Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Zenesis ZN-302 A
Summary of Contents for Zenesis ZN-302 A
- Page 1 ZN-302 A/S/AS USER MANUAL...
- Page 2 Thank you for purchasing our product. Our systems have all been designed and tested to be compatible with the earliest to latest vehicles available throughout the world. Our primary goal was to provide a reliable and stable product. Our secondary goal was to ensure that our systems are easy to install.
- Page 3 3. If any defects are discovered, do not open or attempt to re- pair the system. Ask the installer for assistance. 4. Zenesis Alarms will not be responsible for any theft and/or damages to your vehicle. 5. The installer of this system will be responsible for any injuries and/or damages resulting from incorrect installation.
-
Page 4: Table Of Contents
CONTENTS 1. Introduction System Contents Remote Control Button Layout Remote Control Battery Replacement Remote Control Button Introduction (Primary/Secondary) 2. Primary Features Door Lock (Arm) (302 A/AS) Door Unlock (Disarm) (302 A/AS) Arm / Disarm Status (302 A/AS) Vehicle Status Panic (302 A/AS Only) Remote Start Trunk Release Valet Mode... -
Page 5: Introduction
1. INTRODUCTION 1.1 System Contents 1.2 Remote Control Button Layout 1.3 Remote Control Battery Replacement 1.4 Remote Control Button Introduction... -
Page 6: System Contents
System Contents Main Control Module Remote Control x 2 Antenna Module 1 x 2-way & 1 x 1-way Shock Sensor (A/AS) Manuals Siren (A/AS) Wiring Harnesses... -
Page 7: Remote Control Button Layout
Remote Control Button Layout Antenna Function Door Lock / Arm Door Unlock / Disarm Remote Start Trunk Release 1-way Remote Control Specifications Radiation ± 20 ppm / year Temperature - 40°C ~ +80°C... -
Page 8: Remote Control Battery Replacement
Remote Control Battery Replacement Slide out the battery tray. Replace with CR2032 3V battery. Caution: Ensure that the polarity of the battery is correct. The positive (+) termi- nal should be facing you. Remote Control Button Layout Primary Features Button Sequence Button Feature Description Sequence... -
Page 9: Remote Control Button Introduction (Primary/Secondary)
Secondary Features Button Sequence Button Sequence Feature Description Description Hold Function Button 2 sec Siren Mute ON/OFF (302 A/ → Press and release Lock Button Hold Function Button for 2 Remote Control Beep Mute sec → Press and release ON/OFF Unlock Button Hold Function Button for 2 Valet Mode ON/OFF sec → Press and release Remote Start Button Hold Function Button for 2 Paging ON/OFF (302 A/AS) sec → Press and release Trunk Button Press and release Function Aux 1 Button → Press and ... - Page 10 Button Sequence Button Sequence Feature Description Description Passive Arm ON/ Hold Brake Pedal → Press and release Function Button three times → Press and release Lock Button Shock Sensor ON/ Hold Brake Pedal → Press and release Function Button three times → Press and release Unlock Button Ignition Lock ON/ Hold Brake Pedal → Press and release Function Button three times → Press and release Remote Start Button Safety Rearm Hold Brake Pedal → Press and release Function Button four times → Press and release Lock Button Turbo Timer ON / Hold Brake Pedal → Press ...
- Page 11 Legend: : Press and hold button for 2 seconds. → : Press buttons in sequence one after the other. : Function Button For example, means to press and release (Function Button) 2 times and then press and release once.
-
Page 12: Primary Features
2. PRIMARY FEATURES Door Lock (Arm—302AS) Door Unlock (Disarm—302AS) Arm / Disarm Status (302AS) Vehicle Status Panic (302AS) Remote Start Trunk Release Valet Mode Remote Control Button Hold... -
Page 13: Door Lock (Arm) (302 A/As)
Door Lock (Arm) (302 A/AS) Press and release Normal Conditions: 1 parking light flash & 1 1 BLUE LED flash & 1 Vehicle Remote Control siren chirp beep Open door: 3 parking light flash & 3 3 RED LED flashes & 3 Vehicle Remote Control siren chirp... -
Page 14: Door Unlock (Disarm) (302 A/As)
Door Unlock (Disarm) (302A/AS) Press and release Normal Conditions 2 parking light flashes & 2 BLUE LED flashes & Vehicle Remote Control 2 siren chirps 2 beeps Unlock with warning trigger 3 parking light flashes & 3 RED LED flashes & 3 Vehicle Remote Control 3 siren chirps... -
Page 15: Vehicle Status
2.4 Vehicle Status Press and release The status of the vehicle will be displayed on the 2-way remote control. The fol- lowing table describes the different situations. Please note the priority (top to bottom). If a status condition is met, any other conditions below it will not be checked. -
Page 16: Trunk Release
Failed remote start: Reason for Failure Vehicle Remote Control Failed Remote Start 4 parking light flashes & 4 4 RED LED flashes & 4 siren chirps beeps Key in key cylinder at ON 5 parking light flashes & 5 5 RED LED flashes & 5 position siren chirps beeps... -
Page 17: Remote Control Button Hold
• Valet mode ON will turn off the remote start feature on 302S and 302AS models. Valet mode ON 1 parking light flash & 1 1 BLUE LED flash & 1 Vehicle Remote Control siren chirp beep Valet mode OFF 2 parking light flash &... -
Page 18: Secondary Features
3.SECONDARY FEATURES Programming Guide User Programmable Options Remote Control Registration Remote Start Reservation Temperature Status Paging (302 A/AS) Remote Control Beep Mute Siren Mute (302 A/AS) Passive Lock (Arm—302 A/AS) 3.10 Safety Relock (Rearm—302 A/AS) 3.11 Ignition Lock 3.12 Cold Start Timer 3.13 Turbo Timer 3.14 Convenience Run 3.15 Aux Outputs... -
Page 19: Programming Guide
3.1 Programming Guide In order to do any programming, you must first enter into the Programming Op- tions. Once in programming mode, keep in mind, you have 10 seconds to press any button sequence(s) otherwise the system will automatically exit you out of the programming mode. -
Page 20: User Programmable Options
3.2 User Programmable Options ENTER INTO PROGRAMMING OPTION FIRST: Press and release 3 times. Press and release . You will see 5 Blue LED flashes on the Remote Control. You will also hear 5 beeps from the 2‐way Remote Control. You are now in User Programmable Mode. THEN FOLLOW THE CHART BELOW FOR PROGRAMMING OPTIONS: * Once you enter into User Programmable Options, you will have 10 sec- onds to enter a button press before it automatically exits. Options Button Feature Combination Diesel warm 30 sec 15 sec 7.5 sec... - Page 21 For example, if siren sound time needs to be changed to 100 seconds, the follow- ing procedure would be used. Press and release 3 times and press and release You will see 5 Blue LED flashes on the Remote Control. You will also hear 5 beeps from the 2-way Remote Control.
