Page 1
Cisco D9054 HDTV Encoder Installation and Operation Guide Software Version 4.2...
Page 2
Please Read This Entire Guide Veuillez lire entièrement ce guide Bitte das gesamte Handbuch durchlesen Sírvase leer completamente la presente guía Si prega di leggere completamente questa guida Important: Please read this entire guide before you install or operate this product. Give particular attention to all safety statements.
Page 3
Trademark Acknowledgements Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
• This product plugs into a socket-outlet. The socket-outlet must be near this product, and must be easily accessible. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 6
• Always pull on the plug or the connector to disconnect a cable. Never pull on the cable itself. • Do not walk on or place stress on cables or plugs. Factory service • Refer service only to service personnel who are authorized by the factory. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
• Ne marchez pas sur les câbles ou les prises et n'y exercez aucune pression. Réparations effectuées à l'usine • Ne confiez les travaux de réparations qu'au personnel autorisé par l'usine. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
• Hierzu grundsätzlich am Stecker oder Verbindungsstück und niemals am Kabel selber ziehen. • Nicht auf die Kabel oder Stecker treten oder diese einer Zugbelastung aussetzen. Hersteller-Wartung Wartungsarbeiten sind nur durch vom Hersteller autorisierte Techniker vorzunehmen. viii D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
• Tire siempre del enchufe o del conector para desconectar un cable. Nunca tire del cable mismo. • No camine ni aplique presión sobre los cables o enchufes.. Revisión y reparación de fábrica Solo personal aprobado por la fábrica puede darle servicio al producto. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
• Per scollegare un cavo tirate la spina o il connettore, non tirare mai il cavo stesso. • Non calpestare o sottoporre a sollecitazioni i cavi o le prese. Riparazionoi di fabbrica • Per le riparazioni contattate solamente personale tecnico autoizzato dalla fabbrica. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
- Take care to maintain the protective grounding of this equipment during service or repair and to re-establish the protective grounding before putting this equipment back into operation. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 12
This equipment has openings for ventilation to protect it from overheating. To ensure equipment reliability and safe operation, do not block or cover any of the ventilation openings. Install the equipment in accordance with the manufacturer's instructions. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 13
• Avoid quick stops and starts when moving the cart. • Check for uneven floor surfaces such as cracks or cables and cords. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide xiii...
Page 14
This section provides instructions for verifying that the equipment is properly grounded. Safety Plugs (USA Only) Equipment protection Class I - Cisco supplies a mains cord with a 3-terminal (grounding- type) safety plug. Do not defeat the safety purpose of the grounding-type or polarized safety plug.
Page 15
Refer all servicing to qualified service personnel only. • Moisture - Do not allow moisture to enter this equipment. • Cleaning - Use a damp cloth for cleaning. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 16
Safety Checks - After service, assemble this equipment and perform safety checks to ensure it is safe to use before putting it back into operation. Accessories Use only attachments or accessories specified by the manufacturer. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Connecting to the Contact Closure Interface ..............3-9 Connecting an External Alarm System................3-10 Connecting the Ethernet Management Interface............3-11 Connecting the IP TS Outputs..................3-12 Connecting the ASI Outputs and the ASI Monitor ............3-13 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide xvii...
Page 18
Setting Up the Statistical Multiplexing Redundancy..........5-34 Monitoring Statistical Multiplexing ................5-35 Setting Up the H.264 PIP Video Channel ..............5-39 Setting Up the H.264 PIP Video Encoding Parameters ..........5-40 Setting Up the Test Pattern ....................5-41 xviii D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 19
Setting Up the Transport Stream ................5-104 Setting Up the Service Stream ..................5-105 Setting Up the Video Program ..................5-106 Setting Up the Layer II Audio Program ..............5-107 Selecting the Dolby Digital Audio Descriptor Mode..........5-109 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 20
Setting Up the IP Network ..................5-137 Chapter 6 Service and Maintenance Section A - Firmware Upload....................6-2 Uploading Firmware to the D9054 HD Encoder using the Web Interface ....6-2 Section B - Front Panel LEDs ....................6-3 Introduction ........................6-3 Messages..........................6-4 Section C - Power Supply Replacement ................6-24 Introduction ........................6-24...
Page 21
Appendix C ISO 639-2 Language Codes Language Codes - Sorted by Alpha 3-Letter Code (ISO 639-2).........C-2 Appendix D Equipment and Accessories Accessory Kits for the D9054 HD Encoder..............D-2 Options and Upgrades ....................D-3 Appendix E Compliance Applicable Standards and Notices ................E-1 Appendix F References Applicable Documents .....................F-1...
Page 22
Contents, Continued xxii D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Encoder. Note: The manual describes all available options for the D9054 HD Encoder. Your D9054 HD Encoder may only have some of the features described in this manual. Audience The audience of this manual includes users (operators) and service personnel who are responsible for the installation, configuration, operation, monitoring and service of the D9054 HD Encoder.
4. If relevant, for synchronization, connect an external video source to REF IN. 5. Connect the external contact control equipment such as a DTMF decoder to the contact closure connector. For further information, see Connecting to the Contact Closure Interface, page 3-9. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 26
7. Connect the DATA 1 and DATA 2 connectors from the equipment after the D9054 HD Encoder to the IP TS OUT 1 and IP TS OUT 2 ports. The equipment after the D9054 HD Encoder is typically an IP set top box.
Information or Managing the System in Chapter 5. Setting Up the IP Parameters of the D9054 HD Encoder Follow the procedure below when a D9054 HD Encoder is added to or reinserted in the installation. Proceed as follows to set the IP parameters of the Management port of the D9054 HD Encoder: 1.
Page 28
Gateway parameters are validated against each other and stored. Any inconsistencies will be shown in the display. Important: For the changes to take effect you must reset the D9054 HD Encoder after you have finished setting or changing the IP address, subnet mask and default gateway.
Chapter 2 Introduction Overview Introduction This chapter is a general introduction to the D9054 HDTV Encoder. It describes the most common applications and interfaces of the encoder. In This Chapter This chapter contains the following topics. Topic See Page D9054 HD Encoder...
D9054 HD Encoder General Description The design of the D9054 HD Encoder is compact. It is a 2U encoder that fits into a 19-inch rack. It features single-channel High-Definition, high-quality SDI or composite video processing. It is targeted at uplink applications and supports ®...
Page 31
D9054 HD Encoder, Continued Audio Channels The D9054 HD Encoder is equipped with two or six stereo audio channels. The audio channels may be part of the video or stand-alone audio channels. Encoding Bit Rates Video and audio data can be encoded at the following bit rates and coding...
Page 32
Transport Stream The encoded data, carrying the video and audio signals, is internally multiplexed into the MPEG-4 and DVB compliant transport stream when the D9054 HD Encoder is used in a stand-alone or ROSA controlled application. When the D9054 HD ®...
Application Examples IP Distribution The D9054 HD encoder is designed for compression of high-quality services, including video, audio, data and ancillary services, over satellite. Users typically need to control multiple encoders in an automatically redundant system to securely transmit services to a large IP set-top box population. Typical solutions are targeted at programmers, broadcasters, service providers and private networks who have a particular interest in full turnkey solutions.
D9054 HD Encoder offer unique possibilities for optimizing the relations between delay and picture quality. Closed Captioning The D9054 HD Encoder supports closed captioning embedded in the HD-SDI signal as specified by SMPTE-292M. D9054 HDTV Encoder Intstallation and Operation Guide...
Audio and Data Interfaces Audio Input Four audio stereo channels can be input at the D9054 HD Encoder. Each of the audio inputs accept digital AES/EBU or embedded audio. You can assign the encoded audio channels, in multiples of two, to the video program or to independent audio only programs.
Page 36
• 32 kHz • 44.1 kHz • 48 kHz The D9054 HD Encoder locks the audio sampling frequency to the video. For AES/ EBU digital input signals, the D9054 HD Encoder automatically adapts the incoming rate by using sample rate conversion.
The outputs support SI generation with standard tables compliant to MPEG-2 and DVB. IP Transport Stream Outputs The D9054 HDTV Encoder has two IP TS outputs. These outputs can be used as inputs to IP networks. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Control and Management Interfaces Ethernet Management The D9054 HD Encoder features an Ethernet management interface which will support communication with the PNC system in the future. For information on the Ethernet management interface, see Connecting the Ethernet Management Interface, page 3-11.
