Patton PX306 Owner's Manual page 2

P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions 12. Do not let the cord hang over the edge of a table,
should always be taken including the following: counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
1. Read all instructions before using this appliance.
13. Do not use outdoors.
2. Use fan only for purposes described in the instruction
14. To disconnect, grip plug and pull from wall outlet.
manual.
Never yank on cord.
3. To protect against electrical shock do not immerse
15. Always use on a dry, level surface.
unit, plug or cord in water or spray with liquids and
16. Do not operate fan until fully assembled with all
plug the appliance directly into a 120V AC electrical
parts properly in place.
outlet.
17. This product is intended for household use ONLY and
4. Close supervision is necessary when any appliance is
not for commercial or industrial applications.
used by or near children.
18. WARNING: To reduce the risk of electrical shock
5. Unplug from outlet when not in use, when moving
and injury to persons, do not use in window.
fan from one location to another, before putting on
19. WARNING: To reduce the risk of fire or electric
or taking off parts and before cleaning.
shock, do not use this fan with any solid-state speed
6. Avoid contact with moving parts.
control device.
7. Do not operate in the presence of explosive and/or
20. This product employs overload protection (fuse). A
flammable fumes.
blown fuse indicates an overload or short-circuit
8. To avoid fire hazard, NEVER place the cord under
situation. If the fuse blows, unplug the product from
rugs or any parts near an open flame, cooking or
the outlet. Replace the fuse as per the user servicing
other heating appliance.
instructions (follow product marking for proper fuse
9. Do not operate any appliance with a damaged cord
rating) and check the product. If the replacement
or plug after the appliance malfunctions, or has been
fuse blows, a short circuit may be present and the
dropped/damaged in any manner. Discard fan or
product should be discarded or returned to an
return to an authorized service facility for
authorized service facility for examination and/or
examination and/or repair.
repair.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
PLEASE READ AND SAVE
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
THESE IMPORTANT
tripped over.
SAFETY INSTRUCTIONS
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
THIS APPLIANCE HAS A POLARIzED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
PX306_11EM1.indd 2
F E AT U R E S - O P E R AT I O N S
ASSEMbLY INSTRUCTIONS 3. To adjust the fan speed, turn the speed control knob
to the desired setting (0-Off, III-High, II-Medium,
Carefully unpack contents from carton.
I-Low).
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
Figure 2
PARTS THAT COULD BE REQUIRED TO ASSEMBLE YOUR FAN.
ASSEMbLY
Refer to diagrams below (Figure 1 & 2) for visual aid.
1. Place left and right Leg Assemblies (labeled with L and
R) over each corresponding side. Secure with Tilt
Control Knobs by turning in a clockwise direction.
2. Insert Base Tubing into Leg Assemblies and secure
with Base Screws, Washers, and Nuts.
OPERATING INSTRUCTIONS
1. Set fan on a dry, level surface.
2. Plug cord into any standard 120 volt AC outlet.
Spring Washer
Please make sure the speed control is in the off
position.
Figure 1
Speed Control Knob
Left Leg Assembly
Nut (2)
Rubber Feet (2)
PX300 HV fan 10/03
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
ADJUSTMENT INSTRUCTIONS
Fan Head Tilt-Adjustment:
1. To change the tilting angle of the fan head, simply
loosen the Tilt-Adjustment Knobs.
Base Screw
2. Move the fan head to the desired angle and firmly
tighten the Tilt-Adjustment Knob to lock into place.
Flat Washer
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your fan. Please remember:
REPLACEAbLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please
order a new fuse at 1-800-333-1930. Follow the below
instructions to replace the fuse on the plug.
User Servicing Instructions
Nut
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide
the cover down towards the prongs.
Housing
Note: Ensure that fuse cover is completely open
before attempting to remove fuse.
3. Remove fuse carefully by
Right Leg Assembly
using a small screwdriver to
pry the fuse out of the
Tilt Control Knob (2)
compartment by the metal
ends of the fuse (see Figure
3).
4. Place plug on a solid, flat
surface. Insert new 5 Amp,
125 Volt fuse into fuse
Base Screw (2)
compartment and use a small screwdriver to secure
the metal ends of the fuse into the compartment.
Flat Washer (2)
Caution: Risk of fire. Replace fuse only with 5 Amp,
Spring Washer (2) 125 Volt fuse.
Base Tubing
5. Slide fuse cover closed completely. If fuse cover is
difficult to close, make sure fuse is secured in place
completely by pressing down on metal ends of the
fuse.
6. Risk of fire. Do not replace attachment plug. Contains
a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
FAN CLEANING:
• Always unplug the fan before cleaning or
disassembling.
• Do not allow water to drip on or enter into fan housing.
• Be sure to use a soft cloth moistened with a mild soap
solution.
• Do not use any of the following as a cleaner: gasoline,
thinner, or benzene.
Clean the fan blade, grill, housing and base with a soft,
damp cloth. Please use caution around the motor housing
area. Do not allow the motor or other electrical
components to be exposed to water.
FAN STORAGE
When storing your fan in the off season, it is important to
keep it in a safe dry location. It is important to protect
the fan head from dust. We strongly recommend using
the original box from purchase.
Figure 3
If you have any questions regarding your product or
Fuse
Fuse cover would like to learn more about other Patton ®
products, please contact our Consumer Service
Department at 1-800-333-1930 or visit our website
at www.pattonproducts.com.
Metal ends
7/14/11 5:11 PM