-
Page 22: Remote Control Registration
Remote Control Registration 1. Insert the key into the key cylinder and turn to the ON position (engine is OFF). 2. Press brake pedal 4 times. On the 4 time, hold down the brake pedal. 3. 3 parking light flashes and 3 siren chirps will confirm remote control program- ming mode. -
Page 23: Temperature Status
3.5 Temperature Status Press and hold for 2 sec The interior temperature of the vehicle will be displayed as a series of LED flashes and beeps on the remote control. Temperature Remote Control LED Less than or equal to -10°C (14°F) 2 BLUE LED flash &... -
Page 24: Remote Control Beep Mute
3.7 Remote Control Beep Mute (Press and hold Function Button for 2 seconds and then press and release Unlock Button) Remote control beep mute ON - Beeper OFF Remote Control 1 BLUE LED flash & 1 beep All features of the system still function with remote control beep mute ON. Remote control beep mute OFF - Beeper ON Remote Control 2 BLUE LED flashes &... -
Page 25: Safety Relock (Rearm) (302 A/As)
Passive lock (arm) OFF 2 parking light flash & 2 2 BLUE LED flashes & Vehicle Remote Control siren chirps 2 beeps CAUTION: If passive lock (arm) is ON, always carry the remote control and keys as there may be cases of getting the keys locked inside the car accidently. Alter- natively, installing ZPASS TOUCH system will prevent accidental key lockouts. -
Page 26: Cold Start Timer
3.12 Cold/Hot Start Timer A timer can be set to remote start the car. Once activated, the vehicle will remote start automatically. The timer can be set to start every 1,2, 4, or 6 hours. How- ever, a temperature constraint can also be added so that if the temperature reaches a certain level, the timer will start. - Page 27 Timer Setting The timer setting will either turn ON or OFF the Cold/Hot Timer. Selecting a time to start the remote starter will turn ON Cold/Hot Timer. Cold or Hot Start Main Setting The Cold/Hot Timer can be set to start according to timer and/or tempera- ture constraints.
-
Page 28: Turbo Timer
The engine will continue to idle after the key is turned to the OFF position. Zenesis Electronics developed patent-pending ZMATIC Intelligent Turbo Timer that allows users to select 4 different settings for Turbo Timer. - Page 29 (emergency brake) is engaged. Do not idle the vehicle in an enclosed area. Do not idle the vehicle if any laws prohibit this action. Zenesis’ Super Intelligent Turbo Timer uses complex algorithms to calculate the optimal engine run time to properly cool down the turbo or supercharger. Due to the complexity of this technology, the system may not work on some select vehicles.
-
Page 30: Convenience Run
3.14 Convenience Run (Hold Brake Pedal down. Press and hold Remote Start Button for 2 seconds) This feature will allow the engine to run even though the key has been removed from the key cylinder. The engine will run for the amount of time that is set in Remote Start Run Time. -
Page 31: Shock Sensor (302 A/As)
you have a convertible, you can HOLD DOWN the corresponding AUX OUTPUT button sequence and stop at a desired time. If you want your convertible roof to stop at halfway, you can do so through this. LATCH: once activated will run the AUX OUTPUT. You must press the corre- sponding button sequence to deactivate the AUX OUTPUT function. -
Page 32: Shock Sensor On/Off (302 A/As)
This feature allows the user to control a second vehicle that has a compatible Zenesis car security / remote starter product installed. You can do this by press- ing and releasing the Function Button 5 times and then pressing and releasing the Lock Button. -
Page 33: Warranty Card
press “SHIFT”. d. Once all of the numbers are entered, press ENTER until all LED’s blink 3 times. 2. System Arm/Disarm a. Press ENTER until LED # 1,2,3,4,5 light up. b. Enter 4 - 10 digit PIN. c. Press ENTER until the system arms or disarms. 3. - Page 34 NOTES:...
- Page 35 NOTES:...
Need help?
Do you have a question about the ZN-302 A and is the answer not in the manual?
Questions and answers