Challenge Grass Trimmer; Grass Trimmer - Assembly; Technical Specifications; Component List - Challenge CGT180 Instruction Manual

Challenge Grass Trimmer

SYMBOL EXPLANATION
Read the instruction manual
prior to operation.
Wear eye protection
Do not expose to moisture

TECHNICAL SPECIFICATIONS

Charger voltage : Input: 230V~ 50Hz
Output: 20Vdc 400mA
Battery voltage : 18Vdc
Battery : 15 x 1.2V dc Ni-Cd battery
No-load Speed: 8100rpm
Cutting width : 230mm

COMPONENT LIST

1 On/off switch
2 Safety switch
3 Additional handle
4 Height adjustment locking mechanism
5 Motor housing
2
3
4
5
6
7
8
-4-
HELPLINE NO 08707252949
Keep bystanders away
Do not touch the nylon line
until it stops completely
when replacing new line
Charger time :
Weight :
A-weighted sound pressure level
A-weighted sound power level
Vibration :
6 Guard
7 Cutting head
8 Strimmer line
9 Battery pack
10 Battery release button
1
9
10
8 DETAI L
SCALE 3:1
Locking mechanism on both sides

Grass Trimmer - Assembly

Charging the battery pack
Your grass trimmer need 3-5 hours charge
before use. To charge battery, first remove
battery pack from trimmer. Press the
release button on the battery pack, pull the
battery out.
Power connection
Check the voltage given on the charger
matches the supply voltage.
3 -5hours
Charging the Battery
3.2kg
The charger and grass trimmer battery
: 77dB(A)
pack in this pack are specifically designed
: 87dB(A)
to work together. Do not attempt to use the
2
7.45 m/S
grass trimmer battery pack with any other
charger.
Charging
indicator (Red)
Charging base
Important notes for chargering the
battery
The battery is supplied UNCHARGED
from the factory. It will be necessary to
charger the battery for approximately 3-5
hours before use.
Spool
Do not charge a battery when it or the air
temperature is below 4 C.
Between charge cycles rest the charger for at
Spool cover
least 15 minutes.
In a warm environment or after heavy use,
the battery pack may become too hot to
permit charging. Allow time for the battery
to cool down before recharging.
When the battery is charged for the first
time and after prolonged storage, the
battery will only accept approximately 60%
charge. However, after several charge and
discharge cycles the battery will accept a
100% charge.
To Charge the battery
l Connect the charger to the charging
base, and plug the charger plug into a
suitable 230 volt mains socket, then
insert the battery pack into the charging
base, the indicator (red) will illuminate to
show that charging is taking place.
l A fully-discharged battery will take
approximately 3-5 hours to reach full
charge. When charging is complete,
unplug the charging plug from the wall
socket.
Note: The charger will not automatically
switch off when the battery is full charge,
and the red indicator will remain on. Do not
leave your battery on charge continuously.
This may damage the battery cells.
Warning! Do not charge the battery
exceeds 10 hours.
Using Battery Pack
After charging, you need replace the
battery pack on the grass trimmer body,
before inserting the battery pack into grass
trimmer:
Ensure that any fitting has been fitted
securely and that any adjustment device
has been removed. The relevant fasteners
Power indicator (Green)
have been secured tightly in place and the
work piece is adequately secured.
Note: Always ensure the battery is
disconnected before making any
adjustments.
ASSEMBLY INSTRUCTION
Guard fitting
1. Position motor head/axle as shown in
O
dia 1, with
centre (remove pre-fitted screw)
Dia. 1
2. Position guard with inner side, ie.
moulding facing you as shown in Dia. 2.
HELPLINE NO 08707252949
screw fixing hole at the top
Remove pre-fitted
screw prior to
fitting guard.
-5-