KS-F545 SECTION 1 Important Safety Precautions 1.1 Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. 1-2 (No.49828)
KS-F545 SECTION 2 Disassembly method 2.1 Main body 2.1.1 Removing the front panel assembly Front panel assembly (See Fig.1) (1) Press the release button and remove the front panel as- sembly. Release button Fig.1 2.1.2 Removing the bottom cover (See Fig.2) (1) Turn the main body upside down.
Page 4
KS-F545 2.1.4 Removing the heat sink (See Fig.4) • Prior to performing the following procedure, remove the front panel assembly. (1) Remove the two screws B and two screws C attaching the heat sink on the left side of the main body, and remove the heat sink.
Page 5
KS-F545 2.1.7 Removing the cassette mechanism assembly Cassette mechanism assembly (See Fig.7) • Prior to performing the following procedures, remove the front panel assembly, bottom cover, front chassis, heat sink, rear panel and main board. (1) Disconnect the wire from the connector CN402 on the mecha board.
Page 6
KS-F545 2.1.9 Removing the front board (See Fig.9 to 11) Rear cover • Prior to performing the following procedures, remove the front panel assembly. (1) Remove the four screws K attaching the rear cover on the back side of the front panel assembly. (See Fig.9.) (2) Release the eleven joints g, the front panel assembly and the rear cover become separate.
Page 7
KS-F545 2.2 Cassette mechanism assembly REFERENCE: Prior to performing the following procedures, turn the mode gear on the bottom of the body until the respective part comes to the EJECT position (Refer to Fig.1). Mode gear Fig.1 2.2.1 Removing the cassette guide (See Fig.2)
Page 8
KS-F545 2.2.3 Removing the cassette hanger assembly / cassette holder (See Fig.4 to 7) (1) Check the mode is set to EJECT. Push down the front part Cassette holder assembly of the cassette holder and move in the direction of the ar- row to release the joint c.
Page 9
KS-F545 2.2.4 Removing the side bracket assembly Side bracket assembly (See Fig.8 to 10) Joint i (1) Remove the screw A attaching the side bracket assembly. (2) Detach the front side of the side bracket assembly upward and pull out forward to release the joint i and j in the rear.
Page 10
KS-F545 2.2.5 Removing the pinch arm (F) assembly (See Fig.11 and 12) (1) Remove the polywasher and pull out the pinch arm (F) as- sembly. (2) Remove the compulsion spring. 2.2.6 Removing the pinch arm (R) assembly (See Fig.11 and 12) (1) Remove the polywasher and pull out the pinch arm (R) as- sembly.
Page 11
KS-F545 2.2.8 Removing the head / tape guide Flywheel assembly (F) Belt (See Fig.16 and 17) REFERENCE: It is not necessary to remove the slide chassis assembly. (1) Remove the band attaching the wire to the head. (2) Remove the two screws B, the head and the head support spring.
Page 12
KS-F545 2.2.10 Disassembling the flywheel assembly (F) FFC pad (See Fig.19 and 20) (1) Push and turn counterclockwise the spring holder (F) to re- lease the three joints p on the bottom of the flywheel. (2) The spring holder (F), the TU spring and the friction gear play come off.
Page 13
KS-F545 2.2.13 Removing the gear base arm / gear base link assembly (See Fig.23 to 25) (1) Move the gear base arm in the direction of the arrow. Gear base arm (2) Insert a slotted screwdriver to the gear base spring under...
Page 14
KS-F545 2.2.15 Removing the mode gear Mode gear Mode switch actuator (See Fig.26 and 29) (1) Remove the polywasher on the bottom and pull out the mode gear. 2.2.16 Removing the mode switch actuator (See Fig.26, 27 and 29) (1) Pull out the mode switch actuator at the bottom.
Page 15
KS-F545 2.2.19 Removing the gear base assembly / take up gear / reflector gear (See Fig.30 to 32) (1) Push in the pin d’ of the gear base assembly on the upper Slot e' side of the body and move the reflector gear toward the bottom, then pull out.
Page 16
KS-F545 2.2.21 Removing the side bracket assembly Side bracket assembly (See Fig.33 to 37) Boss g' (1) Remove the eject cam plate spring. (2) Push the joint f’ through the slot to remove the load rack downward. (3) Move the eject cam limiter in the direction of the arrow to release it from the boss g’...
