Page 1
SERVICE MANUAL HF MARINE TRANSCEIVER iM710...
Page 2
TD62783AF IC-M710 MAIN UNIT 5 pieces 6. DO NOT transmit power into a signal generator or a 8810008560 Screw PH M3×8 SUS ZK IC-M710 Top cover 10 pieces sweep generator. Addresses are provided on the inside back cover for your 7.
SECTION 3 CIRCUIT DESCRIPTION 3-1 RECEIVER CIRCUITS 3-1-3 2ND MIXER AND IF CIRCUITS (MAIN UNIT) The 1st IF signal from the crystal filter (FI1b) is converted 3-1-1 RF FILTER CIRCUIT (MAIN UNIT) again into a 9.0115 MHz 2nd IF signal at the 2nd mixer Received signals from the antenna connector pass through circuit (D52, L66, L67).
Page 7
The detected voltage is also applied to the noise blanker 3-1-8 S-METER CIRCUIT (MAIN UNIT) AGC circuit (Q12, Q10) and is then fed back to the noise The S-meter indicates the AGC level on the display, since amplifier (IC8) as a bias voltage. The noise AGC circuit the AGC level varies with the received signal strength.
The comparator outputs “High” when the integrated signals The SSB signal from FI2 is amplified at the 9 MHz amplifi- exceed the reference voltage. C269, R310 and R780 are ers (Q17–Q19) and is then applied to the mixer circuit (D52). used as a time constant circuit.
Page 9
3-2-6 POWER AMPLIFIER CIRCUIT 3-2-7 ALC CIRCUIT (PA150W BOARD) The transceiver has two ALC (Auto Level Control) loops for constant output power over all marine bands and for high This circuit provides a stable 150 W (at 13.6 V) of output power setting.
3-2-8 APC CIRCUIT 3-3 PLL CIRCUIT The APC (Auto Power Control) circuit protects the power 3-3-1 GENERAL amplifiers on the PA unit from high SWR and excessive The PLL unit generates a 1st LO frequency (69.5115– current. 99.0114 MHz), 2nd LO frequency (60 MHz) and a BFO fre- quency (9.0106–9.013 MHz) for the MAIN unit.
Page 11
(REG UNIT; [EUR] only) Outputs a “SEND” control signal for ASEN The IC-M710 [EUR] version employs a floating ground- the ACC (1) and ACC (2) sockets. ing system which is not connected between transceiver’s Outputs a “SEND” control signal for ground and (–) terminal of the power supply.
Page 12
(MAIN unit; IC132)–Continued Port Description number name Outputs AF gain control signal to the control (IC36). Outputs the "tuner start" pulse to an STAT optional AT-130E. Outputs a BEEP signal (1 kHz or BEEP 500 Hz). Outputs a strobe signal to the main STB1 loop PLL IC (C3005).
Connect pins 3 and 4 to the [PTT] antenna for AF output connector CAUTION: DO NOT connect the signal generator while to DC power receptacle DC power suppy transmitting. 13.6 V/30 A [DC 13.6V] [ANT] IC-M710 to [MICROPHONE] 4 - 1...
4-2 PLL ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST • Display frequency : 7.9999 MHz Connect a digital 3.2 V C3049 REFERENCE • Mode : J3E multimeter or oscillo- LOOP LOCK • Receiving scope to check point VOLTAGE J3004.
Page 15
• MAIN AND PLL UNITS 13.6 V voltage L106 check point C3049 Reference loop lock voltage adjustment J3004 Reference loop lock voltage Reference P3002 check point frequency check point Main loop J3005 L3005 Reference lock voltage L3004 frequency check point L3003 Adjustment Main loop...
4-4 TRANSMITTER ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST IDLING • Display frequency : 12.2300 MHz PA150W Cut the lead wire 100 mA PA150W R4022 CURRENT • Mode : J3E (W4011) and connect (For drive •...
Page 17
• PA AND FILTER BOARDS IC APC check point Ammeter 7 8 9 DC power supply R4022 Idling current (for drive transistors) adjustment R4025 Idling current (for final transistors) Idling current W4011 adjustment (for drive transistors) check point Ammeter EP4004 EP4003 W4011 R4026...
Page 18
TRANSMITTER ADJUSTMENTS (continued) ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST TRANSMIT • Display frequency : 12.2300 MHz Rear C o n n e c t a n R F 140 W MAIN R184 • Mode : A1A [Others] Panel power meter to the GAIN...
