Related Manuals for Stanley CS25
Summary of Contents for Stanley CS25
- Page 1 CS25/28 HYDRAULIC POLE CHAIN SAW USER MANUAL Safety, Operation and Maintenance © 2014 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 66205 8/2014 Ver. 9...
-
Page 2: Declaration Of Conformity
Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA... -
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► CS25/28 User Manual... -
Page 5: Safety Precautions
Failure to do so may result in dam- the space provided in this manual. age to the quick couplers and cause overheating of The CS25/28 Hydraulic Pole Chain Saw will provide the hydraulic system. safe and dependable service if operated in accordance •... - Page 6 Do not start cutting until you have a clear work area, secure footing and a planned drop area for falling branches. • Keep all parts of the body away from the saw chain during operation. • Carry the saw with the unit de-energized. 6 ► CS25/28 User Manual...
-
Page 7: Electrical Hazards
345.0 to 362.0 13–02 4.02 15–00 4.58 16–03 4.96 500.0 to 550.0 19–00 5.80 21–09 6.63 23–06 7.17 765.0 to 800.0 27–04 8.34 31–03 9.53 33–10 10.32 1) Exceeds phase-to-ground; elevation factor per 29 CFR 1910.269. CS25/28 User Manual ◄ 7... - Page 8 Tables 1 and 2. Footwear, including lineman’s overshoes, having electri- cal-resistant soles, shall not be considered as providing any measure of safety from electrical hazards. 8 ► CS25/28 User Manual...
-
Page 9: Tool Stickers & Tags
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) CS25/28 User Manual ◄ 9... -
Page 10: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 11: Hose Recommendations
HOSE RECOMMENDATIONS CS25/28 User Manual ◄ 11... -
Page 12: Htma Requirements
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements 12 ► CS25/28 User Manual... -
Page 13: Operation
4-6 gpm /15-22 lpm at 1500-2000 psi/105/140 spool fully out (counter-clockwise) until it hits the stop. bar for the CS25 or a flow of 7-9 gpm/26-34 lpm at 1000-2000 psi/70-140 bar for the CS28. 1. Insert the small plug from the kit (furnished with the tool) into the hole located in the top of the selector 2. -
Page 14: Figure 2. Felling A Tree
5. The felling or back cut is made on the side opposite consult you local Stanley representative or your and at least 2 inches above the horizontal undercut county agent. They can often provide information (the felling cut is made higher as the size of the tree that will make your work safer and more productive. -
Page 15: Figure 3. Crosscutting Logs/Limbs With Pressure On Bottom
Clean out the bar groove and keep the oil hole open. 8. Cut branches must not be left in trees overnight. Turn the bar over to equalize wear on the rails. • Always install a new sprocket with a new chain. CS25/28 User Manual ◄ 15... - Page 16 Never break in a new chain under a heavy cutting Release the trigger and remove the wrench. load. 10. Watch the chain tension carefully for the first half- hour of cutting. 16 ► CS25/28 User Manual...
-
Page 17: Tool Protection & Care
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. •... -
Page 18: Troubleshooting
Correct for proper flow direction. Back-pressure too high. Should not exceed 250 psi/17 bar at rated flow measured at the end of the tool operating hoses. Motor sections oil leakage. Motor face seal failure. Replace as required. 18 ► CS25/28 User Manual... -
Page 19: Specifications
SPECIFICATIONS Capacity CS25 and CS28 ..................12 and 15 inch/30 and 38 cm Cut Lengths Weight (w/o Bar and Chain) ........................8.5 lbs/4 kg Overall Length 10 inch Bar ...........................75 inches/190 cm 12 inch Bar ..........................90 inches/229 cm 15 inch Bar ...........................92 inches/234 cm Pressure CS25 ........................... -
Page 20: Cs25/28 Parts Illustration
CS25 / CS28 PARTS ILLUSTRATION To order complete motor assembly see “Note” on parts list (Page 21). 20 ► CS25/28 User Manual... -
Page 21: Cs25/28 Parts List
CS25 / CS28 PARTS LIST PART PART ITEM DESCRIPTION ITEM DESCRIPTION 19212 CAPSCREW 03782 4-6 GPM DECAL 65834 CHAIN GUARD 12412 ELECTRIC WARNING DECAL 07631 24833 HANDLE ASSY (NOTE: DOES NOT COME WITH SPOOL OR O-RING) 08348 SAW CHAIN – 12 INCH... - Page 22 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulics.com...
Need help?
Do you have a question about the CS25 and is the answer not in the manual?
Questions and answers