Page 39
From ROSA you can update the D9054 HD Encoder software using FTP (File Transfer Protocol). A MIB file is included in the delivery from Cisco for the D9054 HD Encoder to support 3 party SNMP managers when the ROSA System is not utilized.
Chapter 3 Installation Overview Introduction This chapter describes how to install the D9054 HD Encoder. Before installing the D9054 HD Encoder, read all safety precautions and guidelines thoroughly. Qualified Personnel Only appropriately qualified and trained personnel should attempt to install, operate or maintain the D9054 HD Encoder.
AC power, see Appendix A - Technical Specifications. As Cisco units are designed for 24 hours’ operation, some products do not have a power switch. In this case the mains cord and/or DC power supply cable serve(s) as the mains disconnect device.
1U spacing between units to allow adequate ventilation/air flow. Cooling The D9054 HD Encoder is cooled by the use of internal fans. The air intake is from the front and the air outlet is on the rear. Note: Adequate cooling must be provided equalling 475 W per unit to avoid overheating.
Page 44
To connect AC power to the D9054 HD Encoder do the following: 1. Connect the power cords (supplied with the D9054 HD Encoder) between the rear panel power receptacles and a 100 to 120/200 to 240 V AC power outlet.
Contact Closure ASI Monitor Reference Outputs ASI Out 1 + 2 External Management 292M In and Out Data Outputs Digital Audio Reference Not Used Inputs Multiple Channel Audio (MCA) Rear Panel 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Page 46
Digital AES/EBU or embedded audio inputs. AES3/OUT, AES4/ Digital AES/EBU or embedded audio inputs, or reference outputs to support external audio encoding. Supports audio locked to internal video according to SMPTE-276M. D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
To Connect the Reference Input Do as follows to connect to the reference input: 1. Connect the reference input signal to the REF IN connector. Use a 75-ohm double-braided coax cable. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
AES3 and/or AES4 as Reference Outputs. From the GUI, you set up the D9054 HD Encoder to use either digital AES/EBU or embedded stereo inputs. The D9054 HD Encoder also supports encoding of audio embedded in the HD-SDI video signal.
Connecting to the Contact Closure Interface Contact Closure Connector The D9054 encoder has a contact closure interface which can be used to trigger digital program insertion (DPI). The contact closure interface has 8 inputs. Pin Allocation The connector labeled CONTACT CLOSURE is a 9-pin Sub-D connector (female).
A-alarm is active and the A-alarm LED lights on the front panel. Note: The A-alarm relay is always activated when the power is off or the D9054 HD Encoder is booting, whereas the other alarm relays maintain their status.
D9054 HD Encoder directly to another Ethernet device without using a hub or switch. You need to set up the IP address on both the D9054 HD Encoder (via the front panel display) or the ROSA driver for D9054 HD Encoder. For information on setting up the IP address via the front panel, see Front Panel Setup, page 1-3.
Note: You need a crossover cable if you want to connect the Ethernet interface of the D9054 HD Encoder directly to another Ethernet device without using a hub or switch. The equipment after the D9054 HDTV Encoder could be an IP router or a switch. 3-12 D9054 HDTV Encoder Intstallation and Operation Guide...
To Connect the ASI Outputs Do as follows to connect to the ASI output: 1. Connect the output signals from the D9054 HD Encoder connectors ASI OUT 1 and/or ASI OUT2 to the ASI input connectors of the equipment after the D9054 HD Encoder.
The only thing you need to set up via the front panel interface is the IP address of the Cisco D9054 HDTV Encoder. In this case the rest of the information in this chapter is for reference purposes only.
About the Front Panel Introduction The D9054 HD Encoder is operated using controls and indicators on the front panel. These include the numeric keypad, the Navigation/Selection keypad, the LCD, the ALARM and POWER indicators. These are shown in the following illustration:...
Page 57
SELECT (center key) or DOWN Arrow key selects the current item (this may go to a different menu or change a setting). Pressing the SELECT key stores any entered values. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
PREV MENU respective digit into a data entry field. F1 - F4 To be defined. a. Numeric keypad keys are uniform. MENU and PREV have been enlarged here for effect. D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
The video program name. The program name is set up from the GUI. IP Addr. Description: The IP address of the D9054 HD Encoder. The IP address is set up from the System menu, see IP, IP Address, page 4-24. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Main Menu Structure Operation of the HD Encoder Model D9054 begins at the Main menu. From the startup screen press the MENU or SELECT key to view the Main menu. Main Menu Video Audio Output System Lock 04-052 Menu Selection Select the desired function by moving the cursor left or right by pressing the LEFT or RIGHT key.
Services, <S1 to S8>, PMT PID Parameters: A figure between 16 and 8190. Description: The PMT PID assigned to the service. The default values for services 1 through 8 are 8021 to 8028 respectively. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Page 62
PSI Menu, Continued Services, <S1 to S8>, Prog Name Parameters: Up to 30 alphanumeric characters. Description: The name of the service. The supported character set is ASCII. D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
H.264, Video PID Parameters: A figure between 16 and 8190 Description: The PID of the video. Observe that you may not use the same PID for any other program element. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Page 64
Fixed is used for constant bit rate support. Variable (Capped VBR) is constrained to a maximum rate whereby Statmux allows you set video bit rate (i.e., minimum and maximum) which the encoder can operate within. 4-10 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 65
11.25 ≥4 The video bit rate must always be lower than the transport stream (TS) bit rate. For further information, see Transport Stream Rates for the Tributaries, page B-3. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 4-11...
Page 66
150,000 to 500,000, 128 x 96 resolution for 4:2:0 chroma format. Steps: 1 bit/s. Description: The capped video bit rate. Closed Caption, Control Parameters: Enable, Disable. Description: The closed caption status. 4-12 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Layer II, Dolby Digital, Linear/Dolby E, and AAC. Description: The D9054 HD Encoder can encode the audio input according to the Layer II, Dolby Digital, Dolby E, and AAC standards. It also accepts either a pre-encoded Dolby Digital input, Dolby E, or AAC input.
Page 68
Parameters: Digital, Embedded, Dolby-E Decoder. Description: The D9054 HD Encoder inputs the signal from the digital input connector in the selected format. If you select Embedded the D9054 HD Encoder extracts the audio embedded in the active SDI video signal of the program. The packet and pair is set in the GUI.
Page 69
Parameters: Digital, Embedded, Dolby-E Decoder. Description: The D9054 HD Encoder inputs the signal from the Digital input connector in the selected format. If you select Embedded the D9054 HD Encoder extracts the audio embedded in the active SDI video signal of the program. The packet and pair is set in the GUI.
Page 70
Mono (Center) 1/0 56 – 640 kbit/s 3/2 (L,R,C,Ls,Rs) 224 – 640 kbit/s Note: The 3/2 (L,R,C,Ls,Rs) mode is only available for encoders equipped with a Multiple Channel Audio (MCA) card. 4-16 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 71
It is recommended that you set the maximum data rate to that of the external Dolby Encoder. If the data rate of the Dolby Encoder is lower than the setting in the D9054 HD Encoder the audio will be passed through and only the actual bits in the data stream will be used.
Page 72
Parameters: Digital, Embedded. Description: The D9054 HDTV Encoder inputs the signal from the Analog/ Digital input connector in the selected format. If you select Embedded, the D9054 HDTV Encoder extracts the audio embedded in the active SDI video signal of the program. The packet and pair is set in the GUI.
Page 73
Parameters: Digital, Embedded, Dolby-E Decoder. Description: The D9054 HD Encoder inputs the signal from the Digital input connector in the selected format. If you select Embedded the D9054 HD Encoder extracts the audio embedded in the active SDI video signal of the program. The packet and pair is set in the GUI.
Page 74
Note: The 3/2 (L,C,R,Ls,Rs,LFE) mode is only available for encoders equipped with a Multiple Channel Audio (MCA) card. Note: The 3/2 (L,R,C,Ls,Rs) mode is only available for Ch 1 and Ch 4-20 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 75
AAC Encoder. If the data rate of the AAC Encoder is lower than the setting in the D9054 HD Encoder the audio will be passed through and only the actual bits in the data stream will be used.
