Locking Features; Spa Control Panel (Sprint & Dash Models) - Hot Spot Tempo TEM Owner's Manual

activation during quiet evening hours.
Important: Power-up of the spa starts the F1 sequence. In order for the sleep mode to work in the evening hours, the spa must be powered up in
the early morning hours. The Sleep Mode will always be active the 6-12 hours between the end of (F2) and the begining of (F1) depending on how
the filter cycle program is set.
Note: If temperature drops below 80º F (27º C), heater will automatically activate to prevent spa from freezing.
To activate Sleep Mode feature, press and hold Temp Up () & Temp Down () buttons together for 3 seconds. This will activate the feature and
override the normal temperature demand. When these buttons have been engaged, a moon & stars icon (Sleep Icon) will apear in the display of the
control panel, indicating this feature has been activated. To deactivate this feature, simply press and hold Temp Up () & Temp Down () buttons
together for 3 seconds once again.

lOCkING FEATURES

The locking features, TEMPERATURE LOCK and SPA LOCK, are enabled from the control panel by a specific combination of buttons. Once
enabled, a lock will remain active until the specific button combination is applied to disable the lock. Even if power is disconnected from the spa and
soon thereafter reapplied (such as a power outage), the lock will remain in place.
READY
READY
READY
press any other button on the control panel until the SET icon stops flashing. The SLOC is no longer displayed.
READY
READY
READY
SET
press any other button on the control panel until the SET icon stops flashing. tLOC is then displayed.
F1
F2
To deactivate the temperature lock, press SET button. When the SET icon flashes press the Temp Up () button. Do not press any other button on
the control panel until the SET icon stops flashing. The tLOC is no longer displayed.
SPA CONTROl PANEl
SET
READY
F1
(SPRINT F2
™
MOdElS)
READY
Your control panel consists of an LED display and
convenient touch pads that allow you to set the water
temperature and adjust the skim/filter cycle settings
as well as control the hydrotherapy jets, and light from
spa-side.
lEd dISplAY
The LED display on your spa-side control panel
continually shows the spa's actual water temperature.
In certain situations, it will also display other
messages. See TROUBLESHOOTING section.
TEMpErATurE COnTrOl
The set temperature range is from 60°F (15.5°C)
to 104°F (40°C). Temperatures of any setting may
rise slightly depending on the current use and condition of your spa, and on outside temperature. Whenever power is disconnected and then
reconnected to the spa, the water temperature setting will automatically return to the default temperature of 100ºF (38ºC).
5
Pressing the Up ( ) button displays the spa's set temperature and illuminates the Up/Down LED for 3 seconds. To increase the set temperature,
Operating Instructions
SpA lOCk
SET
The spa lock feature deactivates all of the functions of the control panel. It is generally used to prevent unwanted use
F1
of the spa.
F2
To activate the spa lock, press SET button. When the SET icon flashes press the Temp Down () button. Do not press
any other button on the control panel until the SET icon stops flashing. SLOC is then displayed.
SET
To deactivate the Spa Lock, press SET button. When the SET icon flashes press Temp Down () button. Do not
F1
F2
TEMpErATurE lOCk
F1
The temperature lock feature deactivates the temperature control function from the control panel. All other functions
on the control panel will operate normally. Temperature Lock is most often used by those who do not want others to
change the set temperature of the spa water.
To activate the temperature lock, press SET button. When the SET icon flashes press the Temp Up () button. Do not
SET READY
F1
F1
F2
SET
F1
F2
& dASH
™
READY
READY
READY
READY
READY
READY
READY
Jets Button
Temperature Display
page 16
Filter Cycle LED
Light LED
Jets Pump LED
Light Button
Temperature Up Button
Heater LED
Up/Down LED
Temperature Down Button