Table of Contents
Advertisement
2. Preparation
Open the rear cover page to read the following:
The letter identifiers on the rear cover page correspond to those in the body of this page.
2.4 Setting the Date and Time
Set the monitor to the correct date and time before taking a measurement for the first time.
1.
Press the
The year flashes on the
2.
Push or button to change the year.
Push
button to confirm the year and then the month flashes. Repeat the same
steps to change the month, day, hour, and minute.
Year
Change
Confirm
: Forward
: Back
3.
Press the START/STOP button to turn the monitor off.
Notes:
• If the batteries have been replaced, the date and time setting will need to be reset.
• If the date and time are not set, "-/ - -:--" appears during or after measurement.
Date/Time setting (
C
T
Date/Time display.
Month
Change
Confirm
) button.
Day
Hour
Change
Confirm
Change
Minute
Confirm
Change
Confirm
EN
11
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
Need help?
Do you have a question about the BP785N and is the answer not in the manual?
Questions and answers
Machine is no longer tracking info on my phone
The provided context does not mention any phone connectivity features for the Omron BP785N. If your device is not tracking information on your phone, check if it supports Bluetooth or other connection methods. If it does, ensure that Bluetooth is enabled, the device is paired correctly, and any required app is installed and functioning. If the issue persists, refer to the instruction manual or contact customer support.
This answer is automatically generated
how to change mode from average of three bp to one time reading
To change the mode from averaging three blood pressure readings to a one-time reading on the Omron BP785N, follow these steps:
1. Turn on the device but do not start a measurement.
2. Press the button that controls the reading mode.
3. Look for the option that enables or disables the three-reading average mode.
4. Use the arrow button to switch it off.
5. Confirm the setting by pressing the button again.
This will set the device to take a single blood pressure reading instead of averaging three.
This answer is automatically generated
Blood pressure reading high compared to Dr office reading
My machine takes a measurement but when it is supposed to show blood pressure it starts over
The provided context does not contain specific troubleshooting steps for the issue where the Omron BP785N restarts instead of displaying the blood pressure reading. However, general troubleshooting steps for electronic blood pressure monitors include:
1. Check the Power Source – Ensure the batteries are properly installed or the AC adapter is securely connected.
2. Reset the Device – Remove and reinsert the batteries or unplug and reconnect the power adapter.
3. Proper Usage – Make sure the cuff is correctly positioned and you are following the correct measurement procedure.
4. Avoid Interference – Ensure there are no electronic devices nearby that may cause interference.
5. Consult the Manual – Refer to the instruction manual for troubleshooting guidance.
6. Contact Support – If the issue persists, consider reaching out to Omron customer support.
If the issue continues, professional inspection may be needed.
This answer is automatically generated
change date
To change the date on the Omron BP785N blood pressure monitor:
1. Press the button to enter the date setting mode.
2. The year will start flashing. Use the arrow buttons to adjust the year.
3. Press the button again to move to the month setting. Use the arrows to change the month.
4. Press the button again to move to the day setting and adjust it with the arrows.
5. Continue pressing the button to cycle through and confirm the settings.
Once finished, the date and time will be set, and the monitor will be ready for use.
This answer is automatically generated
update date
My Omron BP786N always reads higher than doctor's office monitor. How do I reset it?
To reset the Omron BP785N blood pressure monitor to take a single measurement instead of three, you need to adjust the TruRead Mode. Press the clock-like symbol to access the TruRead settings. Use the arrows to turn the mode off. Once set, press the Start/Stop button to save and exit.
This answer is automatically generated
I changed the batteries and now I can’t get the monitor to let me change the date or set the date
To set the date on the Omron BP785N blood pressure monitor after changing the batteries:
1. Press the Date/Time setting button. The year will flash on the display.
2. Use the up or down button to change the year.
3. Press the button to confirm. The month will flash.
4. Repeat the same steps to set the month, day, hour, and minute.
5. Press the START/STOP button to turn the monitor off after setting is complete.
This answer is automatically generated