In Packet mode you send a whole MPEG packet together (188/204 bytes) and have stuffing in between packets. In Burst mode you send 1 byte at a time with stuffing in between. Some non-Cisco decoders specifically require Packet or Burst mode.
Page 77
For the service selected, select the IP streaming mode. Note: You have to use the web GUI or the ROSA interface to set up the MAC and IP addresses of the receiver of the IP streaming packets. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 4-23...
Parameters: <0 to 255>.<0 to 255>.<0 to 255>.<0 to 255>. Description: The IP address of the management interface to the D9054 HD Encoder. Contact your network administrator to obtain an IP address. Use the numeric keys to type the IP address.
Page 79
Encoder to disable functionality. • If you have set or changed the IP address, subnet mask or gateway of one of the IP interfaces of the D9054 HD Encoder via the front panel display. Note: The reset may take up to 90 seconds.
Page 80
Press SELECT to default and UP or PREV to leave the menu without defaulting. Use the default settings if you have set up the D9054 HD Encoder with illegal and incompatible settings to get the encoder back in a functional state.
Page 81
The option is present and enabled. Disabled The option is present but has been disabled. In this case you have to enable the option to make it work. Please contact your local Cisco sales representative if you want to buy an option. Option License, DPI Parameters: Enabled, Disabled.
Page 82
The option is present and enabled. Disabled The option is present but has been disabled. In this case you have to enable the option to make it work. Please contact your local Cisco sales representative if you want to buy an option. Option License, AAC Parameters: Enabled, Disabled.
Page 83
Disabled The option is present but has been disabled. In this case you have to enable the option to make it work. Please contact your local Cisco sales representative if you want to buy an option. Option License, Dolby Digital Plus Parameters: Enabled, Disabled.
Page 84
Web GUI. Note: You must reboot the encoder to enable this feature; otherwise the last password used will be required to log on to the Web GUI. 4-30 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Setup and Monitoring Overview Control Modes You can set up and control the D9054 HDTV Encoder using the embedded Web interface, or a PC and the ROSA management system. Front Panel Keypad The operation of the D9054 HDTV Encoder can be monitored using the front panel keypad and LCD display.
Page 86
Overview, Continued In This Chapter This chapter describes how to set up and monitor the D9054 HD Encoder using the embedded Web interface. This interface looks identical whether you are using the embedded Web interface or the ROSA interface. This chapter contains the following topics.
Section D - Setting Up the VBI 5-86 Testing and Enabling Closed Captions 5-86 Section F - Setting Up the TS Output 5-96 Setting Up the TS Output Parameters 5-96 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Page 88
Viewing Messages 5-126 Viewing the Message Log 5-127 Setting Up the Trap Destinations 5-128 Removing a Trap Destination 5-130 Reading the Module Information 5-131 Setting the Date and Time Manually 5-132 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 89
Overview, Continued Topic See Page Setting the Clock Synchronization 5-133 Installing and Enabling Software Options 5-135 Setting Up the IP Network 5-137 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
3. When the GUI is configured for a user name and password, type the IP address of the D9054 HD Encoder to set up in the Address bar and press Enter. 4. Type the user name.
4. Type the new password once more. 5. Click OK. 6. Reset the D9054 HD Encoder. You reset the D9054 HD Encoder by pressing the Reset button from the System tab page. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Web Interface - Summary Screen To get an Overview of the Main D9054 HD Encoder Settings Proceed as follows to obtain an overview of the main D9054 HD Encoder settings: 1. Log on to the Web Interface. 2. Click the Summary tab.
Tab Pages Tab Pages The GUI of the D9054 HD Encoder has a number of tab pages. The function for the tab pages is as follows: • Summary From this page you can get an overview picture of the most important settings in the D9054 HD Encoder.
The Menu Bar and Buttons The Help Button The GUI of the D9054 HD Encoder has the following help button: The Table of Contents for the online help file is displayed when you click the Help button. The About Button...
Context-Sensitive Online Help Online Help Features The GUI of the D9054 HD Encoder has context-sensitive online help. Just press the help button in the GUI and the help belonging to the current window will display. Throughout the help system there are hypertext links to related topics.
To Set Up the Video Input Proceed as follows to set up the Video Input: 1. From the user interface of the D9054 HD Encoder, click the Video tab. 2. Select the Video Format. You may select 1080i/25 Hz, 1080i/29.97 Hz, 720p/50 Hz or 720p/59.94 Hz formats.
To Set Up the H.264 Video Encoder Proceed as follows to set up the Video Encoder: 1. From the user interface of the D9054 HD Encoder, click the Video tab and then the H.264 icon from the sub-pages. 2. Select Enable Encoder to enable the video encoder.
Page 98
When using Dynamic GOP, the GOP Length must be a multiple of 16 (i.e., 16, 32, 48, etc). 8. Type the GOP Length. The GOP length must be in the range from 1 to 255. 5-14 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 99
The 3:2 PDI feature is only applicable for the 1080i/29.97 Hz format. Note: Enabling 3:2 PDI increases the delay by 1 frame. Important: Do not enable or disable 3:2 PDI during live operation. The D9054 HD Encoder restarts if you enable or disable 3:2 PDI.
3:2 Pulldown Inversion The 3:2 PDI feature of the D9054 HD Encoder excludes the pictures of a 1080i/29.97 Hz video signal that have been duplicated through 3:2 pulldown, and allows the D9054 HD Encoder to encode the original frames at film rate. The data in the...
Page 101
Continued Encoder Behavior The 3:2 pulldown detector of the D9054 HD Encoder detects if there is a distinctive pattern of the 3:2 pulldown cadence, and controls the encoder actions, time stamping, etc. The D9054 HD Encoder tracks the input material and goes automatically and seamlessly in and out of 3:2 pulldown inversion, if the 3:2 PDI feature has been enabled.
Setting Up the H.264 Video Encoding Rate Proceed as follows to set up the Video Encoder: 1. From the user interface of the D9054 HD Encoder, click the Video tab, expand the H.264 icon and click the Encoding Rate icon from the sub-pages.
Page 103
GOP sequences and at full and 3/4 horizontal subsampling: Video GOP Lowest Recommended Minimum Sequence Bit Rate (Mbit/s) Full Horizontal 3/4 Horizontal Subsampling Subsampling 22.5 11.25 ≥4 5. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-19...
To Set Up the H.264 Video Encoding Parameters Proceed as follows to set up the H.264 Video Encoding Parameters: 1. From the user interface of the D9054 HD Encoder, click the Video tab, expand the H.264 icon and click the Parameters icon from the sub-pages.
To Set Up the H.264 Video Encoder Delays Proceed as follows to set up the Video Encoder Delays: 1. From the user interface of the D9054 HD Encoder, click the Video tab, expand the H.264 icon and click the Delays icon from the sub-pages.
To Set Up the H.264 Aspect Ratio Proceed as follows to set up the Aspect Ratio. 1. From the user interface of the D9054 HD Encoder click the Video tab, expand the H.264 icon and click the Aspect Ratio icon from the sub-pages.
Page 107
Receiver D9054 Encoder Set-Top Box Display Bar data signals one pair of bars only; either Top and Bottom Bars or Left and Right Bars. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-23...
Page 108
AFD 0100 (i.e., undefined/unknown). The Left Width and Right Width can be adjusted in the range from 0 to 640 pixels (up to half the screen width). 5. Click Apply. 5-24 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
PID, and unique service ID. Note: You need a statmux license for each D9054 HD Encoder that runs in statmux mode. Note: Ensure that all video programs are frame synchronized by an External Frame synchronizer (i.e., set Frame Synchronization to External Reference).
To Set Up the Statistical Multiplexing Encoding Rate Proceed as follows to set up the Statistical Multiplexing Encoding Rate: 1. From the user interface of the D9054 HD Encoder click the Video tab, expand the H.264 icon, expand the Statistical Multiplexing icon and click the Encoding Rate icon from the sub-pages.