Page 17
KS-F545 2.2.22 Removing the main motor assembly / sub motor assembly (See Fig.38 to 40) (1) Remove the belt at the bottom. Main motor (2) Remove the polywasher and pull out the mode gear. assembly (3) Pull out the reduction gear (B).
KS-F545 SECTION 3 Adjustment 3.1 Adjustment method Test instruments required for adjustment Standard volume position 1. Digital oscilloscope (100MHz) Balance and Bass, Treble volume, Fader 2. Frequency counter meter : Center (Indication "0") 3. Electric voltmeter Loudness, Dolby NR, Sound, Cruise : Off 4.
Page 19
KS-F545 Information for using a car audio service jig 1. We're advancing efforts to make our extension cords common for all car audio products. Please use this type of extension cord as follows. 2. As a U-shape type top cover is employed, this type of extension cord is needed to check operation of the mechanism assembly after disassembly.
Page 20
KS-F545 Arrangement of adjusting & test points Cassette mechanism (Surface) Motor assembly Tape speed adjust Azimuth screw A (Forward) Playback head Azimuth screw B (Reverse) Head section view Playback head Azimuth screw B Azimuth screw A (Reverse) (Forward) 1-20 (No.49828)
Page 21
KS-F545 Item Conditions Adjustment and Confirmation methods S.Values Adjust Head Head height adjustment Test tape: azimuth Adjust the azimuth directly. When you SCC-1659 adjustment adjust the height using a mirror tape, VT703 (10kHz) remove the cassette housing from the mechanism chassis. After installing the cassette housing, perform the azimuth adjustment.
Page 24
KS-F545 4.3 LA4743K (IC301) : Power amp. • Block diagram 2200 F 0.022 F Vcc 1/2 Vcc 3/4 IN 1 OUT 1+ 0.22 F OUT 1- PWR GND1 Protective circuit OUT 2+ IN 2 OUT 2- 0.22 F PWR GND2...
Page 25
KS-F545 • Pin layout • Pin function Pin No. Symbol Function Pin No. Symbol Function Header of IC FLIN Front Lch input Power GND RLIN Rear Lch input Outpur(-) for front Rch ONTIME Power on time control STDBY Stand by input...
Page 27
KS-F545 4.6 TEA6320T-X (IC161) : E.volume • Pin layout OUTRR OUTLR OUTRF OUTLF Vref MUTE CD-CH TAPE TUNER • Block diagram VOLUME 2 MUTE 0 to 55 dB FUNCTION BALANCE ZERO CROSS FENDER REAR POWER DETECTOR SUPPLY VOLUME 1 BASS...
Page 28
KS-F545 4.7 UPD178078GF-597 (IC701) : CPU • Pin layout • Pin function Pin No. Symbol Descriptions ACCDET Power save 1, working together ACC POWER Power save 2 , working together Backup PCNT Power ON/OFF switching output STANDBY Standby position detection input...
Page 29
KS-F545 Pin No. Symbol Descriptions GND2 No use FM/AM middle frequency counter input VDDPLL VDD for PLL FMOSC FM/AM limited generator frequency counter input No use GNDPLL PLL for GND AME0 AM error out output FME0 FM error out output...
Page 30
KS-F545 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY MOBILE ENTERTAINMENT CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.49828) Printed in Japan 20034WPC...
KS-F545 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.
KS-F545 Block diagram MOTOR TAPE IN SW MAIN STAND BY SW MOTOR MODE SW HEAD CN402 CN403 FWD-L FWD-R SPEAKER REW-L MOTOR REAR LINE OUT CONNECTOR REW-R TAPEIN SUBMO+ CP901 MODE J321 SUBMO- STANDBY FLOUT+,FLOUT- REEL IC401 FROUT+,FROUT- PB EQ...
Page 40
KS-F545 VICTOR COMP ANY OF JAP AN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.49828SCH) 2003/04...
KS-F545 PARTS LIST [ KS-F545 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix EE --------- Russian Federation - Contents - Exploded view of general assembly and parts list (Block No.M1) Cassette mechanism assembly and parts list (Block No.MP) Electrical parts list (Block No.01~03)
Page 42
KS-F545 Exploded view of general assmbly and parts list Block No.
Page 43
KS-F545 General assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local ------------ MECHA FSYH4036-050 SHEET GE20136-001A MECHA BKT(L) FSKL2002-002 MECHA BKT(R) QYSDST2606Z SCREW 2.6mm x 6mm(x4) QYSDST2606Z SCREW 2.6mm x 6mm LV40847-002A SPACER GE10043-011A TOP CHASIS...
