Table of Contents
Advertisement
Quick Links
Read the instructions carefully and follow the rules for safe
operation.
Failure to do so could result in serious injury.
ECHO, INCORPORATED
400 Oakwood Road, Lake Zurich, Illinois 60047-1564
Phone : 847-540-8400
INSTRUCTION MANUAL
CHAIN SAW
WARNING
Printed in Japan 1402m 1137 ES
CS-800P
X750-023 86 0
X750 315-230 0
Advertisement
Table of Contents
Related Manuals for Echo CS-800P
Summary of Contents for Echo CS-800P
-
Page 1: Instruction Manual
INSTRUCTION MANUAL CHAIN SAW CS-800P WARNING Read the instructions carefully and follow the rules for safe operation. Failure to do so could result in serious injury. ECHO, INCORPORATED X750-023 86 0 400 Oakwood Road, Lake Zurich, Illinois 60047-1564 Phone : 847-540-8400... - Page 2 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Copyright © 2013 All Rights Reserved.
-
Page 3: Rules For Safe Operation
4. Cut at high engine speeds. 5. Do not overreach or cut above shoulder height. 6. Follow manufacturer’s sharpening and maintenance instructions for the saw chain. 7. Only use replacement bars and chains specified by the manufacturer or the equivalent. CS-800P... - Page 4 SAE Standard J335 are standard to the rear, and the muffler away from on ECHO chain saws to reduce the your body. When carrying a chain saw possibility of forest fires. with the engine running, push the front...
-
Page 5: Table Of Contents
The enclosed message provides information CAUTION necessary for the protection of the unit. The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided. CS-800P... - Page 6 Do not operate this chain saw unless you sheet shown in the instruction manual. have extraordinary cutting needs and experience and specialized training for dealing with kickback. ECHO chain saw with significantly reduced kickback potential are available. Locate this safety decal on your unit. The complete Part Number X505-002041 unit illustration found in the “NOMENCLATURE OF...
-
Page 7: Packing List
The ECHO product you purchased has been After opening the carton, check for damage. factory pre-assembled for your convenience. Immediately notify your retailer or ECHO dealer of Due to packaging restrictions, guide bar and saw damaged or missing parts. chain installation and other assembly may be Use the packing list to check for missing parts. -
Page 8: Nomenclature Of Parts
* If a decal cannot be read, a new one can be dealing with kickback. ECHO chain saw with significantly reduced kickback potential ordered from your ECHO dealer. are available. - Page 9 23. Cylinder cover - The cooling airflow grill. 10. Clutch cover - Protective cover to the guide It covers the cylinder, spark plug and bar, saw chain, clutch and sprocket when silencer. the chain saw is in use. CS-800P...
-
Page 10: Operator Safety
If this guideline is not followed, hearing loss can numbness in the fingers. occur. The following precautions are strongly ECHO recommends wearing hearing protection recommended because the minimum exposure at all times. which might trigger the ailment is unknown. WEAR PROPER CLOTHING neck, feet and ankles and hands and wrists. -
Page 11: Spark Arrestor Muffler
ECHO chain brakes have been designed and Reduced radius belongs on top tested to comply with international safety standards as follows. -
Page 12: Preparation For Use
Never start or operate saw if brake band is not in place Unlock chain brake on clutch drum. Always check chain brake operation after replacing cover. Do not use saw if chain brake does not function properly. CS-800P... -
Page 13: Adjusting Chain Tension
5. Pull the chain around the bar by hand. Loosen the adjustment if you feel tight spots. 6. When chain is properly tensioned, tighten clutch cover nuts securely - 20 to 23 N·m (175 to 200 in. lb.). 7. Keep chain properly tensioned at all times. CS-800P... -
Page 14: Fuel And Lubricant
ISO-L-EGD (ISO/CD 13738) and JASO M345-FC/FD certified oil, such Fuel Mix Chart 50 : 1 as ECHO premium Power Blend X™, will void the U.S. Metric two-stroke engine warranty. Gasoline... -
Page 15: Emission Data
(This is an example only, information on THIS ENGINE MEETS U.S. EPA EXH/EVP EMISSION REGULATIONS FOR MODEL YEAR * * * * REFER TO OWNER’S MANUAL label varies by engine family). FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS. * * * ? ? ? ? CS-800P... -
Page 16: Operation
(Chain brake unlocked position) • Never use throttle latch for cutting. Choke control knob • Use the chain brake only in starting or in Choke emergencies. Starter handle Unlock chain brake CS-800P... -
Page 17: When The Engine Is Cold
Chain brake Run” position. starter handle. Choke control knob firing sound, pull throttle trigger to release choke. Choke open towards the operator immediately. Unlock chain brake (Chain brake unlocked position) CS-800P... -
Page 18: Checking Chain Tension
If engine does not stop, pull choke control knob Ignition switch out fully to stop engine. STOP Return the unit to your authorized ECHO dealer Throttle trigger to check and repair stop switch before starting the engine again. CHECKING CHAIN TENSION during work and corrected as necessary. -
Page 19: Cutting Instruction
CUTTING INSTRUCTION GENERAL CAUTION • Read the ECHO “CHAIN SAW SAFETY MANUAL” included with your chain saw for additional cutting and safety instructions. • Wear suitable hearing protection such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. -
Page 20: Felling The Tree
Then remove the saw for the second cut. Insert the saw in the first cut, very carefully so as not to cause kickback. The final cut is made by drawing the saw forward in the cut to reach the hinge. CS-800P... - Page 21 • The chain saw industry and government agencies have attempted to prescribe various safety devices, but the best protection is to avoid kickback. • Comply with the safety precautions as listed in this Manual and Safety Manual. CS-800P...