Page 111
The legal range is from 3 to 20 Mbit/s for Main Profile encoding and 3 to 25 Mbit/s for High Profile encoding. The default video rate is the service’s contribution to the statmux pool when the D9054 HD Encoder participates in statistical multiplexing. During statistical multiplex operation, each D9054 HD Encoder that participates in statistical multiplexing will be granted capacity from the statmux pool.
Page 112
These delay figures do not include additional delay from the pre-processing. You select extended delay for applications where picture quality has priority to end-to-end delay. For the normal delay setting, the D9054 HD Encoder adheres strictly to the limitations in ISO/IEC 14496-1 (H.264 specification). You only select short delay for applications which require it as picture quality is likely to be reduced.
3. Use higher default video rates for any channels with full resolution and lower default video rates for any channels with reduced resolution. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-29...
To Set Up the Statistical Multiplexing Pools Proceed as follows to set up the Statistical Multiplexing Pools: 1. From the user interface of the D9054 HD Encoder click the Video tab, expand the H.264 icon, expand the Statistical Multiplexing icon and click the Pools icon from the sub-pages.
To Set Up the Statistical Multiplexing Clock Proceed as follows to set up the Statistical Multiplexing Clock: 1. From the user interface of the D9054 HD Encoder click the Video tab, expand the H.264 icon, expand the Statistical Multiplexing icon and click the Statmux Clock icon from the sub-pages.
To Set Up the Statistical Multiplexing Quality of Service Proceed as follows to set up the Statistical Multiplexing Quality of Service: 1. From the user interface of the D9054 HD Encoder click the Video tab, expand the H.264 icon, expand the Statistical Multiplexing icon and click the Quality of Service icon from the sub-pages.
Page 117
• When you select Custom as the QoS Mode, set the 8-bit field that contains the QoS bits. This value is a multiple of the value set for the Differentiated Service Code point. 3. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-33...
H.264 icon, expand the Statistical Multiplexing icon and click the Redundancy icon from the sub-pages. 2. Set the Role of the D9054 Encoder. The encoder’s role is normally set as Primary, but may be set to Secondary for use as a backup encoder.
To Monitor Statistical Multiplexing Proceed as follows to monitor Statistical Multiplexing: 1. From the user interface of the D9054 HD Encoder click the Video tab, expand the H.264 icon, expand the Statistical Multiplexing icon and click the Monitoring icon from the sub-pages.
Page 120
This is the encoding rate in bits/second for each of the encoders in the statmux pool. Leak Rate This is the leak rate of the encoders in the statmux pool. Leak rate is the transport packet output rate in bits/second. 5-36 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 121
This is the operating state of each of the encoder in the statmux pool, either Active or Standby. Algorithm ID These are the algorithm IDs assigned to each of the encoders in the statmux pool. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-37...
Page 122
Also, check that the following data remains constant for each Reload: • Pool Bandwidth • Number of entries in the list • DSP Comm Error Count • Network Comm Error Count 5-38 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
To Set Up the H.264 PIP Video Channel Proceed as follows to set up the H.264 PIP Video Channel: 1. From the user interface of the D9054 HD Encoder, click the Video tab, and click the PIP/H.264 icon from the sub-pages.
To Set Up the H.264 PIP Video Encoding Parameters Proceed as follows to set up the H.264 PIP Video Encoding Parameters: 1. From the user interface of the D9054 HD Encoder, click the Video tab, expand the PIP/H.264 icon and click the Encoding Parameters icon from the sub-pages.
To Set Up the Test Pattern Proceed as follows to set up the Test Pattern: 1. From the user interface of the D9054 HD Encoder, click the Video tab and click the Test icon from the sub-pages. 2. Set the mode of the test pattern.
To Set Up the Pre-Processor Parameters Proceed as follows to set up the Pre-processor: 1. From the user interface of the D9054 HD Encoder, click the Pre-Processor tab. The Enable Pre-Processor function is not applicable to the D9054 Encoder, and is disabled.
To Set Up the Pre-processor, Custom Filtering Proceed as follows to set up the Pre-processor, Custom Filtering: 1. From the user interface of the D9054 HD Encoder, click the Pre-Processor tab and click the Custom Filtering icon from the sub-pages.
Proceed as follows to select and enable audio channels: 1. From the user interface of the D9054 HD Encoder, click the Audio tab. 2. Select and enable the audio channel(s) you want to use by clicking on the cell in the table.
To Set Up the Layer II Audio Input Proceed as follows to set up the Layer II Audio Input: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the Layer II icon and click the appropriate channel icon from the sub-pages.
Page 130
4. Select in the Input Type field whether your audio input is Digital, Embedded, or Dolby-E Decoder. The D9054 HD Encoder inputs the signal from the Digital input connector in the selected format. If you select Embedded, the D9054 HD Encoder extracts the audio embedded in the active HD-SDI video signal of the program.
Page 131
Joint Stereo mode is highly recommended for data rates below 192 kbps. The Stereo mode should be used for data rates of 192 kbps and above. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-47...
Page 132
Note: You cannot set a positive relative audio delay greater than the end-to-end delay determined by the video encoder. 5-48 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 133
Full This setting provides the highest (full) bandwidth range regardless of audio quality; however, more coding artifacts will be audible than at the other settings. 14. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-49...
The default is selected. 4. Select Original if you want to signal that the encoded bit stream is an original. The default is selected. 5. Click Apply. 5-50 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Frequency Amplitude (dBFS) 125 Hz -1.05 500 Hz -1.05 1 kHz -1.05 1 kHz 21 dB -21.05 1 kHz 61 dB -61.05 2 kHz -1.05 10 kHz -1.05 Silence 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-51...
Page 136
Note: Digital Silence is used to create a stream with perfect (or digital) silence. Note: The test tone frequencies apply at a sampling frequency of 48 KHz. 3. Click Apply. 5-52 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Proceed as follows to set up the Dolby Digital audio: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the Dolby Digital icon and click the appropriate channel icon from the sub- pages.
Page 138
Note: The 3/2 (L,R,C,Ls,Rs) mode is only available for encoders equipped with a Multiple Channel Audio (MCA) card. Note: The 3/2 (L,R,C,Ls,Rs) mode is only available for Ch 1 and Ch 4. 5-54 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 139
6. Select in the Input Type field whether your audio input is digital, embedded, or Dolby-E Decoder. The D9054 HD Encoder inputs the signal from the Digital input connector in the selected format. If you select Embedded the D9054 HD Encoder extracts the audio embedded in the active HD-SDI video signal of the program.
Page 140
If you select Dolby-E Decoder (Pair 1 to 4), you must set up the Dolby-E Decoder in the Dolby-E Decoder page. For more information, see Setting up the Dolby-E Decoder (MCA card only), page 5-85. 5-56 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 141
Dolby Encoder. If the data rate of the Dolby Encoder is lower than the setting in the D9054 HD Encoder the audio will be passed through and only the actual bits in the data stream will be used.
Page 142
Note: You cannot set a positive relative audio delay greater than the end-to-end delay determined by the video encoder. For information about the video delay, see Setting Up the H.264 Video Encoder Delays, page 5-21. 12. Click Apply. 5-58 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
To Set Up the Dolby Digital Processing Proceed as follows to set up the Audio Dolby Digital Processing: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the Dolby Digital icon, expand the appropriate channel icon and click the Processing icon from the sub-pages.
Page 144
LFE channel. Otherwise, select Off. 10. Select the Surround 90 degrees Phase-Shift. Select On to apply a 90-degree phase shift to the surround channel. Otherwise, select Off. 5-60 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 145
The default is selected. 17. Select Original if you want to signal that the encoded bit stream is an original. The default is selected. 18. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-61...
To Set Up the Dolby Digital Channels Proceed as follows to set up the Dolby Digital Channels: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the Dolby Digital icon, expand the appropriate channel icon and click the Channels icon from the sub-pages.
Page 147
6. In Dual Mono 1+1 repeat steps 2 to 5 for the Aux channel. Note: These settings apply to the right channel. 7. Set the Center and Surround Downmix Level for Dolby Digital Surround 5.1, in 8. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-63...
To Set Up the Dolby Digital Extended BSI Proceed as follows to set up the Dolby Digital Channels: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the Dolby Digital icon, expand the appropriate channel icon and click the Extended BSI icon from the sub-pages.
