Panasonic AW?HE120WP Operating Instructions Manual page 36

Parts and their functions
 LAN connector for IP control [LAN ACT/LINK]
This LAN connector (RJ45) is connected when exercising
IP control over the unit from an external device.
Use a cable with the following specifications for the
connection to the LAN connector:
When connecting through a hub:
LAN cable* (category 5 or above, straight cable),
max. 100 m [328 ft]
When a hub is not used:
LAN cable* (category 5 or above, crossover cable),
max. 100 m [328 ft]
*: Use of an STP (shielded twisted pair) cable is
recommended.
 HDMI connector [HDMI]
This is the HDMI video output connector.
 Anti-theft wire mounting hole
The anti-theft wire bracket (available from a hardware
store) is attached here.
 Service switch [SERVICE]
This switch is used for maintenance purposes: Do not
touch it.
If it is pressed by mistake, the service screen will be
displayed. If this happens, turn off the power and then turn
it back on.
 G/L IN connector [G/L IN]
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the
video signal format which has been set.
Format
1080/59.94p(i)
1080/59.94i
720/59.94p
480/59.94p(i)
480/59.94i
1080/50p(i)
1080/50i
720/50p
576/50p(i)
576/50i
p  Locking to a subcarrier is not possible with BBS.
 VIDEO OUT connector [VIDEO OUT]
This is the output connector used for monitoring the
camera's composite video signals. Use the monitor in the
internal synchronization mode.
Provide a BNC coaxial cable as the connecting cable.
There is a delay in the VIDEO OUT signal output by 120H
(HD lines) when at 720p and at 90H (HD lines) for any
other.
36
(continued)
External sync signal input format
BBS Tri-level sync
480/59.94i 1080/59.94i
480/59.94i 1080/59.94i
— 720/59.94p
480/59.94i —
480/59.94i —
576/50i 1080/50i
576/50i 1080/50i
— 720/50p
576/50i —
576/50i —
 Hole used to secure cable cover
Use the screw provided to secure the cable cover.
 SDI OUT connector [HD/SD SDI OUT]
This is the SDI video signal output connector.
 HD/SD analog output connector
[HD/SD ANALOG OUT]
This is the output connector of the camera's HD/SD
component video signals.
Provide a D-Sub 15-pin connecting cable (VGA cable)
or D-Sub 15-pin and BNC coaxial connector conversion
cable as the connecting table.
Use a high-quality cable.
Pin No. Signal name Pin No. Signal name
1
2
3
4
5
6
7
8
 DC IN connector [12V
Connect the AC adaptor supplied with the unit to this
connector to supply the DC 12 V voltage to the unit.
 Cable clamp
This is used to hold the cable connection to the DC IN
connector and prevent it from becoming disconnected.
 IR ID switches [IR ID]
[CAM1] [CAM2]
These are used to select the ID of the wireless remote
control (optional accessory).
The IR ID switch settings "CAM1" to "CAM4" correspond
to the [CAM1] to [CAM4] buttons on the wireless remote
control.
 Square holes (2) for cable cover tabs
The tabs on the two sides of the cable cover are fitted into
these holes.
 Threaded hole (thread: 1/4-20UNC, ISO1222
[6.35 mm]) for mounting the camera
Use this hole when mounting the camera on a tripod, etc.
R/P 9 GND
r
G/Y 10 GND
B/P 11 GND
b
GND 12 GND
GND 13 —
GND 14 —
GND 15 GND
GND
IN ]
[CAM3] [CAM4]