Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kuzma STABI M
Summary of Contents for Kuzma STABI M
- Page 1 KUZMA STABI M TURNTABLE ( without arm ) S/N…….. Instruction manual 2013-5...
-
Page 2: Table Of Contents
KUZMA LTD INSTRUCTION MANUAL FOR STABI M turntable The Stabi M turntable is a very precisely engineered piece of equipment. However the construction is robust and requires minimal maintenance for optimal performance. Top plate Outer main frame CONTENTS: Page General Tech. -
Page 3: General
General STABI M is a modern turntable designed in a classic turntable style with the emphasis on providing the best possible record playback. The turntable's size allows even 12 inch tonearms to be mounted and covered with its massive acrylic dust cover on spring hinges. The dust cover is constructed not to pick up any vibration from loud music. -
Page 4: Tech. Data
Technical data: Mass 60 kg Platter mass 12 kg Platter material aluminium& acrylic Bearing type ruby ball- inverted Shaft diameter 16 mm Chassis/levelling aluminium/yes Turntable levelling Motor 1 DC ( three phase) Belt material special External power supply Speeds 33, 45, 78 ( see page 10) Armboard No. -
Page 5: Unpacking And Assembling
Unpacking The larger crate contains the outer frame with top plate and lid. Unscrew the top screws and remove the inner top foam. Remove side foam around lid first and put it aside. Then remove the wooden floor plate and top foam. Remove the side foam around the turntable and then two people should lift it up and position it on a strong support. - Page 6 3mm gap between the frame and the outer edge of the top of the plate. When gently pushed down with both hands it will barely move. Remove the protection cup from the bearing shaft. Be sure that it is clean. Locate the PVC bottle with bearing oil and cut the top off the nozzle to allow drops to be poured onto the shaft.
-
Page 7: Setting Up Turntable
Note: Be careful when positioning the platter onto the subplatter if the armboard is already mounted on the top chassis. There is only a small gap. Platter: Position the platter on the subplatter, holding the platter with both hands at the sides. Due to the small gap between the lower edge of the platter and the top of the subchassis, do not hold the platter underneath. - Page 8 Be sure that you have an armboard with the correct pre-cut. Mount armbase on the armboard and then mount armboard on the turntable with four Allen keys. Fix firmly. The armboard can be fixed in both directions, so be sure you mount it correctly orientated. If necessary a second cut can be made on the armboard, but this is made of aluminium.
- Page 9 General description: The DC motor controller unit generates a precise sine wave output to control rotation of a three phase frequency controlled DC motor. The signal is generated by a sophisticated computer based program. This allows for smooth generation of the sine wave with very fine choice of speed.
-
Page 10: Use And Adjustment
Use and adjustments Platter rotation: Ensure that the red LED lights up and the green display shows the selected speed, when the PS DC is switch on. Press the start button. It is normal to hear some crackling sounds made by the belt and this will disappear in a few days. -
Page 11: Maintenance
The clamp can be also used without washers. Gently screw down the clamp on top of the record. It is advisable to put a washer under the LP (thin for thick records and thick for thin records) before screwing the clamp down. Observe the outer edge of the LP. To start with this edge will be above the mat but will slowly lower to touch the mat. -
Page 12: Transportation
All parts are heavy and can be easily damaged by sliding around a transport vehicle. Repacking in the original boxes is, therefore, recommended. Kuzma Ltd Hotemaze 17A SI-4205 PREDDVOR SLOVENIJA...
Need help?
Do you have a question about the STABI M and is the answer not in the manual?
Questions and answers