Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Paslode CF-325
Summary of Contents for Paslode CF-325
- Page 1 Model CF- 902245-3 01/09...
-
Page 2: Introduction And Warranty
Service Center listing that was provided with your tool. ONE-YEAR LIMITED WARRANTY Paslode's sole liability hereunder will be to replace any part or accessory which proves to be defective within the specific time period. Any replacement A one-year warranty will apply to all parts, except those listed... -
Page 3: Table Of Contents
Contents Introduction and Warranty ............2 An Overview of the Paslode Cordless Framing Nailer ....4 Safety Instructions..............5 Battery and Charging System ........... 8 Fuel Cell and Metering Valve ..........10 Preparing the Paslode Cordless Framing Nailer for Use ..13 Paslode Cordless Framing Nailer Operation ......14 Fasteners and Applications ............. -
Page 4: An Overview Of The Paslode Cordless Framing Nailer
Intermittent Operation – 2 to 3 nails Cycle Rate: As with any internal combustion motor, the Paslode Cordless per second Nailer will require periodic maintenance to keep it operating at it's peak performance. The cleaning procedure booklet NOTE: Exceeding these rates could cause tool to overheat, will instruct you on the proper cleaning of your tool. -
Page 5: Safety Instructions
The following safety instructions have been included in this booklet to provide you with basic information necessary for WARNING safe operation of the Paslode Cordless Framing Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY Never expose or store the PRECAUTIONS AND MANUAL INSTRUCTIONS. - Page 6 NEVER operate the tool if the work contacting element vicinity of the Paslode is not working properly. Cordless Framing Nailer. 8. ALWAYS POINT THE TOOL AWAY FROM YOURSELF AND OTHERS WHEN CLEARING JAMS OR REMOVING FASTENERS.
- Page 7 Battery Disposal: The Paslode Cordless batteries contain cadmium and must be recycled or disposed of properly. It is illegal in some areas to place a nickel-cadmium battery into the trash or solid waste stream. You may contact your local recycling center for information on where to return the spent battery or call 1-800-822-8837 for information on Ni-Cd battery recycling in your area.
-
Page 8: Battery And Charging System
This charging system 1. Remove wall mount unit with the orange label from is the only one that will work with all Paslode batteries the tool case and plug into a 120V AC outlet. Set (round or oval). - Page 9 Battery and Charging System Battery Indicator Light The illustration is a close-up of the side of the Paslode Cordless framer handle. On the side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light.
-
Page 10: Fuel Cell And Metering Valve
When cleaning the tool, use only operating tool or fuel Paslode Cordless tool oil. Using oils not formulated for the cartridge. Paslode Cordless Tool, may cause loss of power and may damage the internal parts of the tool's motor. - Page 11 Paslode Cordless Fuel Cell/Cartridge Disposal Guidelines Paslode the industry leader in cordless technology provides this information to assist users with the proper disposal of discarded fuel cells/cartridges. Acceptable disposal options vary depending on the type of fuel cell/cartridge users. All users must consider federal, state and local solid waste regulations to ensure that discarded fuel cells/cartridges are disposed of properly.
-
Page 12: Inserting Fuel Cartridge
Quicklode™ Fuel Cartridge Inserting Fuel Cartridge C. Release the adaptor so it is centered on the fuel A. Inserting the fuel cartridge into the Cordless Framing cartridge. Nailer is very simple. To begin, press up at the bottom of the actuator cover and pivot outward to open. -
Page 13: Preparing The Paslode Cordless Framing Nailer For Use
The blank cycling,which could waste fuel and damage ® use of nails that do not meet Paslode standards could cause tool components. Five (5) nails will be left in the tool damage and void your warranty. Paslode nail sizes and... -
Page 14: Paslode Cordless Framing Nailer Operation
Paslode Cordless Framing Nailer Operation PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Fan motor starts, fuel is injected into combustion Move up to Increase chamber and Drive Depth mixed with air by Move Down to Reduce the fan. -
Page 15: Fasteners And Applications
(Not for use in all-weather wood foundations.) Hardened Steel - For attaching wooden plates to green concrete foundations; 2X furring strips to cinder block. The Paslode Cordless Framing Nailer is not recommended for use with 3" Ring Shank nails in pressure treated lumber... -
Page 16: Servicing
Framing Nailer, clearing a jammed fastener is easy: DANGER 1. Remove the fuel cartridge and battery. Never attempt any maintenance of the Paslode Cordless 2. Lock follower back in magazine and remove fasteners. Framing Nailer without first removing the fuel cartridge 3. -
Page 17: Air Filter Servicing
Cordless Framing Nailer Paslode Cordless Tool Accessories A variety of accessories are available for the Paslode Cordless Framing Nailer: No-Mar Work Contacting Element - Part No. 901252 Battery - Part No. 404717 Clear Safety Glasses - Part No. -
Page 18: Troubleshooting
Check lockout. If unable to free return tool to Lockout bracket is stuck in lockout position. fully - tool does not operate. authorized Paslode dealer for service. Remove and inspect lower probe. Clean, Work-contacting element is bent, worn or at adjust or replace lower probe as required. -
Page 19: Paslode
If tool will not operate after following the above service directions, return the tool to an authorized Paslode.® representative for service. For the nearest Paslode® representative call 1-800-682-3428. For factory direct service call 1-800-447-3830. For Technical support call 1-800-222-6990 or visit our web site at www.paslode.com. To purchase parts, visit our website at www.itwconstructionparts.com... -
Page 20: Forest Edge Drive Vernon Hills, Illinois
An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 www.paslode.com...
Need help?
Do you have a question about the CF-325 and is the answer not in the manual?
Questions and answers