Ic Block Diagram - Sanyo ICR-B100 Service Manual

IC BLOCK DIAGRAM

The figure which isn't mentioned please watch a schematic diagram.
IC401 UPD703017 (MICRO COMPUTER)
No. Pin Name I/O
1 LCD DATA I/O LCD Driver IC data output
2 LCD CLK I/O LCD Driver IC clock output
3 P CON O Power control (Power ON=high)
4 A MUTE1 O Audio mute (Mute=high)
5 A MUTE2 O Audio mute (Mute=high)
6 VDD O Power supply
7 VSS O GND
8 DAC PWR O DAC Power control (Power OFF=LOW)
9 DD PWR O DD Converter power control (Power ON=high)
10 PULL UP O PULL UP Resister power control (Power ON=high)
11 AMP PWR O AMP Circuit power control (Power ON=high)
12 MCLK IN I MCLK Count input
13 ADC POW O ADC Power control (Power OFF=LOW)
14 ADC CLK O A/D,D/A Converter master lock output
15 DAC LRCK I/O ADC/DAC LRCK output
16 BEEP O Beap signal output
17 LCD RESET I/O LCD Controller Reset output
18 IC/VPP General action =LOW/FLASH time = high
19 USB 0 I/O Data input/output
20 USB 1 I/O Data input/output
21 USB 2 I/O Data input/output
22 USB 3 I/O Data input/output
23 USB 4 I/O Data input/output
24 USB 5 I/O Data input/output
25 USB 6 I/O Data input/output
26 USB 7 I/O Data input/output
27 USB WR O Data lead select (Lead=LOW)
28 USB RD O Data lead select (Lead=LOW)
29 USB STP I Device detector (Permission=HIGH)
30 USB CE O Chip enable (Enable=LOW)
31 RESET I Reset signal
32 XT1 I
33 XT2
34 VDD
35 X2 Main oscillation (Ceramic 16.384 MHz)
36 X1 I Main oscillation (Ceramic 16.384 MHz)
37 VSS GND
38 CLKOUT
39 I/O
40 WPB O Write protect
41 R/B I Ready/Busy check (Busy=low)
42 WEB O Write enable
43 REB O Lead enable
44 CEB O Chip enable
45 ALE O Address ratch
46 CLE O Command ratch
47 I O0 I/O Smart media (input/output data)
48 I O1 I/O Smart media (input/output data)
49 I O2 I/O Smart media (input/output data)
50 I O3 I/O Smart media (input/output data)
Function
- 7 -
No. Pin Name I/O
51 I O4 I/O Smart media (input/output data)
52 I O5 I/O Smart media (input/output data)
53 I O6 I/O Smart media (input/output data)
54 I O7 I/O Smart media (input/output data)
55 BVDD
56 BVSS
57 USB ON I USB ON/OFF check (ON=High)
58 AC IN I AC Adapter detect (AC have=LOW)
59 MIC IN I Detect the external mic presence (There is a Mic=LOW)
60 SSFDC SW I SmartMedia insert switch
61 SSFDC IN I Detect the SmartMedia presence (Yes=LOW)
62 SSFDC 3V I Detect the 3.3V SmartMedia (3.3V=High)
63 SSFDC REC I Check write on a SmartMedia (Ability=High)
64 R/B I/O
65 MIC SEL1 O Mic change control
66 MIC SEL 2 O Mic change control
67 MIC SEL 3 O Mic change control
68 MIC SENS1 O Mic sensitivity control (1)
69 MIC SENS2 O Mic sensitivity control (2)
70 SEL 24H I Select the 12H/24H change (12H=LOW)
71 AVDD
72 AVSS
73 AVREF
74 KEY0 I Key input
75 KEY1 I Key input
76 FOOT IN I FOOT SW input
77 BATT IN I Battery residual quantity check
78 HOLD SW I Hold SW input
79 FAST SW I High speed listening (ON=LOW)
80 SLOW SW I Low speed listening (ON=LOW)
81 VAS IN I Sound signal level detect
82 LEVEL IN I Volume/VAS sensitivity level input
83 I
84 CASE SW I Battery lid detect switch
85 I
86 O
87 O
88 USB STOP O
89 O
90 ENROL I Enrol output permission (Permission=LOW)
91 O
92 O
93 LCD CS I/O LCD Driver IC chip select output
94 RTC DATA I/O Real time clock IC data output
95 LCD RS I/O LCD Driver IC resister select output
96 RTC CLK I/O Real time clock IC clock output
97 DAC IN I ADC serial data input
98 DAC OUT O DAC serial data output
99 DAC CLK O ADC/DAC clock output
100 O
Function