Travel system with seat unit, infant carrier, hood and raincover (14 pages)
Summary of Contents for My Child Floe Convertible Pushchair
Page 1
Floe Convertible Pushchair Chassis and Seat Unit This product is tested to: BS EN 1888:2012 Suitable for children from birth and up to 15kg INSTRUCTIONS: Please read carefully and keep for future reference. Your child’s safety may be affected if you do not...
Page 2
Safety - Bassinette mode Important: Read, understand and follow these instructions carefully and retain for future reference WARNING: To avoid injury ensure that your child is kept away when unfolding and folding this product. WARNING: Do not let your child play with this product. WARNING: Never leave your child unattended.
Page 3
Safety - Seat unit mode Important: Read, understand and follow these instructions carefully and retain for future reference WARNING: To avoid injury ensure that your child is kept away when unfolding and folding this product. WARNING: Do not let your child play with this product. WARNING: Never leave your child unattended.
Note: Do not put in your car on hot days, as this will damage your rain cover. Welcome Thank you for purchasing the MyChild Floe Convertible Pushchair. Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product.
Parts checklist Contained in your carton are: Part Chassis + basket Seat unit Rear wheels Front wheels Bumper bar Hood Apron Mattress Raincover* *Can be found in the zip compartment of basket Optional extras - sold seperately: Maxi Cosi Car Seat Adaptors * style may vary to that shown Floe Infant Carrier page 4...
Front wheel assembly Push the front wheels into the holes at the front of the chassis. Ensure the wheels click into place and check they are firmly attached by pulling them. click To remove, push tab (A) and pull the wheel off (B).
Rear wheel assembly Note: The rear wheels have an axle with a flattened edge (A). Ensure each axle is correctly lined up with the holes at either side of the rear of the chassis and push them into the holes. WARNING: The hole is NOT round.
Page 8
Opening the pushchair (continued) Hold the handles and lift them upwards until the chassis is fully open, ensuring that the chassis clicks into position. click WARNING: Ensure that all the locking devices are engaged before use. click Attaching the seat unit The seat unit can be attached parent facing or forward facing (as shown).
Removing the seat unit To remove the seat unit, press in the release catches (A) on each side of the seat unit and lift the seat unit off the chassis. Adjusting the seat unit recline Press in BOTH buttons (A) located on each side of the seat unit and tilt the seat unit to the required position.
Page 10
Converting to bassinette mode WARNING: DO NOT attempt to convert the seat unit into bassinette mode with a child seated in it. ATTENTION: Strap (D) needs to be unhooked before converting to bassinette mode and MUST be RE-CONNECTED when converting to the seated mode. Remove the seat unit from the chassis, unfasten the three buckles (A, B &...
Attaching the apron Place the apron over the bassinette and connect the velcro on the apron with the velcro on the bassinette sides (A). Fasten the press studs on the apron to the inside of the bassinette frame(B). Converting to seated mode WARNING: DO NOT attempt to convert the bassinette into seated mode with a child seated in it.
Using the brakes To engage the brakes, press down the red brake pedal (A). To disengage the brakes, press down the green release pedal (B). Note: If you hear a rubbing or a clicking noise from one of the rear wheels, then lift brake pedal (A) lightly with your foot, if the noise continues then you may need to tighten the adjustment nut (C) on the...
Adjusting the hood The hood can be partially or fully opened. To open: Pull the front edge of the hood forward. To close: Push the hood back. Bassinette mode: When using the seat in bassinette mode, unzip zip (A) and extend the hood forward.
Attaching the bumper bar Line up both connectors (A) on each side of the bumper bar and push into the mounting brackets (B) until they click in place. Pull the bumper bar to check it is inserted correctly. WARNING: The bassinette is not a carrycot.
Safety harness Clip the shoulder strap clips (A) onto the loop of the waist strap connectors (B). Push the waist strap connectors (B) into the buckle (C) until they click into place. Adjust the sliders (F) on the waist and shoulder straps so that the harness fits snugly.
Page 16
Repositioning the safety harness The shoulder straps and waist straps can be repositioned to suit the size of your child. Use the shoulder straps in one of the three slots that are closest to your child’s shoulder height and position the waist strap in one of the two slots that best suits your child’s waist size.
Repositioning the safety harness (continued) To adjust the crotch strap position closer to the child, slide the buckle under the strip of fabric on the seat. To adjust the crotch strap position further from the child, slide the buckle out from under the strip of fabric on the seat.
Page 18
Your 3 year warranty Whilst we make and test our products to the highest standards of durability there’s always a small chance of a hiccup! Our promise is to repair, replace or refund a MyChild product that has an identified manufacturing defect from the date of purchase for a full 3 years thereafter at no extra cost.
Need help?
Do you have a question about the Floe Convertible Pushchair and is the answer not in the manual?
Questions and answers