Zoom Yes Wimax User Manual
  1. Manuals
  2. Brands
  3. Zoom Manuals
  4. Gateway
  5. Yes Wimax
  6. User manual

Zoom Yes Wimax User Manual

Wimax & wifi gateway
Hide thumbs
Table of Contents

Advertisement

Quick Links

Zoom
WIMAX & WIFI Gateway

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Yes Wimax and is the answer not in the manual?

Questions and answers

Related Manuals for Zoom Yes Wimax

Summary of Contents for Zoom Yes Wimax

  • Page 1 Zoom WIMAX & WIFI Gateway...

  • Page 2: Table Of Contents

    Zoom User Manual V1.0 Contents Contents..................1 About this Manual................4 Purpose ..................4 Prerequisite Skills and Knowledge ............4 Conventions Used in this Document ............5 Chapter 1 – Introduction............... 6 Product Overview ................6 Product Package ................7 Connectors ...................
  • Page 3 Zoom User Manual V1.0 User Interface Introduction ..............19 Basic Setup ................. 20 Step1 : Yes ID ................20 Step2 : Device SSID ............... 21 Confirmation (Step3) ..............23 Complete (Step4) ................24 Status ..................25 Status | WiMAX Status ..............25 Status | Device Status ..............
  • Page 4 Zoom User Manual V1.0 Network | Internet Protocol ............... 37 Network | DHCP Server ..............38 Network | Lease Reservation ............... 40 Network | Port Forwarding ..............41 Management .................. 42 Management | Password ..............42 Management | Device Time ..............44 Management | Device Name ..............

  • Page 5: About This Manual

    Zoom User Manual V1.0 About this Manual Purpose This document provides information and procedures on installation and configuration of Zoom WiMax and WiFi Gateway. You could utilize the theoretical information in this guide to setup your device. Prerequisite Skills and Knowledge To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures.

  • Page 6: Conventions Used In This Document

    Zoom User Manual V1.0 Conventions Used in this Document The following typographic conventions and symbols are used throughout this document: Very important information. Failure to observe this may result in damage. Important information that should be observed. Additional information that may be helpful but which is not required.

  • Page 7: Chapter 1 - Introduction

    Chapter 1 – Introduction Product Overview Thank you for choosing Zoom WIMAX and WIFI Gateway. Zoom WIMAX and WIFI Gateway is an all-in-one device that integrates WiMAX, Wi-Fi and VoIP service. Compliant with IEEE 802.16e WiMAX standard and Wi-Fi 802.11b/g/n, Zoom provides extended coverage and high performance wireless connectivity with minimized capital expenses.

  • Page 8: Product Package

    Zoom User Manual V1.0 Product Package Item Zoom WIMAX and WIFI Gateway. User Manual Power Adapter RJ-45 Ethernet cable If any of the items mentioned above are missing or damaged, please contact our customer support immediately.

  • Page 9: Connectors

    1. WPS Button: Press WPS button to establish wireless connection without setup the device. Step1: Press the WPS button on Zoom, and the WPS LED indicator will start flashing. Step2: And then press the WPS button on the client you wish to connect within 2 minutes.
  • Page 10 Zoom User Manual V1.0 4. LAN Port (RJ-45): This port is for connecting the device to your PC or other network equipment (such as hubs or switches) with an RJ-45 Ethernet cable. 5. DC-12V Port (Power Adapter Socket): Connect the power adapter...

  • Page 11: Led Indicators

    Zoom User Manual V1.0 LED Indicators Description AC Input not active or Power Fail Power Power On LAN Device Disconnect Ethernet LAN Device Connect Flashing Data Packet Transmit VoIP disable (Not registered or RJ11 not connected) VoIP Device registered and on hook...

  • Page 12: Chapter 2 - Installation

    Zoom User Manual V1.0 Chapter 2 – Installation Please follow the steps below to install the device: Step 1: Place the device on a flat work surface. Step 2: Connect the device Ethernet port to your PC with an RJ-45 Ethernet cable that is supplied.
  • Page 13 Zoom User Manual V1.0 Step 7: Select Local Area Connection Status from the Windows task bar and click Properties. Local Area Connection Status...
  • Page 14 Zoom User Manual V1.0 Step 8: Double click on the Internet Protocol (TCP/IP). Local Area Connection Properties...
  • Page 15 Zoom User Manual V1.0 Step 9: Select Obtain an IP address automatically and click OK. Step 10: At this point, the device should have been connected to the WiMAX Base station successfully. This can be verified by observing the signal strength LEDs (Please refer to Visual Indications section in Chapter 1 of this manual to find the location of these LEDs on the device).

  • Page 16: Chapter 3 - Web Interface

    Zoom User Manual V1.0 Chapter 3 – Web Interface Please follow the steps below to configure your device through the web interface: Step 1: Open the Web browser and enter the default IP address of the device, which is: http://192.168.1.1/...
  • Page 17 Zoom User Manual V1.0 Step 2: Enter the administrator login password to access web management interface. The default Password is admin. Welcome Page...
  • Page 18 Zoom User Manual V1.0 Step 3: The page shown here will be displayed on your browser after login. You can now configure the device settings. User Interface...