To Set Up Dolby Digital Passthrough Proceed as follows to set up Audio Dolby Digital Passthrough: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the Dolby Digital icon, expand the appropriate channel icon and click the Passthrough icon from the sub-pages.
To Set Up Dolby Digital Test Tones Proceed as follows to set up the test tones: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the Dolby Digital icon, expand the appropriate channel icon and click the Test icon from the sub-pages.
Page 151
Note: The Chord test tone is only available for encoders equipped with a Multiple Channel Audio (MCA) card. Note: The test tone frequencies apply at a sampling frequency of 48 kHz. 3. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-67...
To Set Up AAC Audio Proceed as follows to set up AAC audio: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the AAC icon and click the appropriate channel icon from the sub-pages.
Page 153
5. Select in the Input Type field whether your audio input is digital, embedded, or Dolby-E Decoder. The D9054 HD Encoder inputs the signal from the Digital input connector in the selected format. If you select Embedded the D9054 HD Encoder extracts the audio embedded in the active HD-SDI video signal of the program.
Page 154
Decoder license. 3/2 (L,R,C,Ls,Rs) Digital (L,R), (C,LFE), and (Ls,Rs) for Digital Input Embedded (L,R), (C,LFE), and (Ls,Rs) for Embedded Input Dolby-E Decoder (L,R), (C,LFE), and (Ls,Rs) for Dolby-E Decoder Input 5-70 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 155
Note: There is no advantage to increasing the encoding sample rate above that of the input sample rate. Note: For the lowest audio bit rates it is often recommended to use the lowest sample rate for best quality. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-71...
Page 156
D9054 HD Encoder, the audio will be passed through and only the actual bits in the data stream will be used. Note: The external AAC Encoder must be locked to the clock of the D9054 HD Encoder. This can be achieved by connecting the Digital Output of the audio connector to the external encoder.
Page 157
Note: You cannot set a positive relative audio delay greater than the end-to-end delay determined by the video encoder. For information about the video delay, see Setting Up the H.264 Video Encoder Delays, page 5-21. 11. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-73...
To Set Up AAC Processing Proceed as follows to set up AAC Processing: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the AAC icon, expand the appropriate channel icon and click the Processing icon from the sub-pages.
Page 159
(This means the noise can appear shortly after or even before the exciter signal, so it's an intentional “post/pre-echo”, but not noticeable if implemented correctly, i.e., below the masking threshold.) 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-75...
Page 160
The default is selected. 7. Select Original if you want to signal that the encoded bit stream is an original. The default is selected. 8. Click Apply. 5-76 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
To Set Up AAC Passthrough Proceed as follows to set up the AAC Passthrough: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the AAC icon, expand the appropriate channel icon and click the Passthrough icon from the sub-pages.
To Set Up the AAC Test Tones Proceed as follows to set up the AAC Test Tones: 1. From the user interface of the D9054 HD Encoder, click the Audio tab, expand the AAC icon, expand the appropriate channel icon and click the Test Tones icon from the sub-pages.
Page 163
Note: The Chord test tone is only available for encoders equipped with a Multiple Channel Audio (MCA) card. Note: The test tone frequencies apply at a sampling frequency of 48 kHz. 3. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-79...
To Set Up the Linear/Dolby E Audio Proceed as follows to set up the Linear/Dolby E Audio: 1. From the user interface of the D9054 Encoder click the Audio tab, expand the Linear/Dolby-E icon and click the appropriate channel icon from the sub-pages.
Page 165
The legal range is from 0 to 2000 ms. If you use an external audio encoder which adds to the audio delay you type a delay value corresponding to the external audio delay. 10. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-81...
To Set Up the Linear Processing Proceed as follows to set up the Linear/Dolby-E Processing: 1. From the user interface of the D9054 Encoder click the Audio tab, expand the Linear/Dolby-E icon, expand the appropriate channel icon and click the Processing icon from the sub-pages.
To Set Up the Linear Parameters Proceed as follows to set up the linear parameters: 1. From the user interface of the D9054 Encoder click the Audio tab, expand the Linear/Dolby-E icon, expand the appropriate channel icon and click the Linear icon from the sub-pages.
To Set Up the Reference Output Proceed as follows to set up the reference output: 1. From the user interface of the D9054 Encoder, click the Audio tab and then the Reference Output icon from the sub-pages. 2. As the default, AES3 and AES4 are set as Reference Outputs. They may be configured as digital AES inputs if more inputs are required in addition to AES1 and AES2.
To Set Up the Dolby-E Decoder Proceed as follows to set up the Dolby-E Decoder: 1. From the user interface of the D9054 Encoder, click the Audio tab and then the Dolby-E Decoder icon from the sub-pages: 2. Select in the Input Type field whether your audio input is digital or embedded.
To Test and Enable Closed Captions Proceed as follows to test and enable closed captions: 1. From the user interface of the D9054 HD Encoder, click the VBI tab. 2. To enable closed captions select Enable in the Closed Captions Enable field. The selections are: Disable, 608 only and 708 only.
To Set Up the DPI via Contact Closure Proceed as follows to set up the DPI for up to eight contact closures: 1. From the user interface of the D9054 HD Encoder, click the DPI tab. The GUI displays the global DPI message information and trigger information for all eight DPI messages.
Page 172
This is the number of times the splice message is to be repeated. 7. Set the Interval. This is the repeat period for the number of repetitions of splice message generation. The default is 1000 ms. 5-88 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 173
PID. The Enable check box will be checked if any of the eight messages are enabled. The Trigger Information will also be displayed for the selected DPI message. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-89...
Page 174
19. Select DTMF Output Enable to generate a DTMF tone when the advertisement or break is to start or to set up the open-collector outputs for the Advanced D98xx series receivers (for example, Cisco D9854 Advanced Program Receiver and Cisco D9858 Advanced Receiver Transcoder), which supports decoding of SCTE-35 messages with DTMF descriptor.
Page 175
You can optionally configure the sequence to set the open-collector contacts for the Advanced D98xx series receivers (for example, Cisco D9854 Advanced Program Receiver and Cisco D9858 Advanced Receiver Transcoder). To set an open-collector contact, set two digits after */# to request a trigger output.
Page 176
Click Clear All to remove all the assigned tiers. Note: A maximum of 8 tiers can be selected. For example, the tier map below assigns tiers 106-107, 115-116, 135-136, and 140- 141 to the encoder. 5-92 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 177
Possible values are in the range of 0 to 60000 ms. The default value is 0 ms. Note: Pre-roll Delay must be less than the Break Duration. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-93...
Page 178
Proceed as follows to set up the DPI messages embedded in the HD-SDI input signal: 1. From the user interface of the D9054 HD Encoder, click the DPI tab. The GUI displays the global DPI message information. This page is also used to enable the DPI messages embedded within the HD-SDI signal (see step 8).
Page 179
PCR base value plus 4 seconds. If this was the case, it would mean that the splice was defined to occur before the packet is physically placed in the multiplex. 10. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-95...
To Set Up the TS Output Parameters Proceed as follows to set up the TS Output: 1. From the user interface of the D9054 HD Encoder, click the TS Output tab. 2. Enter the Output Bit Rate in bit/s. The legal range is from 1 to 120 Mbit/s. This bit rate must not be smaller than the Used Payload.
To Set Up the ASI Output Parameters Proceed as follows to set up the ASI output: 1. From the user interface of the D9054 HD Encoder, click the TS Output tab and the ASI icon from the sub-pages. The GUI displays the bit rate of the Used Payload if you press Reload.
Setting Up the IP Streaming Output The D9054 HD Encoder can stream IP to an IP network device with a defined MAC address and IP address on a selected IP subnet. Setup in the D9054 HD Encoder ROSA/Web Interface Proceed as follows to set up the IP Streaming Output: 1.
Page 183
11. Enter the number of transport packets (# TS Packets) per UDP. This sets the number of transport packets when UDP mode is selected. Choose a value in the range from 1 to 7. The default is 7. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-99...
Page 184
16. The D9054 HD Encoder can stream up to eight services on one IP output. Proceed as follows to set up each of up to eight services for each stream. From the user interface of the D9054 HD Encoder click the TS Output tab and the IP Service Selection icon from the sub-pages.