Page 44
KS-F545 Cassette mechanism assembly and parts list Block No. CDS-802JE3...
Page 45
KS-F545 Cassette mechanism Block No. [M][P][M][M] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local 2-1821-0040-D2S PSW-S 2.1 (x3) 2-1711-5040-16S E RING X-0802-1009S MAIN CHASSIS AS 2-1031-7030-C2S SCREW (x2) X-0802-1002S SLIDE CHASSIS A...
KS-F545 Electrical parts list Main board Block No. [0][1][0][0] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local QEQF1HM-225Z E CAPACITOR 2.2uF 50V M QERF1HM-474Z E CAPACITOR 0.47uF 50V M IC161...
KS-F545 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C981 NCB21EK-104X C CAPACITOR 0.1uF 25V K R728 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J C982 QERF1CM-106Z E CAPACITOR 10uF 16V M...
Page 50
KS-F545 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D616 LNJ308G81/1-3/X S619 NSW0124-001X TACT SW D617 LNJ308G81/1-3/X S620 NSW0124-001X TACT SW D618 LNJ308G81/1-3/X S621 NSW0124-001X TACT SW D619 LNJ308G81/1-3/X D620...
Page 52
KS-F545 Packing materials and accessories parts list Block No. KIT: A6 A9 A10 3-12...
Page 53
KS-F545 Packing and accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local GET0115-001A INST.BOOK ENG RUS GET0115-002A INST.BOOK ENG RUS LV40978-001A CAUTION SHEET BT-54013-5 WARRANTY CARD VND3046-001 SERIAL TICKET VKZ4027-202 PLUG NUT VKH4871-001SS MOUNT BOLT VKZ4328-001...
Page 54
Срок службы (годности), кроме срока хранения дополнительных косметических материалов, упомянутых в предыдущих двух пунктах, не затрагивает никаких других прав потребителя, в частности, гарантийного свидетельства JVC, которое он может получить в соответствии с законом о правах потребителя или других законов, связанных с ним. INSTRUCTIONS ИНСТРУКЦИИ...
Page 55
Как перенастроить Ваше устройство Одновременно нажмите и держите в течение (резервный/включение/аттенюатор) нескольких секунд кнопки SEL (выбор) и (резервный/включение/аттенюатор). В результате этого встроенный микрокомпьютер будет перенастроен. Примечание: Ваши запрограммированные настройки – такие как запрограммированные каналы или настройки звука – также сотрутся. SEL (выбор) Как...
Благодарим Вас за приобретение изделия JVC. Перед тем, как приступать к эксплуатации, пожалуйста, внимательно прочитайте все инструкции с тем, чтобы полностью изучить и обеспечить оптимальную работу этого устройства. СОДЕРЖАНИЕ Как перенастроить Ваше устройство ... ДРУГИЕ ГЛАВНЫЕ ФУНКЦИИ ..15 Как пользоваться кнопкой...
ОСНОВНЫЕ ОПЕРАЦИИ MODE Включение Настройте громкость. Включите устройство. Чтобы повысить громкость. Чтобы понизить громкость. Примечания в отношении управления в одно касание: Когда Вы выбираете источник сигнала в пункте 2 ниже, устройство автоматически включается. Вам не нужно нажимать эту Индикатор уровня Появляется...
ОПЕРАЦИИ С РАДИО MODE Прослушивание радио Чтобы прекратить поиск до того, как найдена радиостанция, нажмите на ту же Вы можете использовать автоматический или кнопку, на которую Вы нажимали для того, ручной поиск при настройке на конкретную чтобы начать поиск. радиостанцию. Примечание: Автоматический...
Сохранение Настройтесь на радиостанцию, которую Вы хотите слушать, пока радиостанций в памяти мигает буква “M” . Вы можете воспользоваться одним из следующих двух методов сохранения Нажмите ¢ , чтобы радиовещательных станций в памяти: настроиться на радиостанции Автоматическое программирование • с более низкими частотами. радиостанций...
Ручное программирование Примечания: • Ранее запрограммированная радиостанция Вы можете запрограммировать до 6 стирается, когда под тем же радиостанций в каждом диапазоне (FM1, запрограммированным номером запоминается FM2, FM3 и AM) вручную. новая радиостанция. • Запрограммированные радиостанции Напр.: Для того, чтобы запомнить стираются, когда...
