MTHTrains Z-4000 Operating Instructions Manual

Z-4000 400-watt transformer

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

M.T.H. Electric Trains®

Z-4000 400-Watt Transformer

Operating Instructions

The M.T.H. Z-4000® Transformer is a state-of-the-art UL-approved 400-watt

model railroad hobby transformer. It features a microprocessor-controlled

interface that provides the model railroader unprecedented control over any AC-

powered model locomotive and locomotive sound system. The Z-4000

transformer may be used alone for local control of a model railroad or it can be

paired with a remote control system, such as the M.T.H. Z-4000 Remote Control

System or the M.T.H. DCS Remote Control System. Operators of any AC

powered O, S, or Standard Gauge locomotive, regardless of manufacturer, will

appreciate the power and control features found in the Z-4000 transformer. For

your own safety and that of your equipment, please read the following pages

before beginning to use your Z-4000 Transformer.

CAUTION-ELECTRICALLY

OPERATED PRODUCT:

Not recommended for children under 10

years of age. M.T.H. recommends adult

supervision with children ages 10-16. As

with all electric products, precautions

should be observed during handling and

use to reduce the risk of electric shock.

Table of Contents

Need help?

Do you have a question about the Z-4000 and is the answer not in the manual?

Questions and answers

Summary of Contents for MTHTrains Z-4000

Page 1 M.T.H. Z-4000 Remote Control System or the M.T.H. DCS Remote Control System. Operators of any AC powered O, S, or Standard Gauge locomotive, regardless of manufacturer, will appreciate the power and control features found in the Z-4000 transformer.
Page 2 The Z-4000 Transformer’s control panel has a voltage display, amperage display, and horn, bell, direction, and programming buttons for two track outputs. Two additional fixed voltage outputs are also available, making the Z-4000 the perfect choice for operating O, S, or Standard Gauge locomotives and accessories.
Page 3 Outside (-) Rail Connect To Track Center (+) Rail Once the track and/or accessories have been wired up to the Z-4000, plug the AC power cord into any 110V household plug and follow the remaining operating instructions. Note: The owner should not, at any time, attempt to connect or short any of the voltage outputs together in an effort to gain more power output.
Page 4 No Accidental Startups will occur with the Z-4000 because the variable outputs are protected from accidental high-power startup. If the throttle handles are not in the OFF position when the Z-4000 is first turned on, no power will be applied to the track and the red OVERLOAD light will illuminate.
Page 5 There is no Program Button operation in Proto-Sound 2.0. Please see your engine’s operating instructions for the combination signals to operate its features. Z-4000 Transformer Operating Manual...
Page 6 4. The locomotive will make air release sounds to indicate what feature number you have selected (i.e. if you chose feature number six, the air release will sound six times in rapid succession). This will be followed by a series of Z-4000 Transformer Operating Manual...
Page 7 You will know you have successfully exited PROGRAM when the amps display no longer shows “PG.” 8. When Power is turned back on the Engine will be in RESET. Z-4000 Transformer Operating Manual...
Page 8 The track voltage will increase for as long as the Bell button is depressed (up to about 25 seconds) and the Z-4000’s maximum output voltage has not been exceeded. 3. When you release the Bell button, the track voltage will gradually decrease to the commanded level set with the throttle.
Page 9 3. Firmly press and release the Bell button to start the Lock-Out Macro. At this point, the Z-4000 will blow the locomotive horn or whistle while reducing the track voltage to 0.0. Within two seconds of the track voltage dropping, your locomotive will sound a short blast of its whistle or horn and track power will be restored.
Page 10 3. Firmly press and release the Bell button to start the Unlock Macro. At this point, the Z-4000 will blow the locomotive horn or whistle while reducing the track voltage to 0.0. Within three seconds of the track voltage dropping, your locomotive will sound a ding of its bell and track power will be restored.
Page 11 Neutral causes the Bell to ring. All the wires are properly attached Check that all the circuit breakers but no power outputs from either are closed and that the Power Track 1, Track 2 or the Auxiliary Switch is ON. outputs. Z-4000 Transformer Operating Manual...
Page 12 In the event such conditions exist, the transformer should not be used until properly repaired. This Z-4000 is intended for indoor use. Do not use if water is present. Serious injury or fatality may result.
Page 13 Any changes or modifications not expressly approved by M.T.H. ElectricTrains could void the user’s authority to operate this equipment in the USA. Z-4000 Transformer Operating Manual...
Page 14 Service & Warranty Information How to Get Service Under the Terms of the Limited One-Year Warranty For warranty repair, do not return your product to the place of purchase. Instead follow the instructions below to obtain warranty service as our dealer network is not prepared to service the product under the terms of this warranty.