Page 19
• MAIN AND LOGIC UNITS Tune power L108 preparation Transmit Tune power R205 gain adjustment R184 adjustment Transmit R159 gain R184 Output power chack point R211 adjustment R212 MIC limitter preparation Carrier R844 suppression R238 adjustment R2066 MIC gain adjustment R2070 MIC limitter adjustment 4 - 7...
4-5 RECEIVER ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST RECEIVER • Display frequency : 2.1820 MHz Rear C o n n e c t a n A C Maximum output level MAIN Adjust in GAIN •...
Page 21
• MAIN UNIT MAIN UNIT Noise blanker adjustment Noise blanker check point R300 Receiver gain R257 preset Receiver gain R223 adjustment R223 Total gain adjustment 4 - 9...
Page 26
[MAIN UNIT] [MAIN UNIT] ORDER ORDER DESCRIPTION DESCRIPTION Ω L122 6180001710 COIL LAL 03NA 561K 7010004450 RESISTOR R20J 100 k Ω L123 6200003020 S.COIL NL 322522T-R33J-3 7030003640 S.RESISTOR ERJ3GEYJ 473 V (47 k Ω L124 6200003000 S.COIL NL 322522T-R22J-3 7030003540 S.RESISTOR ERJ3GEYJ 682 V (6.8 k Ω...
Page 27
[MAIN UNIT] [MAIN UNIT] ORDER ORDER DESCRIPTION DESCRIPTION Ω Ω R158 7030003560 S.RESISTOR ERJ3GEYJ 103 V (10 k R255 7030003520 S.RESISTOR ERJ3GEYJ 472 V (4.7 k Ω Ω R159 7010004340 RESISTOR R20J 15 k R256 7030003320 S.RESISTOR ERJ3GEYJ 101 V (100 Ω...
Page 28
[MAIN UNIT] [MAIN UNIT] ORDER ORDER DESCRIPTION DESCRIPTION Ω Ω R372 7030003440 S.RESISTOR ERJ3GEYJ 102 V (1 k R603 7030003440 S.RESISTOR ERJ3GEYJ 102 V (1 k Ω Ω R373 7030003760 S.RESISTOR ERJ3GEYJ 474 V (470 k R604 7030003760 S.RESISTOR ERJ3GEYJ 474 V (470 k Ω...
Page 29
[MAIN UNIT] [MAIN UNIT] ORDER ORDER DESCRIPTION DESCRIPTION Ω Ω R733 7030003680 S.RESISTOR ERJ3GEYJ 104 V (100 k R831 7030003560 S.RESISTOR ERJ3GEYJ 103 V (10 k Ω Ω R734 7030003680 S.RESISTOR ERJ3GEYJ 104 V (100 k R832 7030003560 S.RESISTOR ERJ3GEYJ 103 V (10 k Ω...
8210012192 1632 front panel-1 [GMDSS] W1012 8900006082 Cable OPC-567B MP2802 8310035581 1632 window plate MP2803 8930035591 1632 3-key-1 MF1001 2710000520 Fan SB0812H-ICOM-00 [Others] MP2804 8930035600 1632 4-key 2710000570 Fan VFA-8018-BH10-1000 [GMDSS] MP2805 8930035610 1632 14-key MP2806 8930035640 1632 power key...
Page 44
[PA PARTS] [MAIN UNIT] REF. ORDER REF. ORDER DESCRIPTION QTY. DESCRIPTION QTY. F4601 5220000210 Holder FH-052S 8510000230 220 shield case F4602 5220000210 Holder FH-052S 8510000241 220 shield case cover -1 F4603 5210000090 Fuse FGB 30A 8510002200 VCO case F4604 5210000090 Fuse FGB 30A 8510000230 220 shield case...
Page 45
[GEN-21], [GEN-22], [EUR-21] versions MP4611 MP4635 MP4639 MP4640 (C): CHASSIS PARTS MP4636 (P): PA UNITS (PA): PA150W BOARD MP4609 (F): FILTER BOARD (R): REG BOARD (M): MAIN UNIT (PL): PLL UNIT W1012 MP1003 MP4636 W1012 MP1029 F7001(R) MP4631 MP4602 MP1045 MP1030 MP1051 F7002 (R)
Page 46
[GEN-23], [EUR-22] versions MP4611 MP4635 MP4639 MP4640 MP4636 (C): CHASSIS PARTS MP4609 (P): PA UNITS (PA): PA150W BOARD (F): FILTER BOARD (R): REG BOARD (M): MAIN UNIT (PL): PLL-A UNIT W1012 MP4636 MP1003 MP1029 MP1047 W1012 MP1056 MP1046 F7001(R) MP4602 MP4646 (P) MP1051 MP1045...
