Table of Contents
Advertisement
5
Press ENTER.
The third page is shown, in which the pull-down menu of the
[ANALOG OUT] is already open.
DVD PLAYER SET UP
DIGITAL AUDIO OUTPUT
ANALOG OUT
D. RANGE CONTROL
OUTPUT LEVEL
SELECT
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER
6
Press 5/∞ to select a desired analog output
signal type.
Set this item correctly when you play back a DVD VIDEO disc
recorded with surround multichannel audio.
• When connecting to a surround decoder, select [2-CH
DOLBY SURROUND].
• When connecting to a stereo amplifier/receiver or TV, select
[2-CH STEREO].
• When connecting the unit's 5.1-channel output, select
[MULTI CHANNEL]. Note that you can perform fine tuning
for your speakers when [MULTI CHANNEL] is selected (see
pages 38 and 40).
7
Press ENTER.
The final page is shown, in which the pull-down menu of the
[DIGITAL AUDIO OUTPUT] is already open.
DVD PLAYER SET UP
DIGITAL AUDIO OUTPUT
ANALOG OUT
D. RANGE CONTROL
OUTPUT LEVEL
SELECT
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER
DIGITAL AUDIO OUTPUT options
8
Press 5/∞ to select a desired digital output
signal type.
Set this item correctly when you connect the unit to an
external surround decoder or D/A converter. (If you do not
connect the unit to such a device, you do not have to set this
item.)
• When connecting to other digital device, select [PCM
ONLY].
• When connecting to a Dolby Digital decoder, select
[DOLBY DIGITAL/PCM].
• When connecting to a Dolby Digital decoder or a DTS
decoder, select [STREAM/PCM].
9
Press ENTER.
The TV screen returns to the opening display.
To bring up the DVD PLAYER SET UP display later
Press CHOICE for a few seconds until the DVD PLAYER SET UP
display appears.
To change the brightness of the display window
Press DIMMER on the remote control unit.
You can select the display window and the disc tray brightness
from three levels, or off. If the brightness is set to off, nothing
will be shown on the display.
STREAM/PCM
DOLBY PROLOGIC
2-CH DOLBY SURROUND
ON
2-CH STEREO
MULTI CHANNEL
ANALOG OUT options
DOLBY DIGITAL/PCM
PCM ONLY
DOLBY PROLOGIC
DOLBY DIGITAL/PCM
STREAM/PCM
ON
About screen saver function
A television monitor may have an image burned into it if a static
image is displayed for a long time. To prevent this, the unit
automatically activates the screen saver function if a static
picture, such as an on-screen display or menu, is displayed for
over 5 minutes.
When the screen saver function is activated, the TV screen
gets darker.
Pressing any buttons will release the screen saver function
(see page 37).
Basic playback
1
Press 0 (or OPEN/CLOSE on the remote
control unit) to open the disc tray.
2
Place a disc in the disc tray.
IV E
SS
RE
O G
PR
• To insert an 8-cm disc, place it in the inner recess.
3
Press 3.
The unit starts playback from the beginning.
If a menu is shown on the TV screen
When inserting a DVD AUDIO, DVD VIDEO, SVCD or Video CD
disc, a menu may be shown on the TV screen. From the menu,
you can select a desired item to be played back.
For DVD AUDIO/DVD VIDEO
1 Press 5/∞/2/3 to select a desired item.
2 Press ENTER.
The unit starts playback of the selected item.
For SVCD/Video CD
Press the numeric buttons to select a desired item.
The unit starts playback of the selected item.
NOTES
• Do not insert an unplayable disc. (See page 2.)
• When inserting a disc on the disc tray, be sure to position the
disc inside the recess. Otherwise, the disc may be damaged
when the disc tray is closed, or you may not be able to remove
the disc from the unit.
• When a DVD AUDIO disc is played back, the DVD AUDIO
indicator on the front panel turns on.
• For a double-sided DVD VIDEO disc, place the disc with the
playback side facing down.
Basic operations
With the label side up
11
Advertisement
Table of Contents
