Transmitter Overview Transmitter part number: 1411-03 Call your dealer or visit www.caralarm.com to order “lock” replacement transmitters. button Battery replacement: “unlock” Remove the small screw from the button lower back case, and separate the “start” transmitter halves� Replace the button CR2032 battery (or with 2 CR2016 batteries) and reassemble the “trunk”...
Page 4
Transmitter Functions (cont’d) TRUNK RELEASE / ChANNEL 2: Press the “TRUNK” button for 3 seconds� • THE SYSTEM WILL DISARM / UNLOCK AND THE TRUNK WILL OPEN (IF EQUIPPED)� REmOTE START: Press and release the “START” button twice within 5 seconds� (see user feature #8 for additional options) •...
Page 5
Transmitter Functions (cont’d) SILENT LOCK / UNLOCK: Press and release the “TRUNK” button twice in 5 seconds� • THE PARKING LIGHTS WILL FLASH, AND THE SYSTEM WILL LOCK/ARM OR UNLOCK/DISARM DEPENDING ON THE CURRENT SYSTEM STATE� REmOTE VALET: Press “LOCK” then “UNLOCK” then “TRUNK” + “START”...
Transmitter Functions (cont’d) AUXILIARY FUNCTIONS 1-4: The actual operation of these functions will vary from car to car� They are designed to operate extra functions like automatic sliding doors or motorized hatches� Aux 1-4 are virtual outputs only available when this system is integrated with the vehicle’s data network� Consult with your installer to find out if any of these functions are available, then confirm each operation and write them below�...
Other Remote Start Features (cont’d) mANUAL TRANSmISSION STARTING Remote starting with a manual transmission requires a different installation method and installer feature #11 must be turned on� Also, a setup procedure that ensures the transmission was left in neutral must be performed each time you leave your vehicle and intend to use remote start later�...
Security System Features (cont’d) whEN ThE SYSTEm TRIGGERS If the system were to be compromised while armed, it will trigger sounding the siren/horn and flashing the parking lights for 30 seconds (programmable). When disarming the system after a trigger event, the siren/horn will chirp 4 times and the parking lights will flash 4 times instead of the standard 2 times.
The Status Light The status lights, located in the window-mount antenna, provide a visual indication of the system’s status� SECURITY SYSTEm STATUS OFF: The alarm is disarmed and not performing any automatic functions� ON: The alarm is in valet mode� FLAShING SLOw: The alarm is armed and monitoring all entry points�...
Anti-Carjacking Protection The system is equipped with two separate Anti-Carjacking protection features (ignition, open door, or both) that are selectable via user feature #12� Once activated, the user has 53 seconds to cancel the Anti-Carjacking protection process (described below)� If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren will begin to chirp for 7 seconds to alert the user that the system is about to enter into an alarm condition�...
Programming Transmitters Standard Programming: This method to program additional or replacement trans- mitters does not affect the Unauthorized Transmitter Alert (UTA) feature� Before you begin, have all transmitters which are to operate the system at hand� Step 1 Then, turn the ignition “on” (do not crank the engine)� Step 2 Within 5 seconds of Step 1, press the Valet Switch 5 times�...
User Programmable Features Feature #1 - Remote Start Run Time 10 minutes (press “lock” button to program) - DEFAULT 5 minutes (press “unlock” button to program) 15 minutes (press “trunk” button to program) 20 minutes (press “start” to program) This sets the maximum amount of time that the remote start will keep the engine running if it is not shut down by other methods�...
Page 13
User Programmable Features (cont’d) Feature #7 - Unlock w/ Trunk Release (press “lock” button to program) - DEFAULT (press “unlock” button to program) “2nd channel” is most commonly used for trunk release, in which case the alarm should also disarm. This feature, when on, configures the system to unlock/disarm when the 2nd channel is activated�...
Installer Programmable Features This group of Installer Programmable Features are all accessed as a group in the second level of features’ programming� These features have a direct affect upon the system’s operations related to the installation and vehicle type AND ShOULD ONLY BE ChANGED BY ThE INSTALLER!!! Feature #1 - Remote Start Activation From The whITE/BLUE wire 1 pulse (press “lock”...
Page 16
Installer Programmable Features (cont’d) Feature #5 - Satellite Port, Green wire Function Dome Light Output (press “lock” button to program) Start (press “unlock” button to program) - DEFAULT Ignition Output (press “trunk” button to program) Accessory Output (press “start” button to program) Status / GwR (press “lock”...
Page 17
Installer Programmable Features (cont’d) Feature #11 - manual Transmission mode (press “lock” button to program) (press “unlock” button to program) - DEFAULT This feature changes the parameters of the system’s remote start operation to be suitable for manual transmission-equipped vehicles via a “setup” procedure which must be followed upon exit- ing the vehicle to ensure the transmission is in neutral�...
Programmable Features matrix User Feature Programming: Ignition on, off, press valet 5 times Lock Button Unlock button Trunk button Start button Lock + Unlock # Feature (Brake x 1) (Brake x 2) (Brake x 3) (Brake x 4) (Brake x 5) 1 Remote Start Run Time 10 min 5 min...
Page 20
Back Cover Color cover is in a separate file.
Need help?
Do you have a question about the RS-360-EDP and is the answer not in the manual?
Questions and answers