  • Page 19: Chapter 4 - Reference Manual

    Zoom User Manual V1.0 Chapter 4 – Reference manual The main menu is located on the left side of the screen and each main menu item contains sub-items on the top right of the screen. You can refer to the menu structure below:...

  • Page 20: User Interface Introduction

    Zoom User Manual V1.0 User Interface Introduction Reboot/Logout/Reconnect There are 3 buttons in the lower left corner. Clicking Reboot will restart your device. Click the Logout button to logout from the web interface. When the Reconnect button is clicked the device will attempt reconnection to the Base Station.

  • Page 21: Basic Setup

    Zoom User Manual V1.0 Basic Setup Basic Setup is just like a simple setup wizard that could help you setup your device by following the steps. Step1 : Yes ID Please enter the Yes ID and Password on the Yes Card provided in the product package for the first time.

  • Page 22: Step2 : Device Ssid

    Step2 : Device SSID Network Name (SSID): Define the service set identifier that represents the “name” of your network. (Default value will be “Yes Zoom” - “last 6 digits of your device MAC Address”) SSID Broadcast: Broadcast your SSID into open air by checking this checkbox that is checked in default.
  • Page 23 Zoom User Manual V1.0 Security: Check this checkbox to enable Wi-Fi Protected Access (WPA) wireless security. Key Pass Phrase: This field will appear if you Basic Setup > Step2 : Device SSID > WPA Key enable the option above. Enter the key you would like to use for your wireless security in 8~63 characters or 64 hex digits.

  • Page 24: Confirmation (Step3)

    Zoom User Manual V1.0 Confirmation (Step3) You can double confirm the input data in the previous setup process here. <<Back Button: Click Back button to go back to the previous setup process. Done Button: Click Done button to finish setup process.

  • Page 25: Complete (Step4)

    Zoom User Manual V1.0 Complete (Step4) The setup wizard is complete! You can view the status by clicking on the Status page link (in blue) to redirect to the Status page. Basic Setup > Complete...

  • Page 26: Status

    Zoom User Manual V1.0 Status Status | WiMAX Status Select Status > WiMAX Status to display the WiMAX connection status. Refresh Button: Click the Refresh button to refresh the current WiMAX connection status. Auto Button: Click the Auto button to update the status information periodically.

  • Page 27: Status | Device Status

    Zoom User Manual V1.0 Status | Device Status Select Status > Device Status to display the status of device system uptime and WAN information. Refresh Button: Click the Refresh button to update the current device status. Auto Button: Click the Auto button to update the status information periodically.

  • Page 28: Status | Lease Status

    Zoom User Manual V1.0 Status | Lease Status Select Status > Lease Status to view the current status of client host PC such as host name, host PC’s MAC address, IP address, and remaining lease time. Refresh Button: Click the Refresh button to display the updated information of the client host PC.

  • Page 29: Wifi

    Network Name (SSID): Define the service set identifier that represents the “name” of your network. (Default value will be “Yes Zoom” - “last 6 digits of your device MAC Address”) Radio Channel: Select the appropriate channel for your Wi-Fi network.
  • Page 30 Zoom User Manual V1.0 Working Mode: Select the wireless operation mode for your Wi-Fi network. (The selection contains 802.11b/g/n, 802.11b/g, 802.11g/n, 802.11b only, 802.11g only and 802.11n only) Bandwidth: Select the channel bandwidth for 802.11n only. Transmit Power: Select the Wi-Fi transmit power from the drop down menu.
  • Page 31 Zoom User Manual V1.0 Preamble Length: Define the length of preamble, either short or long. SSID Broadcast: Broadcast your SSID into open air by checking this checkbox, which is checked in default. Otherwise uncheck the checkbox to make your device invisible unless a wireless client already knows the SSID.
  • Page 32 Zoom User Manual V1.0 ACL Setting: System Default: Select the filter action for the device access control. Disable: Select disable to disable access control WiFi > Access Control List (ACL) feature. Allow: To create a MAC filter list that allows the specific clients to have access to the wireless network.
  • Page 33 Zoom User Manual V1.0 Deny: To create a MAC filter list that will block the specific clients to have access to the wireless network. Insert Button: Click Insert to add MAC address (up to 10) to the list. Del Button: Click Del to remove MAC address from the list.

  • Page 34: Voip

    Zoom User Manual V1.0 VoIP Select VoIP to enable or disable the VoIP feature. Enable Line1: Check on this checkbox to enable VoIP feature or uncheck it to disabled. Cancel Button: Click the Cancel button to clear the changes that you have made on this window.

  • Page 35: Network

    Zoom User Manual V1.0 Network Web Login from Internet This function enables the Zoom to be accessed from external networks, typically from the internet. To enable this function, follow the procedures below: Step 1: Go to Network. Then click Basic.