Page 185
Refer to RFC 2474 and RFC 3260. Supports configuration of TOS bits in the IP header, allowing integration in Diff Serve networks. ToS/CoS (Precedence) Type of service precedence. Refer to RFC 791. Custom Refer to RFC 3168. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-101...
Page 186
When you select Custom as the QoS Mode, set the 8-bit field that contains the QoS bits. This value is a multiple of the value set for the Differentiated Service Code point. 20. Click Apply. 5-102 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Enabling/Disabling the PSI/SI Information Proceed as follows to enable or disable the PSI/SI information: 1. From the user interface of the D9054 HD Encoder click the PSI tab. 2. To enable the PSI/SI information, select DVB or MPEG. The default setting is Off.
To Set Up the Transport Stream Proceed as follows to set up the Transport Stream: 1. From the user interface of the D9054 HD Encoder, click the PSI tab and the Transport Stream icon from the sub-pages. 2. Type the Network ID.
To Set Up the Service Stream Proceed as follows to set up the Service Stream: 1. From the user interface of the D9054 HD Encoder, click the PSI tab and the Service Setup icon from the sub-pages. 2. Enter the Name of the service. This field can be up to 30 characters in length and can consist of any printable character.
To Set Up the Video Program Proceed as follows to set up the Video Program: 1. From the user interface of the D9054 HD Encoder, click the PSI tab and the Video icon from the sub-pages. 2. Enter the PID for the Video channel.
Proceed as follows to set up the Layer II Audio Program: 1. From the user interface of the D9054 HD Encoder, click the PSI tab, expand Audio and then the Layer II icon and click one of the channel icons from the sub-pages.
Page 192
6. If relevant, repeat steps 2 to 5 for the other audio channel. 7. Click Apply. 5-108 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
To Select the Dolby Digital Audio Descriptor Mode Proceed as follows to select the Dolby Digital Audio Descriptor Mode: 1. From the user interface of the D9054 HD Encoder, click the PSI tab, expand the Audio icon and click the Dolby Digital icon from the sub-pages.
Proceed as follows to set up the Dolby Digital Audio Program: 1. From the user interface of the D9054 HD Encoder, click the PSI tab, expand the Audio icon, expand the Dolby Digital icon and click one of the channel icons from the sub-pages.
Page 195
TV service which delivers a verbal description of the visual scene as an aid to understanding and enjoyment for e.g., viewers who have visual impairments. 6. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-111...
Proceed as follows to set up the AAC audio program: 1. From the user interface of the D9054 HD Encoder, click the PSI tab, expand the Audio icon, expand the AAC icon and click one of the channel icons from the sub-pages.
Page 197
8. Select the AAC LOAS Descriptor Format to use for AAC LOAS audio channels. There are two different formats: DVB (default) or MPEG. Select Both if you want to send DVB and MPEG descriptors. 9. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-113...
You must type in three letters. The supported languages are according to ISO 639-2. The audio language is signalled in a PSI table and used by satellite receivers. 1)Note that the DVB tables use the PIDs from 16 to 20. 5-114 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 199
TV service which delivers a verbal description of the visual scene as an aid to understanding and enjoyment for e.g. viewers who have visual impairments. 6. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-115...
To Set Up the NIT Proceed as follows to set up the NIT: 1. From the user interface of the D9054 HD Encoder, click the PSI tab and then the NIT icon from the sub-pages. 2. Select the relevant Delivery Type.
To Set Up the Cable NIT Proceed as follows to get access to the Cable NIT display: 1. From the user interface of the D9054 HD Encoder, click the PSI tab, expand the NIT icon and click the Cable icon from the sub-pages.
To Set Up the Satellite NIT Proceed as follows to get access to the Satellite NIT display: 1. From the user interface of the D9054 HD Encoder, click the PSI tab, expand the NIT icon and click the Satellite icon from the sub-pages.
To Set Up the Terrestrial NIT Proceed as follows to get access to the Terrestrial NIT display: 1. From the user interface of the D9054 HD Encoder, click the PSI tab, expand the NIT icon and click the Terrestrial icon from the sub-pages.
4. If relevant, click Reset to reset (boot) the D9054 HD Encoder. Hint: You should reset the D9054 HD Encoder if you have set or changed the IP address of the encoder via the front panel display.
Page 205
Important: You must give the file name the extension “.ini” in order to be able to see it when you want to Transfer Settings File To Device. 6. If relevant, upgrade the software of your D9054 Encoder. Ensure that the software application you want to upgrade to is located in a directory/location on your PC before proceeding with the upgrade.
To Read the D9054 HD Encoder Temperatures Proceed as follows to read the D9054 HD Encoder temperatures: 1. From the user interface of the D9054 HD Encoder, click the System tab and the Temperatures icon from the sub-pages. The GUI automatically displays the temperatures measured by the sensors in the D9054 HD Encoder.
To Read the Message Status Proceed as follows to read the message Status: 1. From the user interface of the D9054 HD Encoder click the System tab and the Message Status icon from the sub-pages. The Message Status table displays a list of all the pending messages in the D9054 HD Encoder system.
To Set Up the Message Parameters Proceed as follows to set up the message parameters: 1. From the user interface of the D9054 HD Encoder, click the System tab and the Message Settings icon from the sub-pages. The Message Settings table displays a list of all available Messages in the D9054 HD Encoder system.
Page 209
User’s Guide, part number 6985066. If the Trigger Backup box is checked the ROSA Element Manager will poll the encoder to check whether the alarm event occurs. 6. Click Apply. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 5-125...
Viewing Messages Before You Begin Before you can view any messages from the D9054 HD Encoder in ROSA you must set up the trap destination for the messages. For further information, see Removing a Trap Destination, page 5-130. Overview When viewing messages you can specify which columns to show for each message and the order in which they are shown.
To View the Message Log Proceed as follows to view the message log: 1. From the user interface of the D9054 HD Encoder, click the System tab and the Message Log icon from the sub-pages. ROSA automatically displays: •...
To Set Up the Trap Destination Proceed as follows to set up the trap destination: 1. From the user interface of the D9054 HD Encoder, click the System tab and the Trap Destination icon from the sub-pages. 2. Click Add Row.
Page 213
7. If relevant, change the Row Status for the SNMP trap. The row status indicates whether the receiving unit is active or not in service. Note: D9054 HD Encoder will not begin to send traps to the destination until you set the row status to Active and click Apply.
To Remove a Trap Destination Proceed as follows to remove a trap destination: 1. From the user interface of the D9054 HD Encoder, click the System tab and the Trap Destination icon from the sub-pages. 2. Click in the left column outside the row you want to delete.
Reading the Module Information Proceed as follows to read the module Information: 1. From the user interface of the D9054 HD Encoder, click the System tab and the Modules icon from the sub-pages. ROSA automatically displays: • the system configuration number, •...
Setting the Date and Time Manually Proceed as follows to set the Date and Time: 1. From the user interface of the D9054 HD Encoder, click the System tab and the Clock icon from the sub-pages. ROSA displays the internal date and time of the D9054 HD Encoder.
Setting the Clock Synchronization Proceed as follows to set the Clock Synchronization: 1. From the user interface of the D9054 HD Encoder, click the System tab, expand the Clock icon and click the Synchronization icon from the sub-pages. ROSA displays the existing clock synchronization of the D9054 HD Encoder.
Page 218
Note: After loss of power and after reset, the time setting is lost. If synchronization is enabled, the time is sent from the Copernicus/ROSA PC clock at the next synchronization. 5-134 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Cisco. Do as follows to install a new software option: 1. From the user interface of the D9054 HD Encoder click the System tab and then the Option License icon from the sub-pages. ROSA automatically displays a list of available options and their status. The Host ID field uniquely identifies the D9054 HD Encoder you are working on.
Page 220
2. Select Enable or Disable from the list. The Installation Status field is a read-only field. 3. Click Apply. 4. Click Reload to refresh/update the status after the license is installed. 5-136 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
To Set up the Management and IP Ports Before you can communicate with third party management devices or stream video to a set top box, you need to set up the IP parameters of the D9054 Encoder data Management and Ethernet ports.
