Electric Co., Ltd. Osaka, Japan Jul./’06...

This manual is also suitable for:

Vpc-ca6exVpc-ca6exblVar-g8uVpc-ca6exorVar-g8ex