Advertisement
Quick Links
II / NORM CE
This product has been designed with respect of the European standards.
- Directive Low Voltage 73/23 CEE of 19th February 1973 (decree n°98- 1081 of 3rd October 1995)
- Directive electromagnetic compatibility 89/336 CEE of 3rd May 1989
This conformity is established in compliance with EN60974-1 and A1/A2 of 2003 (Low voltage Directive) and EN
50199 (Electromagnetic compatibility Directive)
INSTRUCTION MANUAL
FOR SEMI-AUTOMATICAL
WELDING MACHINES
MAGYS 410
GENEGYS 510 SF
GENEGYS 515 WSF
MIG 3
GYS
Mise à jour : 07/11/06
Réf 73326
73326
1
Advertisement
Related Manuals for GYS MAGYS 410
Summary of Contents for GYS MAGYS 410
- Page 1 Mise à jour : 07/11/06 Réf 73326 INSTRUCTION MANUAL FOR SEMI-AUTOMATICAL WELDING MACHINES MAGYS 410 GENEGYS 510 SF GENEGYS 515 WSF II / NORM CE This product has been designed with respect of the European standards. - Directive Low Voltage 73/23 CEE of 19th February 1973 (decree n°98- 1081 of 3rd October 1995)
- Page 2 GYS can’t be responsible for the damages occurred to persons or things, which derive from the use of the machine in following circumstances:...
- Page 3 GENEGYS 515 WSF Protection of the line: MAGYS 410: Circuit breaker 25A curve D or fuse 25A type aM GENEGYS 510 SF and GENEGYS 515 WSF: Circuit breaker 32A curve D or fuse 32A type aM III/ DESCRIPTION OF THE MACHINE...
- Page 4 MAGYS 410: Foreside (Lower part) connection Generator wire feeder Selection commutators of the output allows to lay in gas (connected positive voltage. Terminal – to use a generator wire terminal). superior current 200 A feeder type WF. (position for an using in The connection is SPRAY ARC).
- Page 5 GENEGYS 515 WSF : foreside (higher part) Indicator of Control of the VOLTAGE or cooling liquid group WIRE SPEED measurment Selection indicator of value (VOLTAGE or WIRE SPEED) Indicator of current measurment Button of WIRE quick : it allows for Switch of selection new coils to save for the output...
-
Page 6: Stainless Steel
For an application with a wire in normal polarity, you must connect the adapter earth clamp on the negative terminal and take care to swivel from a ¼ the adapter. MAGYS 410 machine can only operate in normal polarity (positive for the motor) if we used the generator wire feeder. - Page 7 All torches are with a euro connection, which can be adapted on GYS machines. 4-5) Setting of rollers Choose those in function of the wire diameter used and the type of wire (See following board). MAGYS 410 machine is delivered with rollers double groove 0,8 / 1 for steel.
- Page 8 Release: the important coil inertia can drive the wire rolling after end welding. Open the gas. The machine is ready to operate. 4-8)Commissioning of the cooling liquid group ( GENEGYS 515 WSF) • Never operates the cooling group without filling the cooling liquid tank before the use of the machine. •...
- Page 9 VII / OPTION FOR MAGYS 410 MAGYS 410 machine is an evolutive terminal. For origin machine, we can uniquely use this one with the moto wire feeder. Then, we can advanced the product with separated wire feeder with equipping it with a WF wire feeder and a...
-
Page 10: Maintenance
We advice you to clean the covering situated in the torch by blowing it with compressed air. IX / ADJUSTMENTS OF WELDING CYCLES: PREGAZ, POSTGAZ, BURNBACK The evoluated electronic card of MAGYS 410 and GENEGYS 510 SF machines allows intervening on welding parameters. - Page 11 -Control if it is possible to have a better -Protecting gas insufficient. earth connection. -Adjust gas debit. No gas in torch outlet - Bad gas connection - (On MAGYS 410) see if the gas junction near to the motor is correctly connected.
Need help?
Do you have a question about the MAGYS 410 and is the answer not in the manual?
Questions and answers