Jura IMPRESSA S9 Instructions For Use Manual
Jura operating manual coffeemaker impressa s9,s7
Hide thumbs
Also See for IMPRESSA S9:
- Instructions for use manual (22 pages) ,
- Short operating instructions (4 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Jura IMPRESSA S9
Summary of Contents for Jura IMPRESSA S9
- Page 1 IMPRESSA S9/S7 avantgarde Instructions for use 1/06...
- Page 2 Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.com...
- Page 3 Fig. 1 Fig. 2 Fig. 5 Fig. 6 Fig. 9 Fig. 10 Fig. 13 Fig. 14 Fig. 3 Fig. 7 Fig. 11 Fig. 4 Fig. 8 Fig. 12...
- Page 4 Description of the machine 1. Drip tray 2. Drip grate 3. Programming door 4. Rotary Switch 5. Selection key for pre-ground coffee 6. Coffee à la Carte key 7. 1 Coffee key 8. 2 Coffees key 9. 1 Espresso key 10.
-
Page 5: Table Of Contents
Contents 1. Safety information ...page 6 Warnings ...page 6 Precautions...page 6 2. Before you start using the IMPRESSA S9/S7 avantgarde ...page 6 Checking the mains voltage ...page 6 Checking electrical fuse...page 6 Filling the water tank ...page 7 Filling the bean tank...page 7 Adjusting the grinding gear ...page 7... -
Page 6: Before You Begin
Before you begin Congratulations on having bought this IMPRESSA S9/S7 avant- garde! In order to ensure perfect operation of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or meet with particular prob-... -
Page 7: Filling The Water Tank
2.3 Filling the water tank Only use fresh, cold water. Never fill the water tank with milk, mineral water or other liquids. Take out the water tank and thoroughly rinse it out with cold tap water (Fig. 1). Then fill it with water and place it back into the coffee machine. Make sure the tank is installed correctly and that it engages properly. -
Page 8: Cup Illumination
Place a receptacle under the 2-stage frothing jet (24) and press one of the Steam keys The system now fills up automatically. A little water will leak from the frothing jet. SYSTEM FILLING HEATING UP PRESS RINSE Place a cup under the height-adjustable coffee spout (18). Press Rinse MACHINE RINSING Now the water lines are flushed with fresh water. -
Page 9: Using A Claris Plus Filter Cartridge
Now turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode. SELECT PRODUCT 5. Using a CLARIS plus filter cartridge When using the CLARIS plus filter cartridge correctly, de- calcifying your IMPRESSA will no longer be necessary. -
Page 10: Rinsing The Machine
Place a sufficiently large receptacle (min. 0.5 litres) under the pivoting steam spout (23) and press one of the Steam keys to start the filter rinsing process. FILTER RINSING Filter rinsing stops automatically. SELECT PRODUCT You can also trigger a change of filter manually from the Maintenance menu at any point in time (only if the filter has been activated) - see Chapter 13.3. -
Page 11: Making Coffee À La Carte
The coffee brewing process stops automatically as soon as the set amount of water has run through. SELECT PRODUCT To stop the brewing process prematurely, press any of the product keys. We recommend always using powder from fresh coffee beans or pre-ground, vacuum-packed coffee. Never fill in more than 2 scoops of powder. -
Page 12: Drawing Off Steam
You can also change the amount of water set while the machine is brewing coffee. Open the programming door. Turn the Rotary Switch (4) until the display indicates the required amount (ML). The amount of water can be selected in increments of 5 ML. The amounts given in ML are approximate values and may vary from the effective quantity. -
Page 13: Attaching The Professional-Cappuccino Frother To The Impressa
Now attach the Professional-Cappuccino Frother (Fig. 6). Press the hose into one side of the opening behind the dial (Fig. 7). IMPRESSA S9 avantgarde: The supplied “Deluxe” milk pitcher is suited for drawing in the milk. 11.4 Making cappuccino and hot milk with the... -
Page 14: Programming
MACHINE RINSING The coffee spout (18) is rinsed. 13. Programming The IMPRESSA leaves the factory with a number of default settings that allow you to make coffee without having to pro- gram the machine first. You can, however, adjust various parameters to make the coffee suit your personal taste. -
Page 15: Setting The Amount Of Water For Coffee
SELECT PRODUCT Open the programming door (3). Press the Rotary Switch (4) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (4) until the following message is dis- played: POWDER QUANTITY Now press the Rotary Switch (4) to start programming. SELECT PRODUCT Then press a product key of your choice. -
