Page 1
COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE...
TX-SR501/E Specifications AMPLIFIER SECTION TUNER SECTION Continuous Average Power output (FTC) All channels: 65 watts per channel min. RMS at Tuning Range 8 Ω, 2 channels driven from 20 Hz North American models: 87.50-108.00 MHz (100 kHz steps) Other models: 87.50-108.00 MHz (50 kHz steps)
TX-SR501/E SERVICE PROCEDURES 1. Replacing the fuses 4.Setting the voltage selector (Worldwide models only) This symbol located near the fuses indicates that the fuse used is fast operating type. For continued protection against Worldwide models are equipped with a voltage selector to conform fire hazard, replace with same type fuse.
(Remote Interactive) connector can be connected to COMPONENT VIDEO (10, 12, 14, 16) connector on another Onkyo AV component, for These RCA/phono connectors can be used to connect a TV, example, a CD player, DVD player, or cassette recorder. The DVD player, or other AV component with component video TX-SR501/TX-SR501E’s remote controller can then be used...
TX-SR501/E Front Panel North American Model 3 4 5 MASTER VOLUME STANDBY/ON DIRECT STEREO SURROUND PRESET/ADJUST STANDBY SUBWOOFER SPEAKERS DISPLAY DIMMER DIGITAL INPUT MODE MEMORY FM MODE TUNING SPEAKER ADJUST AUDIO ADJUST CLEAR PHONES VIDEO INPUT AUDIO VIDEO 1 VIDEO 2...
Page 6
TX-SR501/E Controls & Connectors—Continued MEMORY button (30, 31) PHONES jack (33) This button is used when storing and deleting radio presets. This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening. FM MODE button (31)
TX-SR501/E Supplied Accessories Make sure you have the following accessories: Only supplied in certain countries. Use this adapter if your AC outlet does not match with the plug on the TX-SR501/ Indoor FM antenna TX-SR501E’s power cord. (Adapter var- (connector type varies from ies from country to country.)
Page 8
TX-SR501/E Controls & Connectors—Continued This page describes only those buttons that can be used to Remote Controller—RCVR Mode control the TX-SR501/TX-SR501E when the remote con- troller is in RCVR mode (Receiver mode). RC-518M (North American model) To select RCVR mode, press the [RCVR] button.
TX-SR501/E BLOCK DIAGRAM Main microprocessor FM/AM BD3811K1 TUNER DECODER PACK BU1923F VIDEO3 European model only INPUT GAIN 0/6dB INPUT GAIN TAPE OUT 0/6dB INPUT GAIN TAPE IN 0/6dB INPUT GAIN VIDEO-3 0/6dB VIDEO-2 IN INPUT GAIN 0/6dB VIDEO-1 OUT INPUT GAIN...
Page 11
TX-SR501/E BLOCK DIAGRAM Power Amplifier MASTER VOLUME 0~-103dB HEADPHONE OUTPUT GAIN BASSBOOST BASS/TREBLE +27dB 0~18dB OPAMP OUTPUT GAIN +27dB BASS/TREBLE 0~18dB OPAMP SPBL SPBR OUTPUT GAIN +27dB 0~18dB OPAMP OUTPUT GAIN +27dB 0~18dB OPAMP OUTPUT GAIN +27dB 0~18dB OPAMP OUTPUT GAIN...
TX-SR501/E IC BLOCK DIAGRAMS AND DESCRIPTIONS BU1923F(RDS Decoder) BLOCK DIAGRAM VSS3 8ch Switched capacitor filter Comparator anti-aliasing VREF filter (16) RCLK VDD1 Analog Power supply QUAL VSS1 RDATA Differential Bi-phase 57kHz (12) 1187.5Hz decoder decoder RDS/ARI VDD2 Digital power supply...
Page 38
TX-SR501/E IC BLOCK DIAGRAMS AND DESCRIPTIONS BD3812F(Audio Sound Processor) OUT1 1ch input 1ch output AGND1 OUT2 Analog ground 2ch output 2ch input Serial data select AGND2 DGND Analog ground Comparator ground MUTE (-)Power supply Mute AGND3 LOGIC Analog ground Serial data...
Page 39
TX-SR501/E IC BLOCK DIAGRAMS AND DESCRIPTIONS BD3811K1(6ch Volume with 8ch input selector) No. Terminal Description INDSPSL DSP surround Lch input terminal INDSPC DSP center input terminal INDSPSW DSP sub woofer input terminal I N 3 1 T N F 2...