  • Page 36: Network | Basic

    Zoom User Manual V1.0 Network | Basic Select Network > Basic to configure the basic network settings. Operation Mode: Displays the operation mode of the firewall. Enable Firewall: Click the checkbox to enable device firewall. Enable Web Login from Internet: Enabling this option will allow you to access the device from other networks by https.
  • Page 37 Zoom User Manual V1.0 Enable ping from internet: The device will respond to a ping request from the internet if this option is enabled. Enable UPnP IGD: When this option is enabled, certain Windows applications would setup the port forwarding rule dynamically.

  • Page 38: Network | Internet Protocol

    Zoom User Manual V1.0 Network | Internet Protocol Select Network > Internet Protocol to configure the internet protocol. Connection Mode: Displays the current connection mode of the device to the WiMAX network. Host Name: Enter the host name provided by your service provider (optional).

  • Page 39: Network | Dhcp Server

    Zoom User Manual V1.0 Network | DHCP Server Select Network > DHCP Server to configure the internal DHCP server settings. This device has a built-in DHCP server that can be used for managing the allotment of IP address for the devices connected to the LAN Port of the device.
  • Page 40 Zoom User Manual V1.0 Cancel Button: Click the Cancel button to clear the changes that you have made on this window. Apply Button: The changes that you have made on this window can be saved in the device by clicking the Apply...

  • Page 41: Network | Lease Reservation

    Zoom User Manual V1.0 Network | Lease Reservation Select Network > Lease Reservation to assign the specific IP addresses to the specific client device connected to the LAN port. Add Button: Click the Add button to enter the lease reservation information.

  • Page 42: Network | Port Forwarding

    Zoom User Manual V1.0 Network | Port Forwarding Select Network > Forwarding to manage the additional port forwarding rules. Add Button: Click the Add button to insert new port forwarding rule. When adding a new port forwarding rule, please select TCP or UDP, and then enter port and IP information such as WAN port range, LAN IP address, and LAN port range.

  • Page 43: Management

    Zoom User Manual V1.0 Management Management | Password Select Management > Password to change the login credential. New Login Password: Enter a new password. Confirm New Login Password: Re-enter the new password to confirm. Cancel Button: Click the Cancel button to clear the changes that you have made on this window.
  • Page 44 Zoom User Manual V1.0 Forgot your password? Press and hold the Reset button for more than 5 seconds to reset IP address, device name and login password to factory default. (Please see “Connector” section in CHAPTER 1 of this document to find the location...

  • Page 45: Management | Device Time

    Zoom User Manual V1.0 Management | Device Time Select Management > Device Time to set the time zone. Current Local Time: Displays current local time. Time Zone: Select the proper time zone for your location from the drop-down menu. Auto Adjust for Daylight Saving Time: You may enable this option if your location observes Daylight Savings Time.

  • Page 46: Management | Device Name

    PC on your internal network by entering the device name on the address bar. The default name is “Yes Zoom” - “last 6 digits of your device MAC Address”.

  • Page 47: Management | Device Name

    Zoom User Manual V1.0 Management | Device Name Select Management > Restore To Factory to clear all users’ configuration and restore to factory default settings. Apply: Click the Apply button to reset the device settings to factory default. Management > Restore To Factory...

  • Page 48: Control Panel

    Zoom User Manual V1.0 Control Panel Control Panel | Software Select Control Panel > Software to manage the software of your device. Software Upgrade Install IPKG: Click Browse button to select the IPKG file and then click Upgrade button to install the selected IPKG.
  • Page 49 Zoom User Manual V1.0 the selected backup file. Otherwise, click on Browse button to select where you want to save your backup file and click on Save button to save the backup file.

  • Page 50: Control Panel | Dynamic Dns

    Dynamic Domain Name Service (DDNS) Dynamic Domain Name Service (DDNS) is a service that allows an internet device such as the Zoom to be remotely reachable by the user although it does not have a fixed IP address. It allows the user to create a friendly URL address (example: zoom.ddnsservice.com) for easy access to the Zoom remotely.
  • Page 51 To use the DDNS service, you will need to register an account with one of above DDNS service providers. Then follow the procedures below to set up the DDNS on Zoom: Step 1: Go to Control Panel. Then click Dynamic DNS.
  • Page 52 Zoom User Manual V1.0 How to use Web Login With DDNS? To remotely accessed Zoom, please ensure you have followed procedures specified in Dynamic Domain Name Service (DDNS) and Web Login from Internet. Step 1: On the browser, type in the user selected URL together with https and port number into the address bar (example: https://zoom.ddnsservice.com:8080).
  • Page 53 Zoom User Manual V1.0 Select Control Panel > Dynamic DNS to configure the DDNS settings. Enable DDNS: Check the checkbox to enable the Dynamic Domain Name Service in order to keep the domain name associated. DDNS Service Provider: Select the address of DDNS service provider from the drop-down menu.

  • Page 54: Control Panel | About

    Zoom User Manual V1.0 Control Panel | About Select Control Panel > About to display the basic information about the device: Service Provider, Product Name, WAN port MAC address, LAN Port MAC address, Model ID, Device hardware version and Serial ID.

This manual is also suitable for:

Yes wifiYes

Table of Contents