Page 16: Programming The Temperature For Coffee, Espresso And Coffee À La Carte
13.6 Programming the temperature for coffee, espresso and coffee à la carte You can adjust the temperature for each type of coffee sepa- rately. The temperature can be set to 2 different levels (NORMAL, HIGH). SELECT PRODUCT Open the programming door (3). Press the Rotary Switch (4) until you hear an acoustic signal. -
Page 17: Economy Mode
FILTER NO or YES Turn the Rotary Switch (4) until the following message is dis- played: STEAM PORTION Press the Rotary Switch (4) to activate the program item. PORTION 20 SEC (example) Turn the Rotary Switch (4) to modify the steam portion and then confirm your setting by pressing the Rotary Switch (4). -
Page 18: Setting The Time
Select this setting if you make mostly black coffees and are prepared to wait for approx. 1 minute before being able to draw steam. Economy mode 2 Selecting this level does not put the IMPRESSA in stand-by mode (economy temperature). The machine heats up each time you make coffee or need to draw steam. -
Page 19: Programming The Automatic Switch-Off Time
Now press the Rotary Switch (4) to start programming. UNIT ON —:— Turn the Rotary Switch (4) to set the hours. UNIT ON 07:00 (example) Press the Rotary Switch (4) to confirm the hours and to activate the minutes. UNIT ON 07:00 Turn the Rotary Switch (4) to set the minutes. -
Page 20: Programming The Display
SPRACHE DEUTSCH Turn the Rotary Switch (4) to set the language. LANGUAGE ENGLISH (example) Confirm your selection by pressing the Rotary Switch (4). LANGUAGE ENGLISH Now turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode. SELECT PRODUCT 13.14 Programming the display This program item allows you to change the time format... -
Page 21: Resetting Products To Factory Settings
Now press the Rotary Switch (4) to access the Information menu. TOTAL 1000 (example) Turn the Rotary Switch (4) to display how often you made 2 espressos, 1 coffee, 2 coffees, coffee à la carte, powder, water and steam. Finally, the number of cleaning and decalcifying cycles and filter changes are displayed. -
Page 22: Emptying The Drip Tray
14.3 Emptying the drip tray EMPTY TRAY If this information is displayed, the machine will no longer dispense coffee or steam, and the tray must be emptied. Carefully take out the drip tray (1) – which contains water – and the integrated coffee grounds bin. -
Page 23: Prompt To Run Decalcifying Cycle
After another 30 products the display will change. You should run the cleaning cycle now (see Chapter 15). SELECT PRODUCT / CLEAN NOW 14.9 Prompt to decalcify Lime scale builds up in the IMPRESSA as a result of normal use. The degree of calcification depends on the hardness of the water you use. -
Page 24: Decalcifying
Once started, the cleaning process must not be interrupted. After each cleaning process, the filler funnel for the pre- ground coffee (17) should be cleaned as well. SELECT PRODUCT CLEAN MACHINE Press Rinse until the following message appears: EMPTY TRAY / EMPTY GROUNDS Empty out the drip tray (1) and integrated coffee grounds bin. - Page 25 Once started, the decalcifying program must not be inter- rupted. Always wait until the decalcifying agent has been used up and the tank is empty. Never fill in additional decalcifying agent. SELECT PRODUCT DE-SCALE MACHINE Press Rinse until the following message appears: EMPTY TRAY / EMPTY GROUNDS Empty out the drip tray (1) and integrated coffee grounds bin.
-
Page 26: Disposal
MACHINE DE-SCALING You will hear an acoustic signal. CLOSE TAP Turn the Hot Water key (22) to the symbol. MACHINE DE-SCALING You will hear an acoustic signal. EMPTY TRAY / EMPTY GROUNDS Empty out the drip tray (1) and integrated coffee grounds bin. TRAY MISSING Place the empty, clean drip tray (1) and integrated coffee... -
Page 27: Problems
19. Problems Problem Grinding gear makes a very loud noise Too little froth when frothing milk Coffee only drips from the coffee spout Display constantly indicates ‘Tray missing‘ ‘Fill beans’ not displayed despite empty bean tank Cause Foreign body in the grinding gear Professional Cappuccino Frother clogged Grinding degree too fine Pre-ground coffee too fine... -
Page 28: Legal Information
20. Legal information These operating instructions contain all the information required for operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during mainte- nance.
Need help?
Do you have a question about the IMPRESSA S9 and is the answer not in the manual?
Questions and answers