ОПЕРАЦИИ С МАГНИТОФОНОМ MODE Чтобы остановить Прослушивание кассеты воспроизведение и кнопкой выбросить кассету Вы можете проигрывать магнитные ленты Нажмите на кнопку 0. типа I (нормальные). Воспроизведение кассеты прекращается, и она автоматически выбрасывается из Вставьте кассету в кассетоприемника. Источник сигнала меняется кассетоприемник.
Предотвращение Нахождение начала выскакивания кассеты мелодии Вы можете не допустить выскакивания кассеты и “заблокировать” кассету в Функция Multi Music Scan (поиск музыки) дает кассетоприемнике. Вам возможность автоматически начать Нажмите и держите кнопку TAPE (лента) 23 воспроизведение кассеты с начала и 0 (выброс) в течение более 2 секунд. определенной...
Другие полезные Чтобы отменить Пропуск Пустых Участков, повторите данную операцию и выберите “OFF” функции магнитофона (“ВЫКЛ”) в пункте 3, нажав –. Повторное воспроизведение Пропуск пустых участков на текущей мелодии кассете Вы можете воспроизвести текущую мелодию Вы можете пропускать пустые участки между повторно...
НАСТРОЙКА ЗВУКА Настройка звука Индикация Для того, чтобы: Диапазон Настроить низкие –06 (мин.) (низкие частоты. І Вы можете настроить характеристики звука частоты) +06 (макс.) по Вашему вкусу. Настроить –06 (мин.) (высокие высокие частоты. І Выберите тот параметр, который частоты) +06 (макс.) Вы...
Включение/выключение Выбор предварительно настроенных режимов функции компенсации звучания громкости Вы можете выбрать предварительно Человеческое ухо менее чувствительно к настроенную звуковую настройку в низким и высоким частотам при низком зависимости от жанра музыки. уровне громкости. Каждый раз при нажатии кнопки SCM, Функция...
Сохранение в памяти Повторите пункты 2 и 3, чтобы настроить другие параметры. Ваших собственных настроек звука Чтобы включить функцию компенсации громкости. Вы можете настроить режимы звучания Детали смотрите на • (BEAT, SOFT, POP) по Вашему собственному страницах 13. вкусу и сохранить Ваши собственные настройки...
ДРУГИЕ ГЛАВНЫЕ ФУНКЦИИ Установка часов Для проверки текущего времени на часах или изменения режима работы дисплея Несколько раз нажмите на кнопку DISP Нажмите и держите кнопку SEL (дисплей). При каждом нажатии кнопки режим (выбор) в течение более 2 секунд работы дисплея меняется следующим образом: с...
Page 69
Если требуется, повторите пункты Настройте выбранный параметр 2 и 3, чтобы настроить другие PSM. параметры PSM. Нажмите на кнопку SEL (выбор), чтобы завершить установку. Параметры предпочтительного режима установки (PSM) Установите... Запрограммированная Смотрите заводская страницу настройка – Держите... Выберите... Назад Вперед CLOCK H Настройка...
Отсоединение панели Как присоединить панель управления управления Вставьте левую сторону панели Вы можете отсоединить панель управления, управления в паз на держателе когда выходите из машины. панели. При отсоединении или установке панели управления соблюдайте осторожность, чтобы не повредить разъемы на задней стороне панели...
ВЫЯВЛЕНИЕ НЕИСПРАВНОСТЕЙ То, что может вначале показаться неисправностью, не всегда представляет собой серьезную проблему. Перед тем, как обращаться в центр технического обслуживания, проверьте следующее. Симптомы Причины Способ устранения Невозможно вставить Вы пытались вставить Вставляйте кассету так, • кассету. кассету не той стороной. чтобы...
ТЕХНИЧЕСКОЕ ОБСЛУЖИВАНИЕ Это устройство требует минимум ПРЕДОСТЕРЕЖЕНИЕ: обслуживания, но Вы можете продлить срок его службы, если будете следовать • Не используйте кассеты с отклеившимися приведенным ниже инструкциям. наклейками, иначе это может привести к повреждению устройства. Чистка головки • Подтягивайте пленку для устранения провисания, так...
