Table of Contents
Advertisement
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT
INTRODUCTION
This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas
heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio
frequencies (RF) within a 20-foot range using non-directional signals. The system operates one of 1,048,576 security codes that are
programmed into the transmitter at the factory; the remote receiver's code must be matched to that of the transmitter prior to initial use.
Review COMMUNICATION SAFETY under theTRANSMITTER SECTION and THERMO SAFETY under the REMOTE RECEIVER
SECTION. These signal/temperature safety features shut down the appliance when a potentially unsafe condition exists.
The transmitter operates on (2) AAA-size 1.5V batteries. It is recommended that ALKALINE batteries always be used for
longer battery life and maximum operational performance. IMPORTANT: New or fully charged batteries are essential for
proper operation of the multi-function transmitter. Insert (2) AAA-size 1.5 V batteries into the battery compartment on the
back of the transmitter, positioning the (+) and (-) ends of the batteries as indicated on the casing. When the batteries are
inserted, figure #2 (with similar numbers) will display.
MODE
COVER CLOSED
Fig. 1 Transmitter Front and Back Views
LCD DISPLAY FUNCTIONS
1. BATTERY ICON - Symbol means battery power is low. Replace batteries within 2-weeks.
2. TIMER- Indicates time remaining before system shuts OFF, when timer-programmed; 9-hour maximum setting.
3. MODE- Indicates operation MODE of system. ON indicates the system is manually ON. OFF indicates the entire
system is turned OFF and THERMO indicates the system will automatically cycle ON/OFF, depending on the SET
temperature.
4. SET- Indicates desire SET room temperature for THERMO operation.
5. FLAME – Indicates burner/valve in ON position.
6. CLOCK – Indicates the current time in AM/PM
7. ROOM – Indicates CURRENT room temperature.
8. °F indicates degrees Fahrenheit (°C indicates degrees Celsius).
Skytech: 3002
Model: 3002
INSTALLATION AND OPERATING INSTRUCTIONS
TO INSTALL OR OPERATE
+
SLIDE COVER
BACK OF
OPEN
TRANSMITTER
Note: If a LOW battery icon appears on the screen,
check the position of the batteries.
CAUTION: Due to the sensitive temperature-monitoring
components in the transmitter, it may be necessary to
allow the transmitter to stabilize to room temperature
before accurate room temperatures are displayed on
the screen. If the transmitter is activated from a
severe cold condition, it can take up to fifteen minutes
for accurate temperature readings to appear.
-
1
8
-
+
7
Fig. 2 LCD Display Functions
2
3
SET
ROOM
6
REV. 4-19-12 Page 1
4
5
Advertisement
Table of Contents
Related Manuals for Skytech 3002
Summary of Contents for Skytech 3002
- Page 1 TO INSTALL OR OPERATE INTRODUCTION This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio frequencies (RF) within a 20-foot range using non-directional signals.
-
Page 2: Setting Up The Transmitter
You may also press the ROOM SET button on the transmitter to stop the time digits from blinking and set the time. Fig. 9 Setting Minutes Fig. 8 SettingHours Skytech: 3002 REV. 4-19-12 Page 2... -
Page 3: Remote Receiver
This remote control system must be installed exactly as outlined in these instructions. Read all instructions completely before attempting installation. Follow instructions carefully during installation. Any modifications of the SKYTECH remote control or any of its components will void the warranty and may could cause a fire hazard. -
Page 4: Installation Instructions
LEARNED the transmitter’s security code (see LEARNING TRANSMITTER TO RECEIVER). Cover Plate (Rear View) Remote Receiver Fig. 12. Wall plate to Receiver Receiver Slide Button Cover Plate Plastic Switch Box Fig. 13. Installing receiver into switch box. Skytech: 3002 REV. 4-19-12 Page 4... -
Page 5: Hearth Mount
OFF REMOTE ON attempt, wait 1-2 minutes before trying again – this delay allows the microprocessor to reset its timer circuitry – and try up to two or three more times. Fig. 16 Learning Skytech: 3002 REV. 4-19-12 Page 5... -
Page 6: System Check
TRANSMITTER TRANSMITTER OPERATING DISTANCE The SKYTECH remote control operates on RF (radio frequency) signals that are sent by the TRANSMITTER (remote) to the RECEIVER that operates the appliance. It is recommended that the TRANSMITTER always be located within the 20-foot operating range, preferably in the same room in which the appliance is located. - Page 7 COMMUNICATION SAFETY FEATURE IN TRANSMITTER This SKYTECH series remote controls have a COMMUNICATION – SAFETY function built into the software. It provides an extra margin of safety when the TRANSMITTER is out of the normal 20-foot operating range of the receiver.
-
Page 8: Setting The Countdown Timer
(Fig. 20). At this time, approximately two weeks of battery power remains until the transmitter may experience partial or complete loss of functions. ROOM Fig. 20 Low Battery Sign Skytech: 3002 REV. 4-19-12 Page 8... -
Page 9: Battery Life
Should you encounter problems with your fireplace system, the problem may be with the fireplace itself or it could be with the SKYTECH remote control. Review the fireplace manufacturer’s operation manual to make sure all connections are properly made. Then check the operation of the SKYTECH remote in the following manner: 1. -
Page 10: Specifications
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. FOR TECHNICAL U.S. INQUIRIES CANADIAN INQUIRIES SERVICE, CALL: (888) 672-8929 or (877) 472-3923 (260) 459-1703 Website: www.skytechsystem.com MANUFACTURED EXCLUSIVELY FOR SKYTECH II, INC Skytech: 3002 REV. 4-19-12 Page 10...
Need help?
Do you have a question about the 3002 and is the answer not in the manual?
Questions and answers