Av tuner receiver / 5 and 7-channel power amplifier / dvd/sacd player / av surround sound receiver / dvd/cd players / dvd/cd/mp3 player / av surround sound receiver / stereo integrated amplifier / cd player (20 pages)
Identification of controls FRONT PANEL Identification of controls REAR PANEL ATTENTION! Please make all connections to your L70 receiver with the unit unplugged. (It is also advisable to power-down or unplug all associated components while making or breaking any signal or AC power connections.) 120 VOLT NORTH AMERICAN VERSION ONLY...
PRODUCT SAFETY SERVICING GUIDELINES CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN VOLTAGE MEASURE MUST NOT EXCEED 75 VOLTS R.M.S. ANY WAY. NEVER PERFORM CUSTOMIZED INSTALLATIONS THIS CORRESPONDS TO 0.5 MILLIAMP AC ANY VALUE WITHOUT MANUFACTURER’S APPROVAL. UNAUTHORIZED EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL MODIFICATIONS WILL NOT ONLY VOID THE WARRANTY, BUT SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY.
SERVICING PRECAUTIONS CAUTION : Before servicing the A/V Receiver covered by this Electrostatically Sensitive (ES) Devices service data and its supplements and addends, read and follow the Some semiconductor (solid state) devices can be damaged easily by SAFETY PRECAUTIONS. NOTE : if unforeseen circumstances static electricity.
SPECIFICATIONS Amplifier Section FM Tuner Section (Without notes 100.1 MHz, 65 dBf) Output Power (Front) : F.T.C Rating: Tuning Range : 60 watts RMS per channel minimum, both channels 87.5 MHz - 108.0 MHz C: 50 kHz steps driven into 8 ohms from 20 Hz to 20kHz with no AH: 100 kHz steps more than 0.09% total harmonic distortion AM Suppression Ratio: C: 50 dB...
PRINCIPAL PARTS LOCATION RESET PROCEDURE FOR Receiver Functions Only: Press Play then Stop then the FM/AM key, holding in the FM/AM key for more than 5 seconds. RESET PROCEDURE FOR DVD-Player Functions Only: Select DEFAULTS to restore factory defaults. The factory default password is 1234.
(L70AH) EXPLODED VIEW C S 10 S 17 S 15 S 10 S16 X4 S 11 S 10 C MX1A140 B AR R IE R C MX1A139 INS ULAT OR C UP 11556-2 S UB T R ANS AS S 'Y COP11555 L70 PCB AMP ASSEMBLY S 15...
Page 11
IC PIN FUNCTION (IC81 : TMP87PS71AF(OTP)-ANAM 1359DAT(MICOM) PIN No. SYMBOL DESCRIPTION OSD_H OSD INPUT SENSING PORT REMOTE REMOTE CONTROL DATA INPUT PORT RDS_CK CLK/DATA PORT FOR RDS IC(SA6579TV1) RDS_DA F_MUTE FUNCTION MUTE CONTROL OUTPUT PORT("H") EVOL_DA DATA / CLK / CHIP ENABLE CONTROL PORT FOR ELECTRONIC VOL. IC(M62446AFP) EVOL_CK EVOL_CE TEST...
Page 14
AUDIO DSP(CS49326 : IC41) PIN No. Pin Name Function 1,12,23 +VD1 Digital Power supply. Normally +2.5v 2,13,24 DGND Digital Ground AUD3 SPDIF transmitter output/Digital audio output(N.C) Host write strobe pin(connected to GND with an external resistor) Host parallel output enable pin(pulled up with an external resistor) CS_DA SPI Serial data input pin CS_CK...
Page 15
NJU3713 (IC28 : EXPANDER / MAIN) DATA BLOCK DIAGRAM DATA Controller Circuit 2-16...
Page 20
M62446FP (ELECTRONIC VOLUME/INPUT : IC13) SYSTEM BLOCK DIAGRAM C in Cout SW in SWout SL in SLout volume SR in SRout BYPASS1 BYPASS2 tone L in Lout R in Rout µ-com interface volume LATCH DATA CLK PIN CONFIGURATION AND IC INTERNAL BLOCK DIAGRAM OUT4 DVDD OUT3...
Page 30
HY29F400 (FLASH MEMORY : IC03) PIN CONFIGURATIONS BLOCK DIAGRAM DQ[15:0] A[17:0], A-1 STATE C O N T R O L ERASE VOLTAGE I/O BUFFERS G E N E R A T O R A N D DQ[15:0] S E C T O R S W I T C H E S C O M M A N D W E # REGISTER...
Page 31
HY29F400 SIGNAL DESCRIPTIONS t i b t i b s - i t i b s - i s - i t i r e l i t i r s - i l l a e l i e l i l l i d i l s i r...
Page 32
EEPROM : IC13 PIN CONFIGURATION PIN NAME Pin name I / O Function Power supply Ground (0V) A0, A1, A2 Out of use. Please connect to GND. Serial clock input Slave and word address, I / O serial data input, serial data output Wite protect pin * 1 An open drain output requires a pull-up resistor.
SECTION 3 ELECTRICAL PARTS LIST RESISTORS AND CAPACITORS Notes : • Part numbers are indicated for most mechanical parts. Please use this part number for parts order. • IMPORTANT SAFETY NOTICE. Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacture's specified parts.