ТЕХНИЧЕСКИЕ ХАРАКТЕРИСТИКИ СЕКЦИЯ УСИЛИТЕЛЯ [Тюнер MW] Чувствительность: 20 µВ ЗВУКОВОЙ ЧАСТОТЫ Избирательность: 35 дБ Максимальная выходная мощность: Передние: 45 Вт на канал [Тюнер LW] Задние: 45 Вт на канал Чувствительность: 50 µВ Непрерывная выходная мощность (RMS): Передние: 17 Вт на канал в 4 Ω, от 40 Гц до...
Page 75
KS-F545 Installation/Connection Manual Руководство по установке/ подключению 1202KKSFLEJEIN EN, RU ENGLISH РУССКИЙ • • INSTALLATION УСТАНОВКА (IN-DASH MOUNTING) (УСТАНОВКА В ПРИБОРНУЮ ПАНЕЛЬ) • • Before mounting: Перед установкой: Note: Примечание: Note: Примечание:...
Page 76
• When using the optional stay • When installing the unit without using the sleeve • При использовании дополнительной стойки • При установке устройства без использования муфты Note: Примечание: ° ° °. °. Removing the unit Удаление устройства (Be sure to keep the handles after installing it.) (После...
ENGLISH РУССКИЙ ELECTRICAL CONNECTIONS ЭЛЕКТРИЧЕСКИЕ ПОДКЛЮЧЕНИЯ Note: 12 V DC, NEGATIVE ground electrical systems Примечание: 12 В постоянного напряжения с минусом на массе rear ground terminal задний разъем заземления 4 Ω to 8 Ω Be sure to ground this unit to the car’s chassis. 4 Ω...
Page 78
(Cover the terminals of these unused leads with insulating tape, as illustrated above.) – Отсоедините громкоговорители от данного устройства, подключите их к усилителю. Оставьте провода громкоговорителей данного устройства неиспользованными. (Замотайте клеммы этих неиспользованных проводов изоляционной лентой, как показано выше.) INPUT JVC Amplifier JVC Усилитель LINE OUT KS-F545 REAR...
Page 79
Срок службы (годности), кроме срока хранения дополнительных косметических материалов, упомянутых в предыдущих двух пунктах, не затрагивает никаких других прав потребителя, в частности, гарантийного свидетельства JVC, которое он может получить в соответствии с законом о правах потребителя или других законов, связанных с ним. INSTRUCTIONS ИНСТРУКЦИИ...
Page 80
How to reset your unit While holding SEL (select), press (standby/ (Standby/On/Attenuator) on/attenuator) for more than 2 seconds. This will reset the built-in microcomputer. Note: Your preset adjustments — such as preset channels or sound adjustments — will also be erased. SEL (Select) How to use the MODE button If you press MODE, the unit goes into functions mode and the number buttons work as different...
Page 81
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. CONTENTS OTHER MAIN FUNCTIONS ....15 How to reset your unit ........
LOCATION OF THE BUTTONS Control panel Display window Display window 1 2 3 4 MODE Display window (standby/on/attenuator) button 2 +/– buttons i FM band number indicators 3 LOUD (loudness) button FM1, FM2, FM3 4 SEL (select) button o AM band indicator 5 DISP (display) button ;...
BASIC OPERATIONS MODE Turning on the power Adjust the volume. Turn on the power. To increase the volume. To decrease the volume. Note on One-Touch Operation: When you select a source in step 2 below, the power automatically comes on. You do not have to press this button to turn on the power.
RADIO OPERATIONS MODE To stop searching before a station is received, Listening to the radio press the same button you have pressed for searching. You can use either automatic searching or manual Note: searching to tune in to a particular station. FM1 and FM2 : 87.5 MHz –...
Storing stations in memory Tune in to a station you want while “M” is flashing. You can use one of the following two methods to Press ¢ to tune store broadcasting stations in memory. in to stations of higher • Automatic preset of FM stations: SSM (Strong- frequencies.
Notes: Manual preset • A previously preset station is erased when a new station is stored in the same preset number. You can preset up to 6 stations in each band (FM1, • Preset stations are erased when the power supply to FM2, FM3 and AM) manually.
TAPE OPERATIONS MODE Listening to a cassette To stop play and eject the cassette Press 0. Tape play stops and the cassette automatically You can play back type I (normal) tapes. ejects from the cassette compartment. The source changes to the previously selected one. Insert a cassette into the cassette If you change the source, tape play also stops compartment.