Page 222
(with the same IP address) to downstream equipment. This does not require resetting of the encoder(s). 8. Click Apply. 5-138 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Service and Maintenance Overview Introduction This chapter gives information to assist you in upgrading firmware to the D9054 HD Encoder and replacing the fan assembly. It also describes how the status of the D9054 HDTV Encoder is communicated via front panel LEDs.
To Upload Firmware to the D9054 HD Encoder Do as follows to upload a new firmware version to the D9054 HD Encoder: 1. From the user interface of the D9054 HD Encoder click System to display the System page. 2. Click Upgrade to display the Upgrade Application window.
Introduction Overview To help signal the status of operation or the presence of an alarm, the D9054 HD Encoder makes use of front panel LEDs. The photograph below shows the location of the LEDs on the front panel of the D9054 HD Encoder.
Before You Start If you have a ROSA system, messages from the D9054 HD Encoder are shown in the Copernicus Server Explorer tree. You define and set up the status of the messages from the Message Settings page in the D9054 HD Encoder GUI.
Page 227
Remedy: Increase the bit rate. output rate Description: The incoming bit rate on Minor AAC: passthrough is higher than the encoder Passthrough setting. input rate higher than requested Remedy: No action required. output rate 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Page 228
Remedy: Check whether changes in audio content are expected. The message serves as information only. AAC: DSP Description: DSP hardware failure. Minor hardware failure Remedy: Contact the closest Cisco customer support center for assistance. D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 229
Description: Backup is required. One of Critical None the events configured to trigger a backup event has occurred. Remedy: Look at the other messages to find the cause of the event. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Page 230
The audio input level is too Overload on the high and close to the clipping level. audio input Remedy: Increase the clipping level or signal reduce the input level. D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 231
Minor Dolby Digital: passthrough is higher than the encoder Passthrough setting. input rate higher than requested Remedy: Increase the encoder setting to output rate match the maximum incoming stream rate. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Page 232
The encoding will restart. Remedy: Check the settings. Change the audio encoding rate or increase the TS rate. If a FIFO error occurs recurrently, contact the closest Cisco customer support center. 6-10 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 233
The encoding will restart. Remedy: Check your settings for parameter violations. Observe the limitations in the manual. If persistent, contact the closest Cisco customer support center for assistance. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 6-11...
Page 234
(either blackburst sources to the encoders or video sources to encoders are not in sync depending on which method is being used). 6-12 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 235
Remedy: If the error is not resolved immediately, power-cycle the encoder. If this does not correct the issue, contact the closest Cisco customer support center for assistance. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 6-13...
Page 236
Remedy: If the error is not resolved immediately, power-cycle the encoder. If this does not correct the issue, contact the closest Cisco customer support center for assistance. 6-14 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 237
Video, ensure that all sources are set to the same Video Format. If the clock source is set to External Reference, check the reference source. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 6-15...
Page 238
Major delay error implement the requested audio delay. Remedy: Decrease the audio data rate or change video settings to decrease end-to- end delay. Check relative and external delay settings. 6-16 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 239
Description: The audio delay setup on the Major Layer II: Audio DSP is too low. Requested audio encoding delay Remedy: Increase the audio delay. set too low 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 6-17...
Page 240
The audio input level is too Overload on the high and close to the clipping level. audio input Remedy: Increase the clipping level or signal reduce the input level. 6-18 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 241
Remedy: Apply passthrough signal. sync words Description: The passthrough input Major Linear/Dolby E: header is corrupted or invalid. Passthrough header corrupted Remedy: Correct the passthrough input or invalid header. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 6-19...
Page 242
Description: Power supply 1 has failed. Major failure Remedy: Replace the power supply. Power supply 2 Description: Power supply 2 has failed. Major failure Remedy: Replace the power supply. 6-20 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 243
Description: An error in the RS-232 Major interface error statmux interface has been detected. Remedy: Check that the RS-232 cabling is OK and that the equipment connected to the RS-232 interface operates as required. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 6-21...
Page 244
The option Description: An option license file is Information None import string is invalid. invalid Remedy: Check the Host ID and the ordered options in the option license file. 6-22 D9054 HDTV Encoder Intstallation and Operation Guide 4038938 Rev A...
Page 245
Remedy: Change the video bit rate or change other video settings to decrease the end-to-end delay. Alternatively, increase the specified delay. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide 6-23...
Section C - Power Supply Replacement Introduction Removal and Replacement There are no user-serviceable parts in the D9054 HDTV Encoder power supplies. If one of the power supplies requires replacement, contact Cisco for information on how to obtain a replacement power supply.
Introduction Removal and Replacement If either the filter or one of the four fans requires replacement, contact Cisco for a new filter or a fan replacement kit for the specific fan. Note: There are three different fans (two being the same) in the D9054 HDTV Encoder.
Chapter 7 Customer Information Overview In This Chapter This chapter contains the following topics. Topic See Page Product Support Returning Products 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
When returning equipment, the customer is solely responsible for equipment packaging and transportation costs to the factory. At the customer's request, Cisco will make reasonable efforts to provide warranty service at the customer's premises, provided that the customer pays current field service rates plus direct travel and accommodation expenses.
Page 251
In Case of Repair If your product requires repair, perform following steps. 1. Notify Cisco of the problem immediately, providing the model number and serial number of the equipment plus details of the problem. On receipt of this information, service information and shipping instructions will be provided.
You must have a return material authorization (RMA) number to return a product. Contact the nearest customer service center and follow their instructions. Returning a product to Cisco for repair includes the following steps: • Obtaining a RMA number • Obtaining a customer service center shipping address •...
Page 253
3. Ship the product to the address provided by the customer service representative. Note: Cisco does not accept freight collect. Be sure to prepay and insure all shipments. 4038938 Rev A D9054 HDTV Encoder Intstallation and Operation Guide...
Appendices Appendix A - Technical Specifications Appendix B - Transport Stream Rates Appendix C - ISO 639-2 Language Codes Appendix D - Equipment and Accessories Appendix E - Compliance Appendix F - References...
Page 257
Appendix A Technical Specifications Overview Introduction This appendix contains the technical specifications for the D9054 HDTV Encoder. Note: The technical specifications are subject to change without prior notice. In This Appendix This appendix contains the following topics. Topic See Page...
H.264 Main Profile Picture size 192 x 192 or 128 x 96 Bit rate 200 to 500 kbit/s, 192 x 192 resolution 150 to 500 kbit/s, 128 x 96 resolution D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
≥ 15 dB in the range 5 to 1000 MHz Return loss ≥ 12 dB in the range 1000 to 1485 MHz Jitter acceptance According to SMPTE RP184 Interference rejection No bit errors in presence of superimposed interfering signal 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
ETSI TS 101 154 AAC mode General ARIB STD-B39 Embedded Audio Item Specification Format According to SMPTE-299M Audio sampling frequency 48 kHz locked to the video. According to SMPTE-272M Resolution 20 bits D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
1 to 120 Mbit/s ± 100 ppm Transport stream formats According to EN 50083-9. 188 bytes structure, 204 bytes without Reed Solomon, Burst or packet format. ASI bit rate 270 Mbit/s ± 100 ppm 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
2 lines of 40 characters backlit LCD. Keypad Arrow keys, 0 to 9, Select, Menu and Prev keys, F1 to F4 LEDs Green LED for Signal status. Red LED for Alarm indication. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
For example: Ensure that the socket outlet is installed near the product. WARNING: To avoid electrical shock, connect the three-prong plug on this product to an earth-grounded three-pin socket outlet only. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 266
Power, Continued Architecture The following diagram illustrates the power supply architecture. A-10 D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
-10 to +70°C (14 to 158°F) Operation Humidity 5 to 95% non-condensing Temperature 0 to +40°C (32 to 104°F) Altitude Operating 10,000 ft. (3,048 m) max. Non-operating 30,000 ft. (9,144 m) max. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide A-11...
Also, it presents the available transport stream rates on an ASI network. In This Appendix This appendix contains the following topics. Topic See Page Introduction Transport Stream Rates for the Tributaries Available Rate on the Transmission Media B-10 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 270
The D9054 HDTV Encoder automatically allocates the necessary transport stream rates for the chosen tributary rates. With the following tables at hand, you may prepare and evaluate a rate budget for the D9054 HD Encoder before actual configuration. The transport stream rates for the tributaries are, apart from the video and audio rounded up to the nearest kbit/s.
