Winegard SENSAR III Installation & Operation Manual
Hide thumbs
Also See for SENSAR III:
- Installation & operation manual (9 pages) ,
- Installation & operation manual (8 pages)
Advertisement
Quick Links
WINEGARD
INSTALLATION/OPERATION MANUAL (All Models)
Digital Reception
Sensar vs Sensar with Wingman
Excellent
Digital
Reception
Great
Digital
Reception
VHF
UHF
Channels
Channels
2-13
14-51
Sensar only
•RV-WING – White, RV •GS-WING – Gray, Residential
Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601-2000 © Winegard Company, 2004, 2006 2452013 REV6 11/10
WINEGARD
SENSAR
®
MADE IN U.S.A.
(Sensar
III head - U.S. Patent D500,496)
®
(WINGMAN
- U.S. Patent D612,369)
®
(Sensar
IV head - U.S. Patent D620,483)
®
SENSAR
IV ANTENNA
®
VHF
UHF
Channels
Channels
2-13
14-51
Sensar with
Wingman
1
®
ANTENNAS
®
SENSAR
SENSAR
III ANTENNA
®
WITH WINGMAN
ACCESSORY
SENSAR
ANTENNA
®
WITH WINGMAN
• Increases UHF performance up to 100%
• FREE digital programming
• Installs in minutes -
no tools required
III ANTENNA
®
®
®-
Advertisement
Related Manuals for Winegard SENSAR III
Summary of Contents for Winegard SENSAR III
- Page 1 Channels Channels 2-13 14-51 2-13 14-51 Sensar only Sensar with Wingman •RV-WING – White, RV •GS-WING – Gray, Residential Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601-2000 © Winegard Company, 2004, 2006 2452013 REV6 11/10...
- Page 2 A reinforced roof area, or a prewired coax cable, may be available. For sloped/round roofs, use Winegard Model RW-2000 exterior roof wedge, to level installation. An interior wedge, IW-5000, is also available.
-
Page 3: All Models
ALL MODELS FIGURE 6 Leveling Bracket STEP 6: Attach antenna head to lift tubes with two (2) steel pins, Figure 6. Align holes in leveling bracket on Antenna back of antenna head with holes in lift tubes, insert Head pins and secure in place with (2) E-clips. Use pliers and get a firm grip on E-clips. - Page 4 AMPLIFIED MODELS ONLY STEP 11: Select location for wall plate. Run two FIGURE 10 coax cables (RG-6 type recommended) (three if set 2 jack is going to be used) between locations and install connectors on each end. Mark cables so "cable input", "TV output"...
- Page 5 WINEGARD SENSAR ANTENNAS ® ® OPERATION MANUAL (All Models) LUBRICATION (Done 3-4 times annually) RAISING ANTENNA TO OPERATING POSITION STEP 1: To lubricate the elevating gear, apply a liberal amount of silicone spray lubricant to the elevating gear with the lift in the down position (see illustration).
-
Page 6: Test Point
INSTALLING F-CONNECTORS ON COAXIAL CABLE Step 1. Strip outer cover back 1/2"* from end of cable. Fray braid back as far as outer cover will allow. Step 2. Trim braid close to outer cover and remove 1/4"* of inner insulation being careful not to nick center conductor. -
Page 7: Ordering Repair Parts
Repair parts are available at many RV dealers and/or service centers throughout the country. If you don't have a dealer/service center near you, call Winegard Company at 1-800-288-8094. All major credit cards accepted. Parts are available only in the packages shown here. Order by the Model No. of the package needed. - Page 8 If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service. Customer must provide proof of purchase to verify the product is under warranty. If the product is brought to an authorized Winegard dealer for service prior to expiration of year one (1) of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services, Winegard Company will cover the Winegard dealer’s...
Need help?
Do you have a question about the SENSAR III and is the answer not in the manual?
Questions and answers