Page 47
SECTION 7 SEMI-CONDUCTOR INFORMATION • TRANSISTOR AND FET’S • DIODES 2SA1037K WT R 2SA1213 Y 2SA1586 GR 2SB1015 Y 2SC1623 L6 1SS55 1SS133 1SS165 1SS184 1SS226 (Symbol: FR) (Symbol: NY) (Symbol: SG) (Symbol: L6) (Symbol: Green line) (Symbol: Yellow line) (Symbol: Green line) (Symbol: B3) (Symbol: C3)
Page 48
SECTION 8 BOARD LAYOUTS 8-1 LOGIC UNIT • TOP VIEW TX FREQ 2182kHz /RESET MODE ALARM FUNC TUNE SPEAKER DIMMER Add "2000" to each indicated part number NOTE: on the unit for the actual number. 8-2 SENSOR1/2 BOARDS 8-3 MIC BOARD 8-4 VR1 BOARD 8-5 VR2 BOARD •...
Page 49
• BOTTOM VIEW (LOGIC UNIT) J2003 to MAIN unit J23 J2008 PTTE MICE to MIC board J2302 J2002 to MAIN unit J16 J2007 to FRONT SP2801 J2012 J2011 J2009 J2010 to VR1 board J2401 J2013 HVO/GND 1 J2016 to VR2 HV/13S board J2501 from TERMINAL...
Page 50
8-6 MAIN UNIT • TOP VIEW from REG board P8002 [EUR-21] /from TERMINAL 13.6 board J7001 P4001 [GEN-21], [GEN-22] from PA150W board J4001 from LOGIC /from LOGIC REMOTE P4302 unit J2002 unit P2004 (DSC) NBDP from FILTER [GEN-23], [EUR-22] board J4302 ACC1 ACC2 CLONE...
Page 52
8-7 PLL UNIT (for [GEN-21], [GEN-22], [EUR-21]) • TOP VIEW J3007 P3001 to MAIN unit J3 to MAIN unit J9 P3003 Add "3000" to each indicated part number P3002 NOTE: to MAIN unit J5 on the unit for the actual number. to MAIN unit J4 8 - 5...
Page 54
8-8 PLL-A UNIT (for [GEN-23], [EUR-22]) • TOP VIEW J3007 J3008 P3001 to LOGIC to MAIN unit J3 unit J2016 to MAIN unit J9 MP3016 P3003 Add "3000" to each indicated part number P3002 NOTE: to MAIN unit J5 on the unit for the actual number. to MAIN unit J4 8 - 7...
Page 56
8-9 PA150W BOARD J4003 • TOP VIEW to MAIN from TERMINAL board unit J22 P4301 from FILTER board J4301 EP11 MP5 C81 EP14 EP14 PA unit MP4645 EP10 EP12 Add "4000" to each indicated part number NOTE: MP4003 MP4003 to MAIN on the unit for the actual number.
Page 57
• BOTTOM VIEW (PA150W BOARD) Add "4000" to each indicated part number NOTE: on the unit for the actual number. 8 - 10...
Page 58
8-10 FILTER BOARD P4301 to PA150W board J4002 J4303 to MAIN unit J19 P4302 P4601 Add "4300" to each indicated part number NOTE: to MAIN unit J2 from PA150W board J4601 on the unit for the actual number. 8 - 11...
Page 59
8-11 TERMINAL BOARD PA unit PA unit PA unit W4603 F4601 F4602 to MAIN unit J32 [GEN-21], [GEN-22] J7001 /to LOGIC HVO/HV 2 unit J2013 [GEN-23] /to REG board P8001 [EUR-21], [EUR-22] EP7008 EP7006 [GEN-23] P7001 EP7009 to PA150W [EUR-22] board EP4009 to LOGIC F7001...
Page 60
8-12 REG BOARD [EUR] only 8-13 ALARM BOARD except [GEN-21] • TOP VIEW • TOP VIEW Vertical J5001 to MAIN unit J29 J5002 to MAIN P8001 P8002 unit J32 [EUR-21] to TERMINAL to MAIN HVO/HV 13.6/13S board J7001 /to LOGIC unit J30 unit J2013 [EUR-22]...
Page 61
• BOTTOM VIEW (ALARM BOARD) • BOTTOM VIEW (REG BOARD) Vertical Add "5000" to each indicated part number NOTE: on the unit for the actual number. 8 - 14...
Need help?
Do you have a question about the IC-M710 and is the answer not in the manual?
Questions and answers