The SI/PSI rate for the video program is 53 kbit/s. If you, besides the video program, have an additional audio only program this takes up 33 kbit/s. To help you to calculate the total TS rate used by the D9054 HD Encoder the following sections show the transport stream rates of each tributary.
Page 272
329 kbit/s 384 kbit/s 396.9 kbit/s 395.8 kbit/s 399.5 kbit/s a. Applies to 188-byte packet mode. If 204-byte packet mode is used you must multiply by a factor of 204/188. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 273
336.8 kbit/s 384 kbit/s 396.9 kbit/s 395.8 kbit/s 399.5 kbit/s a. Applies to 188-byte packet mode. If 204-byte packet mode is used you must multiply by a factor of 204/188. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 274
593.4 kbit/s 640 kbit/s 658 kbit/s 658.5 kbit/s 658 kbit/s a. Applies to 188-byte packet mode. If 204-byte packet mode is used you must multiply by a factor of 204/188. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 275
593.4 kbit/s 640 kbit/s 658 kbit/s 658.5 kbit/s 658 kbit/s a. Applies to 188-byte packet mode. If 204-byte packet mode is used you must multiply by a factor of 204/188. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 276
370125 370125 384 kbit/s 404824 405375 404824 405375 399500 405375 a. Applies to 188-byte packet mode. If 204-byte packet mode is used you must multiply by a factor of 204/188. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 277
599250 599250 640 kbit/s 663912 669750 672008 669750 663875 663875 a. Applies to 188-byte packet mode. If 204-byte packet mode is used you must multiply by a factor of 204/188. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
(1/2, 2/3, 3/4, 5/6 and 7/8). The transport stream rate of the D9054 HD Encoder shall be set up to equal the rate calculated by the formula above. Remember to disable the RS in the D9054 HD...
Standard Codes for the Representation of Names of Languages according to ISO 639-2. In This Appendix This appendix contains the following topics. Topic See Page Language Codes - Sorted by Alpha 3-Letter Code (ISO 639-2) 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Code Abkhazian Afar Afrikaans Albanian alb/sqi Amharic Arabic Aragonese Armenian arm/hye Assamese Avestan Aymara Azerbaijani Bashkir Basque baq/eus Belarusian Bengali Bihari Bislama Bosnian Breton Bulgarian Burmese bur/mya Catalan Chamorro Chechen D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 281
Czech cze/ces Danish Dutch dut/nld Dzongkha English Esperanto Estonian Faroese Fijian Finnish French fre/fra Frisian Gaelic Gallegan Georgian geo/kat German ger/deu Greek, (1453-) Guarani Gujarati Haitian Hausa Hebrew Herero 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 282
Language Code Code Hindi Hiri Hungarian Icelandic ice/isl Indonesian Interlingua Interlingue Inuktitut Inupiaq Irish Italian Japanese Javanese Kalaallisut Kannada Kashmiri Kazakh Khmer Kikuyu; Kinyarwanda Kirghiz Komi Korean Kuanyama; Kurdish Latin Latvian D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 283
Macedonian mac/mkd Malagasy Malay may/msa Malayalam Maltese Manx Maori mao/mri Marathi Marshallese Moldavian Mongolian Nauru Navaho, Ndebele, Ndebele, Ndonga Nepali Northern Norwegian Norwegian Norwegian Nyanja Occitan (post 1500) Oriya Oromo 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 284
Persian per/fas Polish Portuguese Pushto Quechua Raeto-Romance Romanian rum/ron Rundi Russian Samoan Sango Sanskrit Sardinian Serbian scc/srp Shona Sichuan Sindhi Sinhalese Slovak slo/slk Slovenian Somali Sotho, Spanish; Sundanese Swahili Swati D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 285
Swedish Tagalog Tahitian Tajik Tamil Tatar Telugu Thai Tibetan tib/bod Tigrinya Tonga Tsonga Tswana Turkish Turkmen Uighur Ukrainian Urdu Uzbek Vietnamese Volapuk Walloon Welsh wel/cym Wolof Xhosa Yiddish Yoruba Zhuang; 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 286
Language Code Code Zulu a. Languages that have two synonymous codes. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
This appendix contains names and part numbers of options and accessories for the D9054 HD Encoder. In This Appendix This appendix contains the following topics. Topic See Page Accessory Kits for the D9054 HD Encoder Options and Upgrades 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Description 4038938 Rev A Cisco D9054 HDTV Encoder, Installation and Operation Guide The following line cords may be ordered for use with the D9054 HD Encoder: 180178 Line cord, 125 V, Australian version 207340 Line cord, 250V, 10 A, Argentina...
Options and Upgrades Software Options The following software options are available: Note: Contact a Cisco sales representative if you want to purchase an option. Part number Description 4012577.0001 Dolby Digital (AC-3) 2.0 encoding, channel 1 and 2 4012577.0021 Dolby Digital (AC-3) 2.0 encoding, channel 3 and 4 4012577.0031...
Appendix E Compliance Applicable Standards and Notices Safety The D9054 HDTV Encoder has been approved for safety by the Standards Council of Canada and the OHSA (NRTL) Accredited Testing Laboratory to the following standards: CAN/CSA-C22.2 No. 60950-1-03 ANSI/UL Std No. 60950-1-2003...
Page 292
The manufacturer is not responsible for any radio or TV interference resulting from unauthorized modifications made to this equipment. It is the responsibility of the user to correct such interference at his own expense. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 293
Scientific Atlanta Canada Inc (Digital Media Networks Business Unit) (Company name) 100 Middlefield Road, Scarborough Ontario Canada M1S 4M6 (Company Address) For the manufacturer: Steven Lawrence, Product Regulatory Compliance (Signature, Name and Title) 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
1992 CCITT Rec Information technology - Open Systems Interconnection - Systems Management: x.736, 01 Security alarm reporting function 1992 CSA C 22.2 Safety of information technology equipment No. 60950, 2000 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 296
Basic Environmental Testing Procedures. 68-2-56 IIEEE 802.3, 1996 IEEE Standard for Local and metropolitan area networks. Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 297
24-Bit Digital Audio Format for HDTV Bit. Serial Interface. SMPTE 333M, 1999 Television - DTV Closed-Caption Server to Encoder Interface. SMPTE 334M, 2000 Vertical Ancillary Data Mapping for Bit-Serial Interface. 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide...
Page 298
“Digital Video Broadcasting (DVB); Implementation guidelines for the use of MPEG-2 systems; Video and audio in satellite, cable and terrestrial broadcasting applications.” UL 60950-1, 2003 Safety of information technology equipment. D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Picture in Picture Program Specific Information. Normative data necessary for the demultiplexing of TSs and the regeneration of programs. Quadrature Amplitude Modulation. QAM is a method of 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide Glossary-1...
Page 300
Simple Network Management Protocol. SNMP is an internet standard protocol developed to manage nodes such as servers, workstations, routers, switches and hubs on an IP network. Synchronous Parallel Interface Transport Stream Variable Bit Rate Glossary-2 D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Ethernet interface management front panel setup 3-11 3-12 3-13 4-24 SMPTE 292M overview 2-11 video input specifications contact control ethernet interface connector pin allocation 3-11 3-12 pin allocation 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide Index-1...
Page 302
5-50 setting up 5-44 5-45 setting up test tones 5-103 5-104 5-105 5-51 layer II encoding front panel setup 4-15 overview specifications LEDs linear audio encoding specifications Index-2 D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 303
5-120 setting up delay 5-20 5-39 5-40 system controller version 5-120 video input software upload connector software version front panel setup device driver 5-120 setting up 5-12 specifications 4038938 Rev A D9054 HDTV Encoder Installation and Operation Guide Index-3...
Page 304
Index, Continued Web interface log on summary screen Index-4 D9054 HDTV Encoder Installation and Operation Guide 4038938 Rev A...
Page 306
Lawrenceville, GA 30042 www.cisco.com This document includes various trademarks of Cisco Systems, Inc. Please see the Notices section of this document for a list of the Cisco Systems, Inc. trademarks used in this document. Product and service availability are subject to change without notice.