Prohibiting cassette ejection Finding the beginning of a tune You can prohibit cassette ejection and can “lock” Multi Music Scan allows you to automatically start a cassette in the cassette compartment. While holding TAPE 23, press 0 (eject) for more playback from the beginning of a specified tune.
Playing the current tune repeatedly Other convenient tape functions You can play the current tune repeatedly (Repeat Skipping the blank portions on the tape Play). You can skip blank portions between the tunes To play back tracks repeatedly (Repeat Play) (Blank Skip).
SOUND ADJUSTMENTS Adjusting the sound Indication To do: Range Adjust the bass. –06 (min.) You can adjust the sound characteristics to your +06 (max.) preference. Adjust the treble. –06 (min.) Select the item you want to adjust. Each time you press the button, +06 (max.) the adjustable items change FAD*...
Selecting preset sound modes Turning on/off the loudness function You can select a preset sound adjustment suitable to the music genre. The human ear is less sensitive to low and high Each time you press SCM, the sound mode frequencies at low volumes. changes as follows: The loudness function can boost these frequencies to produce a well-balanced sound at...
Storing your own sound Repeat step 2 and 3 to adjust the adjustments other items. To turn on or off the loudness You can adjust the sound modes (BEAT, SOFT, function. POP) to your preference and store your own adjustments in memory. •...
OTHER MAIN FUNCTIONS To check the current clock time or change the Setting the clock display mode Press DISP (display) repeatedly. Each time you Press and hold SEL (select) for more press the button, the display mode changes as follows: than 2 seconds so that one of the PSM items appears on the display.
Page 94
Repeat steps 2 and 3 to adjust the Adjust the PSM item selected. other PSM items if necessary. Press SEL (select) to finish the setting. Preferred Setting Mode (PSM) items Factory- Set... preset page settings – Select... Hold... CLOCK H Hour adjustment Back Advance...
Detaching the control panel Attaching the control panel Insert the left side of the control panel You can detach the control panel when leaving into the groove on the panel holder. the car. When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder.
TROUBLESHOOTING What appears to be trouble is not always serious. Check the following points before calling a service center. Symptoms Causes Remedies • A cassette tape cannot You have tried to insert a Insert the cassette with the be inserted. cassette in the wrong way.
MAINTENANCE This unit requires very little attention, but you will CAUTION: be able to extend the life of the unit if you follow the instructions below. • Do not play the cassettes with peeling labels; otherwise, they can damage the unit. To clean the head •...
SPECIFICATIONS AUDIO AMPLIFIER SECTION [MW Tuner] Sensitivity: 20 µV Maximum Power Output: Selectivity: 35 dB Front: 45 W per channel Rear: 45 W per channel [LW Tuner] Continuous Power Output (RMS): Sensitivity: 50 µV 17 W per channel into 4 Ω, 40 Hz Front: to 20 000 Hz at no more than CASSETTE DECK SECTION...
Page 100
KS-F545 Installation/Connection Manual Руководство по установке/ подключению 1202KKSFLEJEIN EN, RU ENGLISH РУССКИЙ • • INSTALLATION УСТАНОВКА (IN-DASH MOUNTING) (УСТАНОВКА В ПРИБОРНУЮ ПАНЕЛЬ) • • Before mounting: Перед установкой: Note: Примечание: Note: Примечание:...
Page 101
• When using the optional stay • When installing the unit without using the sleeve • При использовании дополнительной стойки • При установке устройства без использования муфты Note: Примечание: ° ° °. °. Removing the unit Удаление устройства (Be sure to keep the handles after installing it.) (После...
Page 102
ENGLISH РУССКИЙ ELECTRICAL CONNECTIONS ЭЛЕКТРИЧЕСКИЕ ПОДКЛЮЧЕНИЯ Note: 12 V DC, NEGATIVE ground electrical systems Примечание: 12 В постоянного напряжения с минусом на массе rear ground terminal задний разъем заземления 4 Ω to 8 Ω Be sure to ground this unit to the car’s chassis. 4 Ω...
Page 103
(Cover the terminals of these unused leads with insulating tape, as illustrated above.) – Отсоедините громкоговорители от данного устройства, подключите их к усилителю. Оставьте провода громкоговорителей данного устройства неиспользованными. (Замотайте клеммы этих неиспользованных проводов изоляционной лентой, как показано выше.) INPUT JVC Amplifier JVC Усилитель LINE OUT KS-F545 REAR...