Table of Contents
Advertisement
T M
Single Control Centerset Lavatory
Faucet with Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet with the
Speed Connect Drain, a feature found only on American Standard faucets.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect Drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Screwdriver
1
INSTALL FAUCET
Apply a bead of putty along the edge of the underside of the FAUCET (1).
Insert FAUCET (1) and CABLE CONNECTOR (2) through center hole
of mounting surface. Fig. A.
From under side of mounting surface thread the two MOUNTING
NUTS (2) onto FAUCET SHANKS (4). Fig. B.
Center FAUCET (1) and hand tighten MOUNTING NUTS (3) to
secure FAUCET (1).
3
(HAND TIGHTEN)
Fig. B.
Channel Locks
Turn off hot and cold water
CAUTION
supplies before beginning.
Installation
Instructions
8115F
8115SF
Adjustable Wrench
Plumbers' Putty or Caulking
1
PUTTY
4
1
Certified to comply with ANSI A112.18.1
M 9 6 8 7 9 7 R e v. 1 . 8
Tubing Cutter
Fig. A.
3
2
Advertisement
Table of Contents
Related Manuals for American Standard CADET 8115F
Summary of Contents for American Standard CADET 8115F
- Page 1 • Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the Speed Connect Drain. Helpful tips for removing your current drain can be found in the Troubleshooting section of these instructions.
- Page 2 INSTALL POP-UP DRAIN Fig. A. Fig. B. REAR OF SINK Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN Fig. A. POP-UP (3). Drop DRAIN BODY (4) through sink drain hole. Make sure WHITE FOAM GASKET (5) Fig.
- Page 3 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig.
- Page 4 TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Ensure that AERATOR (3) is tightened completely. Operate HANDLE (1) to allow water flow. CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink.
-
Page 5: Troubleshooting Guide
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: •... - Page 6 To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper LOGO slightly if necessary so that the Stopper slides all the way down.
- Page 7 TIPS FOR REMOVING YOUR OLD DRAIN: Most existing drains can be removed quickly and easily with only a pair of channel- lock pliers or a wrench. However, there may be situations where it is difficult to remove your old drain or determine how the drain is disassembled. Depending upon the existing Drain in your sink, it is either removed from above or below the sink.
- Page 8 CADET SINGLE CONTROL M962133-0020A CENTERSET FAUCET M962133-2950A HANDLE KIT with Speed Connect Drain M907265-0070A MODEL NUMBER PLUG BUTTON 8115F 030746-0070A HANDLE SCREW KIT 8115SF M907301-0020A M907301-2950A Appropriate finish code CHROME M918506-0070A SATIN NICKEL CARTRIDGE SCREWS A951470-0070A CARTRIDGE M950158-0020A M950158-2950A LIFT ROD M922880-0020A M952430-0070A M922880-2950A...
Need help?
Do you have a question about the CADET 8115F and is the answer not in the manual?
Questions and answers