Related Manuals for Clarke CIR220
Summary of Contents for Clarke CIR220
- Page 1 24V DC - 1/2” SQUARE DRIVE IMPACT WRENCH KIT Model No: CIR220 Part No 4500635 OPERATING & MAINTENANCE INSTRUCTIONS GC02/13...
-
Page 2: Table Of Contents
GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. -
Page 3: Technical Specifications
TECHNICAL SPECIFICATION Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 4: Safety Precautions
INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND /OR SERIOUS INJURY. THE TERM” POWER TOOL” IN ALL WARNINGS REFERS TO YOUR CIR220 IMPACT WRENCH. WORK AREA a. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. - Page 5 e. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelleryor long hair can be caught on moving parts. POWER TOOL USE AND CARE a. Do not force the power tool. Use the correct power tool for your application.
-
Page 6: Safety Symbols
IMPACT WRENCH SAFETY INSTRUCTIONS ALWAYS use the impact wrench in the manner and for the functions described in these instructions. ALWAYS ensure the impact wrench is not moving with the switchbar in the centre position when changing sockets etc. c. Use only impact wrench sockets. DO NOT use standard sockets. ALWAYS finish tightening wheel nuts or engine parts with a torque wrench or suitable spanner to the correct torque as recommended by the vehicle... - Page 7 Do not immerse in water or expose it to rain or moisture. This charger is fitted with an isolating safety transformer. The warning symbols attached to the battery pack are as follows; Do not immerse in water or expose it to rain or moisture. Do not allow this product to be subject to fire/incineration.
-
Page 8: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. This product battery charger is provided with a standard 13 amp, 230 volt (50Hz), BS1363 plug for connection to a standard domestic electrical supply. Should the plug need to be changed at any time, ensure that a plug of identical specification is used. -
Page 9: Component Inventory/Identification
COMPONENT INVENTORY The CIR220 is a cordless impact wrench which is rechargeable using the mains power adaptor. Upon receipt, check the components against the following list. Any damage or deficiency should be reported to your CLARKE dealer immediately. • 1 x 24V Impact Wrench •... -
Page 10: Battery Charging
Minimum 4°C /Maximum 50°C. Avoid placing batteries in direct strong sunlight or other heat source. NOTE: Ni-Cad batteries as used in Clarke cordless power tools should be given a full charge when first supplied new. Maximum battery performance will be achieved after approximately 5 complete charge/discharge cycles. -
Page 11: Operation
• The battery should be fully discharged before recharging in order to achieve its optimum performance. Constant topping up after only a small amount of charge has been used will, in effect, reduce its capacity. • Ni-Cad batteries will slowly lose their power whilst in storage. Do not leave the batteries in this state for any length of time. -
Page 12: Maintenance
• Refer to your CLARKE dealer if internal maintenance is required. • Your Clarke impact wrench has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local Clarke dealer. -
Page 13: Environmental Protection
ACCESSORIES A wide range of accessories is available from your nearest CLARKE dealer, for further information, contact your nearest dealer, or telephone CLARKE International Sales department on 01992 565300. -
Page 14: Spare Parts List And Diagram
PARTS DIAGRAM Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the CIR220 and is the answer not in the manual?
Questions and answers