Page 40
TX-SR501E IC BLOCK GIAGRAMS AND DESCRIPTIONS AK4586VQ(96kHz 6ch CODEC) No. Name Description Crystal oscillator output pin Crystal oscillator input pin EXTCLK Master clock input pin XTI/EXTCLK TVDD Power supply pin for output buffer. 2.7V to 5.5V DVSS Digital ground pin DVDD ROUT1 DVDD...
Page 41
TX-SR501/E IC BLOCK DIAGRAMS AND DESCRIPTIONS TC74VHC541FT(Octal bus buffer) TC7HTC7007AF(Hex buffer) INPUTS OUTPUT X :Don't care Z :High impedance 74HCU04F(Hex Inverter) TC7WU04FU(Triple inverter) Truth table (TOP VIEW) TC74VHC574FT(Octal D-FF with 3-state output) INPUTS OUTPUT CK Q CK Q CK Q...
Page 42
TX-SR501/E RL241,2 MAIN MICROPROCESSOR-CONNECTION DIAGRAM RL901 Q241 Q921 COMPONENT VIDEO POWER Q7006,Q205 Q201,Q207,Q208 VIDEO 2 VIDEO 1 RELAY RELAY SW MUTE DRIVE MUTE SW CIRCUIT Q7007,Q206 Q202,Q210,Q211 RL6600 VIDEO 1 VIDEO 2 MUTE DRIVE MUTE SW RL6603, CIRCUIT Q6601 RL6604...
Page 44
TX-SR501/E TERMINAL DESCRIPTION MAIN MICROPROCESSOR No. Terminal I/O Description PROTECT Protection circuit detection input terminal VOLH Power amplifier voltage detection terminal. BAND Region setting input terminal. 11 232TXD Not used. 15 MCRDY Data ready detection input terminal from the sub microprocessor.
Page 45
TX-SR501/E TERMINAL DESCRIPTION SUB MICROPROCESSOR Pin No. Symbol I/O Description Pin No. Symbol I/O Description Power supply terminal. Connect to 5V. Segment output terminal of P22. Ground terminal. Segment output terminal of P21. Ceramic oscillator connection terminals for main system.
TX-SR501/E ADJUSTMENT AND CONFIRMATION PROCEDURES 1 Idling current adjustment Before Idling adjustment, turn the trimming resistors R6040,R6041,R6042,R6043 and R6044 to counter clockwise. Connect the DC voltmeter to sockets P6080,P6081,P6082,P6083,P6084 and P6085. After turn POWER to ON, adjust the trimming resistors R6040,R6041 and R6042 so that the reading of voltmeter becomes 2.5 mV.
TX-SR501/E ADJUSTMENT AND CONFIRMATION PROCEDURES 2 3. Confirmation of Current detection circuit Set the unit to "TEST-1-00". Connect the differentiating circuit and apply the 200Hz square signal to DVD INPUT terminal of each channel. Adjust the attenuator or Volume so that the output level becomes 35V p-p.
TX-SR501/E PACKING PROCEDURES Bottom Except 120V model Accessary bag (120V models) Put the label 81 between page 2 and page 3 of instruction manual E. Speaker Cable (Canadian model only) Accessary bag (Other models) Printed matters (Other models) Put the label 81 between page 2 and page 3 of instruction manual E.
Page 53
DESCRIPTION CIRCUIT NO. PART NO. Terminal P241 25045731 NPJ-9PDGLR519 Sockets P242A 25052216 NSCT-20P2113 P243B 25051526 NSCT-4P1313 Constant voltage circuit PC board (NAETC-7833-1A/1B) DESCRIPTION CIRCUIT NO. PART NO. Q6931 222780565JRC 78M56(NJM78M56FA) Diodes D6932,D6933 22380260 or RL1N4003 or D6932 or 22380035 GP104003E Capacitors C6931 394651027 or...
Page 54
Power amplifier PC board (NAAF-7842-1A/1B/1C/1D/1E/1F) DESCRIPTION CIRCUIT NO. PART NO. Transistors Q6010~Q6015 2213284 or 2SC1740S-R or 2213285 2SC1740S-S Q6020~Q6025 2213284 or 2SC1740S-R or 2213285 2SC1740S-S Q6030~Q6035 2203434 or KTD2061-Y or 2203010 2SC5171 Q6040~Q6045 2203424 or KTB1369-Y or 2203000 2SA1930 Q6070~Q6075 2215896, KTC3200-BL, 2210755,...
Need help?
Do you have a question about the TX-SR501/E and is the answer not in the manual?
Questions and answers