-
Page 22: Chain Brake Operation
When the brake lever trips, the chain should stop. Immediately release the throttle trigger. WARNING If the chain does not stop immediately, return the saw to your authorized ECHO dealer for Chain brake unlock repair. When the lever is fully pulled toward the operator, brake is unlocked. -
Page 23: Automatic Chain Brake
4. The impact should lock the chain brake. IMPORTANT When checking the operation of the automatic chain brake, use a soft surface substance like wood to provide the impact so the chain is not damaged. Rear handle should be gripped lightly with the right hand. CS-800P... -
Page 24: Chain And Guide Bar Combination
CHAIN AND GUIDE BAR COMBINATION The following combinations are recommended for model CS-800P. Guide bar Saw chain ECHO Part No. Length mm (in.) Pitch mm (in.) ECHO Part No. Links Symmetrical 508 (20) 20D0PS3870 72LPX70CQ 610 (24) 24D0PS3881 72LPX81CQ 686 (27) 27D0PS3893 9.53 (3/8) -
Page 25: Maintenance And Care
MAINTENANCE AND CARE Your ECHO chain saw is designed to provide many SKILL LEVELS hours of trouble free service. Regular scheduled Level 1 = Easy to do. Most required tools come maintenance will help your chain saw achieve that with unit. -
Page 26: Carburetor Adjustment
If a tachometer is available idle speed should be To maintain proper engine operation and emission set to 2800 r/min. compliance above 1100 feet ASL the carburetor may need to be adjusted by an authorized ECHO CAUTION service dealer. When starting, idling adjustment speed... -
Page 27: Air Filter
Fuel tank cap Fuel filter the tank out with gasoline can clean it. OIL FILTER lubricating system. Oil filter steel wire or the like. Oil tank cap the tank out with gasoline can clean it. CS-800P... -
Page 28: Automatic Oiler
When the knob touches stopper and stops, this position indicates maximum discharge Adjusting knob volume. (15 mL/min at 7000 r/min) - Do not turn the adjusting knob beyond the maximum or minimum limit of volume adjustment. CS-800P... -
Page 29: Setting The Saw Chain
Keep the lower edge of the drive link sharp where indicated. SETTING SAW CHAIN diameter 7/32 in.) and flat file are used. Keep this angle ® the file holder (Sure Sharp 25° Push file as shown 10° Hold the file tipped 10° upward CS-800P... - Page 30 - If the saw chain becomes soiled with resin, for instance, clean it with kerosene and soak in it oil. NOTICE Parallel These angles are referred to as Oregon 72LPX. To sharpen other follow chain manufacturer’s instruction. Depth gauge CS-800P...
-
Page 31: Troubleshooting
Dies or accelerates poorly runs arrestor screen blocked WARNING Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result. CS-800P... -
Page 32: Storage After Use
Recoil starter Power transmission Automatic centrifugal clutch Fuel Mixture ratio 50 : 1 ratio with ECHO Power Blend X™, ISO-L- EGD (ISO/CD 13738) and JASO M345-FC/FD two- stroke, air-cooled engine oil. Gasoline Use 89 octane unleaded. Do not use fuel containing methyl alcohol, more than 10 % ethyl alcohol or 15 % MTBE. -
Page 33: Warranty Statements
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your ECHO unit to an authorized ECHO servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been made. - Page 34 89 octane or higher. Gasohol which contains a maximum 10 % ethanol (grain alcohol) or 15 % MTBE (methyl/ tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
Need help?
Do you have a question about the CS-800P and is the answer not in the manual?
Questions and answers